DOWNLOAD Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C Service Manual ↓ Size: 13.77 MB | Pages: 50 in PDF or view online for FREE

Model
TX-28LK10C TX-28LK10S TX-28SK10C TX-25LK10C
Pages
50
Size
13.77 MB
Type
PDF
Document
Service Manual
Brand
Device
TV / EURO-4H CHASSIS
File
tx-28lk10c-tx-28lk10s-tx-28sk10c-tx-25lk10c.pdf
Date

Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C Service Manual ▷ View online

Colour Television
TX-28LK10C
TX-28LK10C/S
TX-28SK10C
TX-25LK10C
EURO- 4H Chassis
SPECIFICATIONS
(Information in brackets [ ] refers to model TX-28SK10C)
(Information in brackets { } refers to model TX-25LK10C)
Power Source:
220-240V a.c., 50Hz
Power Consumption:
121W {103W}
Standby Power
Consumption:
1,4W
Aerial Impedance:
75
Ω unbalanced, Coaxial Type
Receiving System:
PAL-B/G, H, D/K, PAL-525/60
SECAM B/G, D/K
M.NTSC (AV only)
NTSC (AV only)
Receiving Channels:
VHF E2-E12
VHF H1-H2 (ITALY)
VHF A-H (ITALY)
VHF R1-R2
VHF R3-R5
VHF R6-R12
UHF E21-E69
CATV (S01-S05)
CATV S1-S10 (M1-M10)
CATV S11-S20 (U1-U10)
CATV S21-S41 (HYPERBAND)
Intermediate Frequency:
Video
38,9MHz
Sound
33,4MHz (B/G), 33,16MHz(A2 STEREO)
32,4MHz (D/K)
32,66MHz (CZECH STEREO)
Colour
34,47MHz (PAL)
34,5MHz, 34,65MHz (SECAM)
Video/Audio Terminals:
AUDIO MONITOR OUT
Audio (RCAx2)
500mV rms1k
AV1 IN
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 10k
RGB (21 pin)
0,7V p-p 75
AV1 OUT
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 1k
AV2 IN
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 10k
S-Video IN
Y: 1V p-p 75
(21 pin)
C: 0,3V p-p 75
AV2 OUT
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 1k
AV3 IN (only TX-28LK10C,TX-28LK10C/S  and TX-25LK10C)
Audio (RCAx2)
500mV rms10k
Video (RCAx1)
1V p-p 75
High Voltage:
28kV ±1kV 
{26kV ±1kV}
Picture Tube:
A66ECF50X82 66cm
{A59EAK071X54  59cm}
Audio Output:
2x7W RMS, 2x15W MPO
8
Ω Impedance
Headphones
8
Ω Impedance
Accessories supplied:
Remote Control
2 x R6 (UM3) Batteries
Dimensions:
Height:
575mm
{525mm}
Width:
775mm
{717mm}
Depth:
460mm
{466mm}
Net Weight:
32,5kg
{26kg}
Specifications are subject to change without notice.
Weights and dimensions shown are approximate.
NOTE: This Service Manual should be used in conjunction with the
EURO-4H technical guide.
TECHNISCHE DATEN
(
Die Auskunft in den Klammern [ ] bezeicht sich auf das folgende Modell TX-28SK10C
)
(
Die Auskunft in den Klammern { } bezeicht sich auf das folgende Modell TX-25LK10C
)
Netzspannung:
220-240V a.c., 50Hz
Leistungsaufnahme:
121W {103W}
Standby
Leistungsaufnahme:
1,4W
Antennenimpedanz:
75
Ω asymmetrisch, Koaxial-Typ
Empfangssystem:
PAL-B/G, H, D/K, PAL-525/60
SECAM B/G, D/K
M.NTSC (nur AV Eingang)
NTSC (nur AV Eingang)
Empfangsbereiche:
VHF E2-E12
VHF H1-H2 (ITALY)
VHF A-H (ITALY)
VHF R1-R2
VHF R3-R5
VHF R6-R12
UHF E21-E69
CATV (S01-S05)
CATV S1-S10 (M1-M10)
CATV S11-S20 (U1-U10)
CATV S21-S41 (HYPERBAND)
Zwischenfrequenz:
Video
38,9MHz
Sound
33,4MHz (B/G), 33,16MHz(A2 STEREO)
32,4MHz (D/K)
32,66MHz (CZECH STEREO)
Colour
34,47MHz (PAL)
34,5MHz, 34,65MHz (SECAM)
Video/Audio Anschlüsse:
AUDIO MONITOR OUT
Audio (RCAx2)
500mV rms1k
AV1 EINGANG
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 10k
RGB (21 pin)
0,7V p-p 75
AV1 AUSGANG
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 1k
AV2 EINGANG
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 10k
S-Video IN
Y: 1V p-p 75
(21 pin)
C: 0,3V p-p 75
AV2 AUSGANG
Video (21 pin) 
1V p-p 75
Audio (21 pin) 
500mV rms 1k
AV3 EINGANG (nur TX-28 LK10C,TX-28LK10C/S und TX-25LK10C)
Audio (RCAx2)
500mV rms10k
Video (RCAx1)
1V p-p 75
Hochspannung:
28kV ±1kV 
{26kV ±1kV}
Bildrohre:
A66ECF50X82 66cm
{A59EAK071X54  59cm}
Ton Ausgangsleistung:
2x7W RMS,2x15W MPO
Lautsprecher
8
Ω Impedanz
Kopfhörer:
8
Ω Impedanz
Mitgel. Zubehör:
Fernbedienung
2 x R6 (UM3) Batterien
Abmessungen:
Höhe:
575mm
{525mm}
Breite:
775mm
{717mm}
Tiefe:
460mm
{466mm}
Gewicht:
32,5kg
{26kg}
Änderungen der Technisichen Daten vorbehalten.
Gewichte und Abmessungen sind Näherungsangaben.
Hinweis: Bitte verwenden Sie das Service Manual zusammen mit dem
Technical Guide.
ORDER No. 01-SM-001
CONTENTS
SAFETY PRECAUTIONS .................................................... 2
SERVICE HINTS ................................................................. 4
SERVICE POSITION ........................................................... 5
SELF CHECK ...................................................................... 6
ADJUSTMENT PROCEDURE ............................................. 7
WAVEFORM PATTERN TABLE .......................................... 8
ALIGNMENT SETTINGS ..................................................... 9
BLOCK DIAGRAMS............................................................. 11
PARTS LOCATION.............................................................. 15
REPLACEMENT PARTS LIST............................................. 16
SCHEMATIC DIAGRAMS.................................................... 28
CONDUCTOR VIEWS ......................................................... 35
SUPPLEMENT 1 - CRT CHANGE  ...................................... 40
SUPPLEMENT 2 – POWER FACTOR CORRECTION  ....... 41
MODIFIED SCHEMATIC DIAGRAMS ................................. 42
MODIFIED P.C.B. ................................................................ 45
INHALT
SICHERHEITSVORKEHRUNGEN ...................................... 2
SERVICE HINWEISE .......................................................... 4
SERVICEPOSITION FÜR DAS CHASSIS ........................... 5
SELBSTDIAGNOSE ............................................................ 6
ABGLEICH .......................................................................... 7
SIGNAL TABELLE............................................................... 8
ABGLEICHTABELLE ........................................................... 10
SCHALTBILD BLOCK.......................................................... 11
EXPLOSIONSZEICHNUNG................................................. 15
ERSATZTEILLISTE ............................................................. 16
SCHALTBILD SCHEMA ...................................................... 28
ANSICHT DER LEITERBAHNEN ........................................ 35
NACHTRAG 1 - BILDSCHIRMÄNDERUNG ........................ 40
NACHTRAG 2 - BEGRENZUNG DES HARMONISCHEN
STROMS ............................................................................. 41
MODIFIZIERTE SCHEMATISCHE DIAGRAMME  ............... 42
MODIFIZIERTES P.C.B....................................................... 45
SAFETY PRECAUTIONS
GENERAL GUIDE LINES
1.  It is advisable to insert an isolation transformer in the
a.c. supply before servicing a hot chassis.
2.  When servicing, observe the original lead dress in the
high voltage circuits. If a short circuit is found, replace
all parts which have been overheated or damaged by
the short circuit.
3.  After servicing, see that all the protective devices
such as insulation barriers, insulation papers, shields
and isolation R-C combinations are correctly
installed.
4.  When the receiver is not being used for a long period
of time, unplug the power cord from the a.c. outlet.
5.  Potentials as high as 29kV {27kV} are present when
this receiver is in operation. Operation of the receiver
without the rear cover involves the danger of a shock
hazard from the receiver power supply. Servicing
should not be attempted by anyone who is not
familiar with the precautions necessary when working
on high voltage equipment. Always discharge the
anode of the tube.
6.  After servicing make the following leakage current
checks to prevent the customer from being exposed
to shock hazard.
LEAKAGE CURRENT COLD CHECK
1.  Unplug the a.c. cord and connect a jumper between
the two prongs of the plug.
2.  Turn on the receiver’s power switch.
3.  Measure the resistance value with an ohmmeter,
between the jumpered a.c. plug and each exposed
metallic cabinet part on the receiver, such as screw
heads, aerials, connectors, control shafts etc. When
the exposed metallic part has a return path to the
chassis the reading should be between 4M ohm and
20M ohm. When the exposed metal does not have a
return path to the chassis the reading must be
infinite.
SICHERHEITSVORKEHRUNGEN
ALLGEMEINE RICHTLINIEN
1.  Es ist empfehlenswert einen Trenntransformator in
die Stromversorgung zu schalten, bevor Reparaturen
an einem Gerät vorgenommen werden, dessen
Chassis unter Spannung steht.
2.  Bei der Durchführung von Servicearbeiten dürfen die
ursprünglichen Kabelanschlüsse nicht vertauscht
werden. Dies gilt insbesondere für die Anschlüsse im
Hochspannungsteil. Hat sich ein Kurzschluß ereignet,
dann sind alle Teile, an denen Spuren von
Überhitzung sichtbar sind, auszuwechseln.
3.  Nach Beenden der Servicearbeiten ist
sicherzustellen, daß alle Sicherheitsvorrichtungen,
wie Isolationsstege, Isolationspapiere,
Abschirmungen und Isolations -R-C- Glieder wieder
richtig eingesetzt sind.
4.  Wenn der Fernseher während längerer Zeit nicht in
Betrieb gesetzt wird, sollte der Netzstecker aus der
Netzsteckdose gezogen werden.
5.  Im Betrieb sind Spannungen bis zu 29kV {27kV} in
diesem Gerät vorhanden. Die Inbetriebnahme des
Fernsehers ohne aufgesetzte Rückwand bringt die
Gefahr eines elektrischen Schlages von der
Fernseher - Stromversorgung mit sich.
Servicearbeiten solten daher auch nie durch
Personen versucht werden, die nicht in vollem.
Umfang mit den Sicherheitsvorkehrungen beim
Umgang mit Hochspannungsgeräten vertraut sind.
Vor der Handhabung mit der Bildröhre ist die Anode
der Bildrohre immer an dem Empfängerchassis zu
entladen.
6.  Nach Beenden der Servicearbeiten sind die
folgenden Kriechstrom-Prüfungen durchzuführen, um
den Kunden vor der Gefahr eines elektrischen
Schlages zu schützen.
MESSUNG DES ISOLATIONSWIDERSTANDES
IM ABGESCHALTETEN ZUSTAND
1.  Den Netsztecker aus der Netzsteckdose ziehen und
die beiden Steckerstifte kurzschließen.
2.  Den Geräteschalter des Fernsehgerätes einschalten.
3.  Mit einem Ohmmeter den Widerstandswert zwischen
dem überbrückten Netzkabelsteckerund jendem
zugänglichen Metallteil am Gehäuse des
Fernsehgerätes, wie Schraubenköpfe, Antennen,
Achsen der Regler, Griffassungen usw.messen.
Wenn ein zugängliches Metallteil keine Rückleitung
zum Chassis hat, Muß die Anzeige unendlich
betrgen.
2
LEAKAGE CURRENT HOT CHECK
1.  Plug the a.c. cord directly into the a.c. outlet. Do not
use an isolation transformer for this check.
2. Connect 
2k
Ω 10W resistor in series with an
exposed metallic part on the receiver and an earth,
such as a water pipe.
3.  Use an a.c. voltmeter with high impedance to
measure the potential across the resistor.
4.  Check each exposed metallic part and check the
voltage at each point.
5.  Reverse the a.c. plug at the outlet and repeat each of
the above measurements.
6.  The potential at any point should not exceed 1,4 V
rms. In case a measurement is outside the limits
specified, there is a possibility of a shock hazard, and
the receiver should be repaired and rechecked before
it is returned to the customer.
X-RADIATION WARNING
1.  The potential sources of X-Radiation in TV sets are
the high voltage section and the picture tube.
2.  When using a picture tube test jig for service, ensure
that the jig is capable of handling 29kV {27kV}
without causing X-Radiation.
NOTE : It is important to use an accurate
periodically calibrated high voltage meter.
1.  Set the brightness to minimum.
2.  Measure the high voltage. The meter should indicate:
28kV ± 1kV {26kV ±1kV} . If the meter indication is
out of tolerance, immediate service and correction is
required to prevent the possibility of premature
component failure.
3.  To prevent any X-Radiation possibility, it is essential
to use the specified tube.
MESSUNG DES KRIECHSTROMS IM
EINGESCHALTETEN ZUSTAND
1.  Den Netzstecker direkt in eine Netsteckdose stecken.
Für diese Messung keinen Trenntransformator
verwenden.
2. Einen 
2k
Ω / 10W-Widerstand in Serie mit einem von
außen zugänglichen Metallteil am Fernsehgerät und
einer guten, Erdung z.B Wasserleitung, anschließen.
3.  Ein Wechselstrom-Voltmeter mit einem Meßbereich
von 1000 Ohm.Volt oder größer verwenden, um die
Spannung über den Widerstand zu messen.
4.  Jedes zugängliche Metallteil prüfen, und an jedem
Punkt dies Spannung messen.
5.  Den Netztecker umgekehrt in die Steckdose stecken
und jede der obigen Messungen wiederholen.
6.  Die Spannung darf an keinem der Punkte 1,4V eff.
überschreiten. Wird dieser Wert nicht eingehalten,
besteht die Gefar eines elektrischen Schlages, und
das Fernsehgerät sollte daher repariert und
nachgeprüft werden, bevor es an den Kunden
zurückgegeben wird.
RÖNTGENSTRAHLUNG ACHTUNG
 :
1.  Potentielle Quellen von Röntgenstrahlung in
Fernsehgeräten sind das Hochspannungsteil und die
Bildröhre.
2.  Bei Verwendung eines Bildröhren-Prüfgerätes für den
Service ist sicherzustellen, daß es für die Belastung
von 29kV {27kV} geeignet ist, ohne daß eine
Röntgenstrahlung verursacht wird.
ANMERKUNG : Es ist wichtig, daß ein präzises,
regelmäßig geprüftes Voltmeter verwendet wird.
1.  Helligkeit auf Minimum stellen.
2.  Die Hochspannung messen. Die Anzeige des
Instrumentes sollte: 28kV ± 1kV {26kV ±1kV}.
Falls die Anziege diese Toleranzgrenzen
überschreitet, ist die sofortige Behebung nötig, um
die Möglichkeit vorzeitigen Komponentenausfalls zu
verhüten.
3.  Um die Möglichkeit von Röntgenstrahlung zu
begrenzen, ist es wichtig, daß nur die
vorgeschriebene Bildröhre verwendet wird.
3
HOT CHECK CIRCUIT
2k ohm
10W
a.c. VOLTMETER
Water Pipe
    (Earth)
TO INSTRUMENT'S
EXPOSED
METALLIC PARTS
SCHALTUNGSAUFBAU FÜR PRUFUNG
IM EINGESCHALTETEN ZUSTAND
WECHSELSTROM-VOLTMETER
AN ZUGANGLICHE
METALLTEILE DAS
TV-GERATES
Wasserleitung
    (Erdung)
Fig. 1
Abb. 1
SERVICE HINTS
HOW TO REMOVE THE REAR COVER
1.  Remove the 8 screws as shown in 
Fig. 2.
SERVICE HINWEISE
ENTFERNEN DER GERÄTERÜCKWAND
1.  Die 8 Schrauben entfernen, siehe 
Abb. 2
.
LOCATION OF CONTROLS
LAGE DER EINSTELLREGLER
4
Fig. 3
Abb. 3
N-Board
Y-Board
E-Board
F-Board
Focus
Fokusregler
Screen
Schirmgitteregler
P-Board
W-Board
Fig. 2
Abb. 2
SCREWS
SCHRAUBEN
SCREWS
SCHRAUBEN
Page of 50
Display

Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C Service Manual ▷ Download

  • DOWNLOAD Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C Service Manual ↓ Size: 13.77 MB | Pages: 50 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C in PDF for free, which will help you to disassemble, recover, fix and repair Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C TV. Information contained in Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.