Panasonic TH-65LFB70E Service Manual ▷ View online
*1: Based on SMPTE 274M standard.
*2: Based on SMPTE RP211 standard.
*3: Based on SMPTE 295M standard.
*4: The input signal is recognized as 1,125 (1,080) / 60p.
*5: When selected the RGB format and 525p signal input to the PC IN terminal, it is recognized as VGA 60 Hz signal.
*6: When inputted VGA 60Hz format signal from the other than PC IN terminal, it is recognized as 525p signal.
*7: Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal
Board (TY-FB11DHD) is installed.
Note: Signals without above specifications may not be displayed properly.
*2: Based on SMPTE RP211 standard.
*3: Based on SMPTE 295M standard.
*4: The input signal is recognized as 1,125 (1,080) / 60p.
*5: When selected the RGB format and 525p signal input to the PC IN terminal, it is recognized as VGA 60 Hz signal.
*6: When inputted VGA 60Hz format signal from the other than PC IN terminal, it is recognized as 525p signal.
*7: Based on SMPTE 292M and 372M standards. These signals can be received when the Dual Link HD-SDI Terminal
Board (TY-FB11DHD) is installed.
Note: Signals without above specifications may not be displayed properly.
9
Specifications
Power Source: 220-240V AC, 50 / 60Hz
Rated Power Consumption:
215W
Stand-by Power Consumption: 0.5W
Operating Conditions:
Temperature: 0°C
40°C
Humidity:
20%
80% RH (non condensing)
Applicable signals:
Colour System
NTSC, PAL, PAL60, SECAM, Modified NTSC
Scanning Format
525(480) / 60i • 60p, 625(575) / 50i • 50p, 750(720) / 60p• 50p
1125(1080) / 60i • 60p • 50i • 50p • 24p • 25p • 30p • 24psF, 1250 (1080) / 50i
PC signal
VGA, SVGA, XGA, SXGA, UXGA . . . . . (compressed)
Horizontal scanning frequency 15 - 110kHz
Vertical scanning freguency 48 - 120Hz
Terminals:
AV IN
VIDEO
BNC
1.0 Vp-p (75
)
AUDIO 1 IN
Stereo mini jack (M3) x 1
0.5 Vrms, Shared with COMPONENT/RGB IN
HDMI 1
TYPE A Connector x 2
HDMI 2
COMPONENT/RGB
IN
Y/G
BNC
with sync 1.0 Vp-p (75
)
Pb/Cb/B
BNC
0.7 Vp-p (75
)
Pr/Cr/R
BNC
0.7 Vp-p (75
)
AUDIO 1 IN
Stereo mini jack (M3) x 1
0.5 Vrms, Shared with VIDEO
DVI-D IN
DVI-D 24Pin
Compliance with DVI Revision 1.0
Content Protection
Compatible with HDCP 1.1
AUDIO 2 IN
Stereo mini jack (M3) x 1
0.5 Vrms, Shared with PC IN
PC IN
High-Density Mini D-sub 15 Pin Y or G with sync 1.0 Vp-p (75
)
Y or G without sync 0.7 Vp-p (75
)
Pb/Cb/B: 0.7 Vp-p (75
)
Pr/Cr/B: 0.7 Vp-p (75
)
HD/VD: 1.0 – 5.0 Vp-p (high impedance)
AUDIO 2 IN
Stereo mini jack (M3) x 1
0.5 Vrms, Shared with DVI-D IN
SERIAL External
Control
Terminal
D-sub 9 Pin
RS-232C compatible
PC OUT
R: 0.7 Vp-p (75
)
G: 0.7 Vp-p (75
)
B: 0.7 Vp-p (75
)
HD/VD: 1.0 – 5.0 Vp-p
USB (VIEWER)
TYPE A USB connector
USB (TOUCH)
TYPE B USB connector
DIGITAL LINK / LAN
For RJ45 network and DIGITAL LINK connections, compatible with PJLink™
Communication method: RJ45 100BASE-TX
EXT
SP
8
,
20W [10W + 10W] (10% THD)
Sound:
Speakers
120mm x 40mm x 2pcs
Audio Output
20W [10W + 10W] (10% THD)
10
LCD screen: L5EDDYY00643
1920 x 1080, 16:9
Visible
Diagonal
1638mm
Accessories supplied :
Remote Control
2 x R6 (UM3) Batteries
2 xPen
Pen Tray
Eraser
USB Cable
Dimensions:
Width:
Height: Depth:
1,517mm 892mm 106mm
Mass:
58.0kg
Design and Specifications are subject to change without notice. Mass and dimensions shown are approximate.
This equipment complies with the EMC standards listed below:
EN61000-3-2, EN61000-3-3, EN55022, EN55024
11
Service Mode
CAT (Computer Aided Test) Mode
CAT (Computer Aided Test) Mode
IIC Mode
Select the IIC mode by Up/Down buton on the remote control at the front page of CAT mode and then press the Action
button on the remote control.
button on the remote control.
1. Select the alignment Subject by Up/Down buttons
on remote control.
2. Select the alignment Item by Left/Right buttons
on the remote control.
3. Adjust
optimum setting by Volume Up/Down buttons
on the remote control.
4. The
data is memorized when press the R button
on the remote control or change the alignment
Subject (or Items).
Subject and Item are mentioned on “IIC mode structure”.
To exit the IIC mode, press the R button on remote control.
CAT panel sys. 8.2
IIC Mode
CD Mode
NW Mode
SD Mode
MS Mode
ID mode
Mode Function
Access
Button
IIC Mode
Service Alignment
Action
CD (Complete
Diagnostic)
Diagnostic)
Software version
information EEPROM edit
information EEPROM edit
Mute
more than 3 seconds
more than 3 seconds
NW Mode
LAN terminal check
Action
SD (Status Display)
MTBF parameter
Action
MS Mode
Market Select
Mute
more than 3 seconds
more than 3 seconds
ID Mode
LSI Check
Mute
more than 3 seconds
more than 3 seconds
Y 525/480)/60p
16:9 STANDARD Mid
LCD W/B Adj.
R Drive
FE FE
16:9 STANDARD Mid
LCD W/B Adj.
R Drive
FE FE
CAT mode menu
Remote Control
MUTE
VOL Up/Down
Up/Down
R
Left/Right
ACTION
RECALL
How to access the CAT mode.
OSD
Subject
Item
New data
Original data
How to access the CAT mode.
Method A Main unit + remote control operation
Press and hold the button on the right side of the unit and press
the RECALL button on the remote kontrol 3 times quickly within 2
seconds, this will placet he unit into the CAT mode.
Method B Remote control operation only
Press and hold the button on the right side of the unit and press
the RECALL button on the remote kontrol 3 times quickly within 2
seconds, this will placet he unit into the CAT mode.
Method B Remote control operation only
1. Set OFF timer except fot [0] minute by OFF TIMER button.
(30 minutes, 60 minutes, 90 minutes)
2. Set the volume level of sound to 0 by VOL down button / -button.
3. Set the RECALL button more than 3 seconds before a volume
display disappears.
To exit CAT mode, turn the power off by main unit or a remote control.
(30 minutes, 60 minutes, 90 minutes)
2. Set the volume level of sound to 0 by VOL down button / -button.
3. Set the RECALL button more than 3 seconds before a volume
display disappears.
To exit CAT mode, turn the power off by main unit or a remote control.
12
Click on the first or last page to see other TH-65LFB70E service manuals if exist.