DOWNLOAD Panasonic TH-65LFB70E Service Manual ↓ Size: 21.12 MB | Pages: 123 in PDF or view online for FREE

Panel W/B Adj. 

R DRIVE 

FE 

G DRIVE 

FC 

B DRIVE 

FA 

by left / right button

  DIGITAL LINK Update 

by up / down  button 

Update Not 

Ready 

Update Ready

EDID Write Protect 

Protect 

Front Panel key Check 

PICTURE Sub Adjust 

White + Time, Temperature 
WHITE 
RED 
GREEN 
BLUE 
BLACK 

Key Check -- 

TEMP CONTROL Adj 

Main Contrast1 

0 

R sub Bright1 

0 

G sub Bright1 

0

 

Chroma Control 

GUN OFF 

0 

Pos./Size 

H Position 

81 

V Position 

80 

H Size 

80

 

B DRIVE 

00

 

Aging 

Panel Color 

These are selected by Action buton of Remote control and press the R button to exit. 

B sub Bright1 

0

 

Threshold Temp 

52 

Offset Temp 

3 

WHITE Ramp 
RED Ramp 
GREEN Ramp 
BLUE Ramp 
Color Bar 
Scrolling Vertical Window 

 
1. Self check is used to automatically check the bus line controlled circuit of the LCD display. 
2. To get into the Self check mode, press the volume down button on the customer controls at the right side of the set, at the 
same time pressing the OFF TIMER button on the remote control, and the screen will show. 
 
Method A Self-Check only ( A shipment setup is not carried out ) 

Select ID mode by UP/Down button on the remote control at the front page of CAT mode and then press the Mute button 
on the remote control more then 3 seconds. 

Press and hold the volume down button on the right side of the unit and press the OFF-TIMER button on the remote 
control. 

 

 
If the IIC ports have been checked and found to be incorret, or not located then “- -” will appear in place “OK”   
“01” in the lie of the “PTCP” means the number of blinks of the  Power LED is 1. (Reference_Power LED blinking timing  
        chart) 
“H09” in the line of the “PTCP” is the error code 
 
To exit the CAT mode switch off the main power. 
 
 
Note: 
The line of the “PTCP” display when you get into the Self check mode for first time only after the Power LED blinks. 
 
 
 
 
 
 
 
 

 

 
 
 
 
 

 
            
 
 
               A      H90MEM1         

OK

                DS     H51RTC       

OK

 

                         H65AVSW        

OK

 

                       H61ADV            

OK

 

                       H62TEMP         

OK

 

                       H63CPG            

OK

 

                       H66HDMIRX     

OK

 

                       H93LAN             

OK

 

                       H92MEM2         

OK

 

                       H56LVDSRX     

OK

 

                       H67DLK             

OK

 

                       H68FRC            

OK

 

 
                                                                     

 

 ID 

IIC1 

IIC2 

IIC3 

IIC4 

 
1. Subject 

Information of LED Flashing timing chart. 

 
2. Contents 

When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the 
defective block can be identified by number of blinking of the Power LED on the front panel of the unit. 

 

 

Blinking times 

Contents & Check point 

Check point 

1 

PTCT 01 H09]*  
PANEL SOS 

LCD PANEL 

 

2 

(PTCT E2 H09)* 
POWER SOS 

P-Board 
A-Board 

(PTCT 04 H09)* 
POWER SOS 

4 

(PTCT 04 H09) 
PANEL 12V SOS 

A-Board 
LCD Panel 

8 

(PTCT 0A H09) 
FRC SOS 

A-Board 

10 

(PTCT 0B H09)* 
FAN SOS 

DS-Board 
SLOT Board 

11 

(PTCT 0B H09) 
FAN SOS 

FAN 
A-Board 

13 

(PTCT 0D H09)* 
REGULATOR SOS (A2 SOS) 

A-Board 

(PTCT 1D H09)* 
REGULATOR SOS (5V SOS) 

(PTCT 2D H09)* 
REGULATOR SOS (A2 SOS) 

(PTCT 4D H09)* 
AUDIO SOS 

To find the possible failure point  where in LCD Panel or Printed Circuit Board when the abnormal picture is displayed. 
 

(A) Main unit + remote control operation 
1. While pressing [VOLUME (-)] button of the main unit, press [R] button of the remote control three times within 2 seconds. 
2. Test pattern is displayed and Power LED lights red and orange alternately.  
 
How to Exit: Turn off the unit. 
 
 
(B) Remote control only 
1. Press [Recall] button of the remote control. 
2. Press [R] button of the remote control. 
3. Press [N] button of the remote control for over 3 seconds. 
4. Test pattern is displayed and Power LED lights red and orange alternately. 
 
How to Exit: The unit automatically turns off after around 10 seconds. 
 
[Display pattern] 
It is unfixed from which color it starts. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

WHITE MAGENTA YELLOW

CYAN  BLACK