Panasonic TH-65BFE1W Service Manual ▷ View online
DIS-3
SECTION 2 DISASSEMBLY PROCEDURES
<65BFE1W>
2. Parts Disassembly
2.1. Precautions
* Before Disassembling, turn the display off and disconnect the power plug from the wall outlet.
* When tore off sticky tapes, please use a new thing without reusing it on the occasion of assembling.
23
TH-50LFB70U/TH-50LFB70W
7.2. Preparations
• When you exchange modules or board, in order to make it
discharge from an electrolytic condenser, please wait for 1
minute after the power supply end.
minute after the power supply end.
• To avoid damaging the LCD panel, lay out a soft cloth or
towel and lay down the unit so the front side is facing down.
Precautions when replacing each component
• When you replace each component, please be sure to carry
out following procedure as below.
• Be careful not to overtighten the screws when replacing
each module.
• Please remove a clamper and a wire processing tape if
needed in the repaire.
• In carrying out Section 7.7. or later, please execute the
Chapter 7.6. and 7.5. in advance.
7.3. Replacement of WI-FI Module
(Dongle)
1. Remove the screw and then remove the WI-FI Module
(Dongle).
2.2. Preparations
• When you exchange modules or board, in order to make it discharge from an electrolytic condenser, please wait for 1 minute
after the power supply end.
• To avoid damaging the LCD Panel, lay out a soft cloth or towel, and turn the front of the unit down, and lay down so that the
entire monitor rides on a table completely.
Precautions when replacing each component
• When you replace each component, please be sure to carry out following procedure as below.
• Be careful not to overtighten the screws when replacing each module.
• Please remove a clamper and a wire processing tape if needed in the repair.
Precautions when replacing each component
• When you replace each component, please be sure to carry out following procedure as below.
• Be careful not to overtighten the screws when replacing each module.
• Please remove a clamper and a wire processing tape if needed in the repair.
23
TH-65LFB70U/TH-65LFB70W
7.2. Preparations
• When you exchange modules or board, in order to make it
discharge from an electrolytic condenser, please wait for 1
minute after the power supply end.
minute after the power supply end.
• To avoid damaging the LCD Panel, lay out a soft cloth or
towel and lay down the unit so the front side is facing down.
Precautions when replacing each component
• When you replace each component, please be sure to carry
out following procedure as below.
• Be careful not to overtighten the screws when replacing
each module.
• Please remove a clamper and a wire processing tape if
needed in the repaire.
• In carrying out Section 7.7. or later, please execute the
Chapter 7.6. and 7.5. in advance.
7.3. Replacement of WI-FI Module
(Dongle)
1. Remove the screw and then remove the WI-FI Module
(Dongle).
Soft cloth and Towel
DIS-4
SECTION 2 DISASSEMBLY PROCEDURES
<65BFE1W>
2.3. Replacement of LCD Panel and Front Glass
In case of replacing the LCD panel module on the floor, gently place it on the flat floor which has a soft and
cushioned surface.
A top-and-bottom inversion is a bad.
30
TH-50LFB70U/TH-50LFB70W
7.15. Replacement of LCD Panel and Front Glass
Attention when removing LCD Panel
• Please work putting a glove.
Caution about LCD Panel
• When replacing the LCD module, please work to be aware of the following.
DIS-5
SECTION 2 DISASSEMBLY PROCEDURES
<65BFE1W>
31
TH-50LFB70U/TH-50LFB70W
31
TH-50LFB70U/TH-50LFB70W
Note:
Do not twist the LCD panel module.
DIS-6
SECTION 2 DISASSEMBLY PROCEDURES
<65BFE1W>
32
TH-50LFB70U/TH-50LFB70W
Click on the first or last page to see other TH-65BFE1W service manuals if exist.