DOWNLOAD Panasonic TH-55SF2U / TH-55SF2E / TH-55SF2W (serv.man2) Service Manual ↓ Size: 7.33 MB | Pages: 61 in PDF or view online for FREE

ADJ-2

* The software can be updated as the procedure below.

1. USB memory : It stores a file for updating. (FAT32/FAT16 format)

2. Updating file (SF2_MAIN_Vxxxx.img) : Download from the service web site 

and store it into the top directory of USB memory.

1. Turn on the Display and insert the USB memory into the slot of USB.

2. The message below will appear on the screen.

3,  Select [Yes] with [tu] buttons and press the [ENTER] button to start updating.

  If the updating fails, the message below will appears.

  Confirm that updating file is stored into the USB memory correctly and try it again.

 

4. The message below will appear when the updating has been finished correctly.

After finishing the updating, as the Display turn on automatically, remove the USB memory from the slot immediately other-

wise the message to update will appear again.

SF2_MAIN_Vxxxx.img

ADJ-3

1. Display the CAT mode (Refer to Section 1 - 3.1.)

2.  The CAT mode menu appears on the screen. Select the [CD Mode] menu with [pq] buttons and press the [MUTE] button 

for more than 3 seconds to enter the CD mode.

Main CPU firmware version

1. Press [SETUP] button on remote controller.

2.  The Setup menu appears on the screen. Select the [Language] menu with [pq] buttons and press the [Enter] button.

3.  The Options menu appears on the screen. Select the [Display software information] menu with [pq] buttons and press the 

[MUTE] button for more than 3 seconds to enter the CD mode.

ADJ-4

1. Computer : Used for firmware transforming

2.  Communication cable : D-sub 9pin (female/female RS-232C straight)

3. Software & updating file : SerialLoader & firmware (LF8_80-LFV6_60_SUB_Vxxxx.ldr), 

                                              download from service web site.

4. Extract the software and file package to your favorite directory on your computer. 

5.  Connect the serial terminal (SERIAL-IN) and PC with an RS-232C cable.

Caution: Before performing the updating, the serial cable on the SERIAL OUT terminal must be disconnected
               when using the  "Serial daisy chain" function.  (If did, the display will not turn on again.)  

1. Start up the updating software [SerialLoader.exe].

2.  Choose available COM port with pull down menu and click [OK]. The baudrate should be used with "115200".

3.  On the left window, browse and select a folder where the updating file is stored. The firmware file is listed on the right win-

dow and select it then click [Add]. The selected firmware will listed on the bottom window.

4. Click [OK]. The another confirmation window will appear and then click [OK] to start updating.

5. After finishing the updating, the window below appear and click [OK] to close the software.

6.  Turn the display off and leave for more than 1 minute and then turn on again.Enter the ser-

vice mode [CD Mode] and confirm that the version has been updated.

*   During updating, Do not disconnect 

the AC cord or serial cable otherwise 

the Display may not turn on 

   SAMPLE

   SAMPLE

ADJ-5

1. Display the CAT mode (Refer to Section 1 - 3.1.)

2.  The CAT mode menu appears on the screen. Select the [CD Mode] menu with [pq] buttons and press the [MUTE] button 

for more than 3 seconds to enter the CD mode.

Sub CPU firmware version

1. Press [SETUP] button on remote controller.

2.  The Setup menu appears on the screen. Select the [Language] menu with [pq] buttons and press the [Enter] button.

3.  The Options menu appears on the screen. Select the [Display software information] menu with [pq] buttons and press the 

[MUTE] button for more than 3 seconds to enter the CD mode.