DOWNLOAD Panasonic TC-51P100G / TC-51P100H Service Manual ↓ Size: 22.29 MB | Pages: 127 in PDF or view online for FREE

- 17 -

Outline : MPU controls the functions switching for each ICs through IIC bus in E3D chassis. The following setting

and adjustment can be adjusted by remote control in Market Mode.

If the memory IC ( IC1102 ) is replaced, optional code should be re-memorized. Option code can be changed by pressing Volume
"+" or "-" button. To memorize, press " 0 " of 10 key button. 

CHK5

PTV

ADJUSTMENT

CHK1

PICTURE

ADJUSTMENT

DEFELECTION

ADJUSTMENT

NORMAL MODE

MARKET MODE

Exit : Turn the power

off

OPTION

CHK2

CHK6

CHK4

PIP

ADJUSTMENT

WHITE

BALANCE

ADJUSTMENT

CHK3

1. Selection of Market Mode

Adjust VOLUME "zero" and set OFF TIMER Button [

] (turn on the off timer).

Then, simultaneously press the RECALL[

] Button on the remote control and the VOLUME DOWN button [ - ]

on the TV set.

2. Selection of CHK Mode

Cursor moves each CHK mode by pressing " " or " " of

10 key button on the remote control.

2

2

2

2

2

2

1

1

2

1

1

1

1

1

OPTION

OP1

81

OP2

E2

OP3

DE

OP4

F3

OP5

84

OP6

FF

OP7

73

OP8

02

To memorize, 
press "0" of 
10 key button.

CHK1

OPTION

OP1

81

OP2

E2

OP3

DE

OP4

F3

OP5

84

OP6

FF

OP7

00

OP8

02

- 18 -

1

RF AGC

0~127

76

RF AGC (For Main Picture)

2

CONTRAST

0~63

58

Contrast (the same as user control)

3

SUB CONTRAST

0~63

30

Sub Contrast

4

COLOUR

0~63

32

Colour (the same as user control)

5

SUB COLOUR

0~63

40

Sub Colour (for 3.58 MHz)

6

NTSC TINT

0~63

32

NTSC TINT (the same as user control)

7

SUB NTSC TINT

-128~127

-12

Sub NTSC TINT

8

VIDEO GAIN

0~255

153

Video Gain

9

OSD POSITION

0~20

6

On-Screen Display Position

10

DVCO ADJ

-1~1

0

DVCO Adjustment

1

BRIGHT

0~63

32

Bright (the same as user control)

2

SUB BRIGHT

0~63

48

Sub Bright

3

PTV EHT  PROTECT

0

0

PTV EHT Protect

1

SUB CONTRAST 2

0~255

216

Sub Contrast 2

2

SUB NTSC-TINT 2

-128~127

-11

Sub NTSC TINT 2

3

DVCO ADJ 2

-1~1

0

DVCO Adjustment 2

- 19 -

1

100Hz H-WIDTH

0~63

36

Horizontal Width (50Hz)

2

100Hz EW-PARABOLA

0~63

40

EW-Parabola (50Hz)

3

100Hz EW-CORNER

0~63

9

EW-Corner (50Hz)

4

100Hz V-HEIGHT

0~63

54

Vertical Height (50Hz)

5

100Hz V-S-CORRECT

0~63

4

Vertical Scurve Correction (50Hz)

6

100Hz H-CENTER

0~63

35

Horizontal Center (50Hz)

7

100Hz V-CENTER

0~63

37

Vertical Center (50Hz)

8

100Hz TRAPEZOID

0~63

27

Trapezoid (50Hz)

9

100Hz H-PARARELL

0~63

32

Horizontal Parallel (50Hz)

10

PTV S CONVERGENCE

-----

-----

Into Static Convergence

1

PTV G-GAIN

0~255

192

PTV Green Gain

2

PTV R-GAIN

0~255

125

PTV Red Gain

3

PTV B-GAMMA ST1

0~255

152

PTV Blue Gamma ST1

4

PTV B-GAMMA-GAIN

0~255

76

PTV Blue Gamma Gain

5

PTV B-GAIN

0~255

65

PTV Blue Gain

6

PTV R-CUTOFF

0~255

98

PTV Red Cutoff

7

PTV G-CUTOFF

0~255

128

PTV Green Cutoff

8

PTV B-CUTOFF

0~255

163

PTV Blue Cutoff

9

PTV B-LIMIT

0~255

154

PTV Blue Limit

- 20 -

+B Voltage Confirmation
1. Operate the set.
2. Set controls:

Bright..........................minimum
Contrast......................minimum
Volume........................minimum

Confirm the following voltages.
  1. Pin 1 of connector D3          : 207.0±3.0V
  2. Pin 4 of connector D12        : 130.0±2.0V
  3. Pin 8 of connector D12        : 26.0±2.0V
  4. Pin 1 of connector D13        : 15.5±1.5V
  5. Pin 5 of connector D13        : 15.5±1.5V
  6. Pin 1 of connector D11        : 9.0±1.5V
  7. Pin 7 of connector D3          : 6.4±0.24V
  8. Pin 8 of connector D13        : -15.5±1.5V
  9. Pin 3 of connector D3          : 12.0±0.5V
10. Pin 1 of connector D14        : 40.0±2.0V (open)
                                                   : 32.0±2.0V (short)
11. Pin 8 of connector D11         : 6.5±1V
12. TPCP1  :  22±2V
13. TPCP2  :  -22±2V
14. TPCP3  :  14±1.5V
15. TPCP4  :  -14±1.5V

RF AGC (Main picture) (MARKET MODE CHK2)
1. Receive a colour bar pattern.
2. Set the input level to 

62dB (+1/-2 dB)
(75

:

 opened)

3. Connect an oscilloscope to TPA1 with DC mode.

1. Set the TV to MARKET MODE [CHK2 mode].
2. Adjust RF AGC Control so that the voltage at TPA1 becomes 6.2 ±

0.5V.

3. Increase the input level by 2dB and confirm that the voltage

changes.

RF AGC 2 (Sub picture) 
1. Receive a colour bar pattern.
2. Set the input level to 

70dB (+1/-2 dB)
(75

:

 opened)

3. Connect an oscilloscope to TPA8 with DC mode.

1. Adjust TNR002 so that the volt-

age at TPA8 becomes 6.2 ±
0.5V.

2. Increase the input level by 2dB

and confirm that the voltage
changes.

PAL Colour Output
1. Receive PAL colour bar pattern.
2. Connect an oscilloscope to TPA14 (A-Board).
3. Connect a 22k

:

 jumper between TPA50 and TPA51 (A-

Board).

4. Set controls:

Picture menu..........DYNAMIC NORMAL
P.AI........................OFF
PWL.......................OFF

1. Adjust Sub Colour control.

NTSC Colour Output 
1. Apply 3.58MHz NTSC Rainbow pattern.
2. Connect an oscilloscope to TPA13 (A-Board).
3. Connect a 22 k

:

 jumper between TPA50 and TPA51 (A-

Board).

4. Set controls : 

Picture menu..........DYNAMIC NORMAL
P.AI.........................OFF
PWL........................OFF

1. Confirm that the waveform:

SECAM Colour Output
1. Receive SECAM colour bar pattern.
2. Connect an oscilloscope to TPA14(A-Board).
3. Connect a 22k

:

 jumper between TPA50 and TPA51(A-Board).

4. Set controls : 

Picture menu..........DYNAMIC NORMAL
P.AI.........................OFF
PWL........................OFF

1. Confirm that the waveform:

Adjust

TNR002

(Top View)

A=2.40 ± 0.05

1 2 3 4 5 6 7 8 910

A=1.9 ± 0.2Vp-p

A=2.0 ± 0.2Vp-p