Panasonic KX-TGJ310RU / KX-TGJ312RU / KX-TGJ320RU / KX-TGJ322RU / KX-TGJA30RU Service Manual ▷ View online
17
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
4.6.
Signal Route
Note:
: inside of Handset
*1: KX-TGJ320 only
*1
*1
*1
*1
---ANT. - <BASE_UNIT_RF_RX_ROUTE> - IC501(1/2 - 21) - C184 - Q161 - Q141
- D101 - P101 - T/R(TEL LINE)
- D101 - P101 - T/R(TEL LINE)
T/R(TEL LINE) - P101 - D101 - Q141 - Q161 - R164 - C173 - R178
- IC501(19-86/87) - <BASE_UNIT_RF_TX_ROUTE> - ANT. ---
- IC501(19-86/87) - <BASE_UNIT_RF_TX_ROUTE> - ANT. ---
---ANT. - <BASE_UNIT_RF_RX_ROUTE> - IC501(1/2 - 21) - C184 - Q161 - Q141
- D101 - P101 -T/R(TEL LINE)
- D101 - P101 -T/R(TEL LINE)
T/R(TEL LINE) - P101 - D101 - Q141 - Q161 - R164 - C173 - R178
- IC501(19-86/87) - <BASE_UNIT_RF_TX_ROUTE> - ANT. ---
- IC501(19-86/87) - <BASE_UNIT_RF_TX_ROUTE> - ANT. ---
---ANT. - <BASE_UNIT_RF_RX_ROUTE> - IC501(1/2- 58/60) - IC601
IC601 - IC501(58/60 - 21) - C184 - Q161 - Q141 - D101 - P101
- T/R(TEL LINE)
- T/R(TEL LINE)
T/R(TEL LINE) - P101 - D101 - Q141 - Q161 - R164 - C173-R178
- IC501(19 - 58/60) - IC601
- IC501(19 - 58/60) - IC601
IC601 - IC501(58/60 - 35/37) - SPEAKER
IC501(21) - C184 - Q161 - Q141 - D101 - P101 - T/R(TEL LINE)
T/R(TEL LINE) - P101 - C105/C106 - R103/R104 - IC501(15/18)
T/R(TEL LINE) - P101 - C105/R103 - C110/R110-R111-C111/R112 - IC501
HANDSET TX
HANDSET RX
HANDSET
SP-Phone TX
SP-Phone TX
HANDSET
SP-Phone RX
SP-Phone RX
SIGNAL ROUTE
IN
䊻㻌
ROUTE
䊻㻌
OUT
GREETING
RECORDING
RECORDING
GREETING PLAY
TO TEL LINE
TO TEL LINE
ICM RECORDING
ICM PLAY TO
SPEAKER
SPEAKER
DTMF SIGNAL
TO TEL LINE
TO TEL LINE
CALLER ID
BELL DETECTION
MIC (+) -
C13
-
IC1 (17)
IC1(86)
MIC (–) -
C11
-
IC1 (18)
IC1(87)
C859
- ANT to BASE
from BASE UNIT ANT 1
IC1 (1)
IC1 (2)
IC1 (2)
IC1 (21) - RECEIVER (+)
IC1 (22) - RECEIVER (–)
IC1 (22) - RECEIVER (–)
MIC (+) -
C13
-
IC1 (17)
IC1(86)
MIC (–) -
C11
-
IC1 (18)
IC1(87)
C859
- ANT to BASE
from BASE UNIT ANT –– IC1 (1) ––– IC1 (35) - SP (–)
– IC1 (2) – – IC1 (37) - SP (+)
MIC (+) -
C13
-
IC1 (17)
IC1(86)
MIC (–) -
C11
-
IC1 (18)
IC1(87)
C859
- ANT to BASE
RA4
-
RA4
-
RA4
-
RA4
-
RA4
-
RA4
-
18
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
RF part signal route
SIGNAL ROUTE
IN
䊻㻌
ROUTE
䊻㻌
OUT
HANDSET RF
[ TX_ROUTE ]
[ TX_ROUTE ]
HANDSET RF
[ RX_ROUTE ]
[ RX_ROUTE ]
BASE UNIT RF
[ TX_ROUTE ]
[ TX_ROUTE ]
BASE UNIT RF
[ RX_ROUTE ]
[ RX_ROUTE ]
IC1(86/87) - C859 - ANT
ANT - IC(1/2)
IC501(86/87) - C859 - DA802--- C853-ANT2
ANT2 - C853 --- DA802-IC501(1/2)
ANT1 - C851 --
ANT1 - C851 --
Note:
: inside of Handset
C851-ANT1
19
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
5 Location of Controls and Components
Refer to the Operating Instructions.
Note:
You can download and refer to the Operating Instructions (Instruction book) on TSN Server.
6 Installation Instructions
Refer to the Operating Instructions.
Note:
You can download and refer to the Operating Instructions (Instruction book) on TSN Server.
7 Operating Instructions
Refer to the Operating Instructions.
Note:
You can download and refer to the Operating Instructions (Instruction book) on TSN Server.
7.1.
For Service Hint
(right soft key)
132
Items
Contents
Battery
You could use other rechargeable batteries sold in a market, but the unit is not guaranteed to work
properly.
properly.
The battery strength may not be indicated correctly if the battery is disconnected and connected again,
even after it is fully charged. In that case, by recharging the battery as mentioned in the Operating
Instructions, you will get a correct indication of the battery strength.
even after it is fully charged. In that case, by recharging the battery as mentioned in the Operating
Instructions, you will get a correct indication of the battery strength.
PIN Code
Recall
Earth Recall feature is not supported in this model.
L Change the PIN using the following method.
1
2
2
7
3
Enter the new 4-digit base unit PIN.
i
{OK}
#
4
{ ^^ } : “ Yes”
i
{OK}
i
{
c
}
}
20
KX-TGJ310/KX-TGJ312/KX-TGJ320/KX-TGJ322/KX-TGJA30
8 Test Mode
8.1.
Engineering Mode
8.1.1.
Base Unit
Important:
Make sure the address on LCD is correct when entering new data. Otherwise, you may ruin the unit.
C
C
OK
OK
OK
TUV
ШЩЪЫ
8
WXYZ
ЬЭ ЮЯ
9
ФХ ЦЧ
7
PQRS
ABC
АБВГ
2
ДЕ ЖЗ
DEF
3
GHI
ИЙ К Л
4
MNO
РСТУ
6
JKL
МН ОП
5
0
1
This pictured model is KX-TGJ320.
/ECO
Dial keypad
9). Press
to return to standby mode.
After that, turn the base unit power off and then power on.
2). Select "Initial Setup" using or
then press
then press
{
OK
}
.
H/S key operation
{^}
4). Enter "7", "2", "6", "2", "7", "6", "6", "4".
Note: 7262 7664 = PANA SONI
(see letters printed on dial keys)
6). Enter " ", " ", " ", " " (Address). (*1)
7). Enter " ", " " (New Data). (*1)
5). Select "Write EEP" using or
then press
then press
or
{>}
.
{^}
3). Select "Line Setup" using or
then press
{
OK
}
or
{>}
.
{^}
_ _ _ _ _ _
H/S LCD
Set Addr.:
Default Data
Set Addr.:
New Data
Set Addr.:
8). Press , a long confirmation beep
will be heard.
{
OK
}
Service Mode
Read EEP
Write EEP
{
OK
}
Get S/W Ver.
{ }
{
}
Soft keys
(Volume) key/
(Phonebook)/
(Caller list) key/
(Redial) key/
Navigator key/
1). Press
{
}
(Off/Power)
R
R: Recall/Flash
ECO: Eco mode shortcut key
ECO: Eco mode shortcut key
(Talk)
{
}
{ }(Intercom)
{ } (Off/Power)
{V}
{V}
{V}
Click on the first or last page to see other KX-TGJ310RU / KX-TGJ312RU / KX-TGJ320RU / KX-TGJ322RU / KX-TGJA30RU service manuals if exist.