DOWNLOAD Panasonic KX-TG8551CAB / KX-TG8561CAB / KX-TGA855RUB Service Manual ↓ Size: 8.49 MB | Pages: 103 in PDF or view online for FREE

45

(F)* Battery Monitor Check

-

1. Apply 2.25 V between BATT+ and BATT-.
2. Execute the command 

sendchar PAD
sendchar LED 0
sendchar CRX 0 1
sendchar AD1
It assumes that the return value is XX.
a) XX: 70: No need to adjust
b) XX: 66 ~ 6F: Need to adjust
XX: 71 ~ 7A: Need to adjust
Write AD value of 2.25 V to EEPROM.
ex) read data: XX = 6A, write data: YY = 6A
read data: XX = 73, write data: YY = 73
EEPROM = 0009(Low Voltage) write “YY”
Execute the command “wreeprom 00 09 01 YY”.
EEPROM = 000A(No Voltage) write “YY -C"
Execute the command “wreeprom 00 0A 01 ZZ”.
for model with Power Failure Talk, add:

EEPROM = 000B (Low Voltage for PSPLY)
Write YY + A
Execute the command "wreeprom 00 0B 01 XX".

XX = YY + A
ZZ = YY - C

c) XX: 00 ~ 65: Reject
XX: 7B ~ FF: Reject

IC1, F1, R45

(G)

Battery Low 

Confirmation

-

1. Apply 2.40 V between BATT+ and BATT-.
2. Confirm that there is no flashing of Battery Icon.
3. Apply 2.25 V ± 0.08 V between BATT+ and BATT-.
4. Confirm that there is flashing of Battery Icon.

IC1, F1, R45

(H)* BBIC Clock Adjustment

CKM

1. Apply 2.6 V between BATT+ and BATT- with DC power.
2. Input Command “sendchar sfr”, then you can confirm the current value.
3. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
4. If the frequency is not 10.368 MHz ± 100 Hz, adjust the frequency of CKM

executing the command “sendchar sfr xx xx (where xx is the value)” so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.

Note:

Clear the registered information for Base Unit before measurement, because the
Frequency will not possibly get stable due to the registered information.
Pressing the button of "3" "5" "7" "#"clears the registration.
Register to it on Base Unit after measurement. 

IC1, X1, C47

 

(I)*

Transmitted Power 

Confirmation

-

Short Antenna pattern to GND.

1. Configure the DECT tester (CMD60) as follows;

<Setting>

• Test mode: PP
• RFPI: 0102030405
• Traffic Carrier: 5
• Traffic Slot: 4
• Mode: Loopback
• RF LEVEL = -70 dBm
• PACKET: PP32Z

2. Execute the command “sendchar TST 01 02 03 04 05".
3. Initiate connection from DECT tester.
4. Confirm that the NTP value at ANT is 19 dBm ~ 25 dBm.

IC1, 

C802~C806, 
C809~C814, 
C820, C822, 

C823, 

C825~C826, 

L802, L803, 

DA801, R806, 

R807

(J)* Modulation Check and 

Adjustment

-

Follow steps 1 to 3 of (I).

4.Confirm that the B-Field Modulation is -350 ± 50/+350 ± 50 kHz/div using data
type Fig 31.

Refer to (I)

(K)*

Frequency Offset 

Confirmation

-

Follow steps 1 to 3 of (I).

4.Confirm that the frequency Offset is < ± 20 kHz.

Refer to (I)

(L)*

Sensitivity Receiver 

Confirmation

-

Follow steps 1 to 3 of (I).

4.Set DECT tester power to -88 dBm.
5.Confirm that the BER is < 1000 ppm.

Refer to (I)

(M)*

Power RAMP 

Confirmation

-

Follow steps 1 to 3 of (I).

4.Confirm that Power RAMP is matching.

Refer to (I)

Items

Check 

Point

Procedure

Check or 

Replace Parts

46

(N)

Audio Check and 

Confirmation

-

1. Link to BASE which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 50 mA.
3. Input -45 dBm (600 

Ω)/1 kHz to MIC of Handset. Measure the Level at Line I/F

and distortion level.

4. Confirm that the level is -2.0 dBm ± 5 dB and that the distortion level is < 5 %

at TEL Line (600 

Ω Load).

5. Input -20 dBm (600 

Ω)/1 kHz to Line I/F. Measure the Level at Receiver of

Handset and distortion level (Receive volume set to second position from
minimum).

6. Confirm that the level is -30.0 dBm ± 4 dB and that the distortion level is < 5 %

at Receiver (34 

Ω Load).

IC1, C12, C96, 

C97, R5, R27, 

RA4, C11, 
C13, R28, 
MIC, R23, 

C42, C70, C71

(O) SP phone Audio Check 

and Confirmation

-

1. Link to Base which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 50 mA.
3. Set the handset off-hook using SP-Phone key.
4. Input -30 dBm (600 

Ω)/1 KHz to Line I/F and measure Receiving level at SP+

and SP-.

5. Confirm that the level is -8.0 dBm ± 3 dB and that the distortion level is < 5 %. 

(vol = Max at SP (8 

Ω Load))

IC1, D13, D14, 

C72, C73, 
C98, C99, 
C78, C79, 

R76, R77

(P)

Charge Pump 3.0 V 

Supply Confirmation

CP3V

1. Confirm that the voltage between testpoint CP3.0V and GND is 3.0 V ± 0.3 V. C30, C53, C54

(Q) Charge Pump CP_LED 

4.0V Supply 

Confirmation

CP_LED

1. Confirm that the voltage between testpoint CP_LED and GND is 4.0 V ± 0.3 V.

(Power is supplied when LED in on)

C52, C55 

(R)

Charge Pump CP2.8V

Supply Confirmation

CP2.8V

1. Confirm that the voltage between testpoint CPV2.8V and GND is 2.8V ± 0.3 V.

C30, C53, 

C54, D3, C51 

(S)

Headset Audio Check 

and Confirmation

-

1. Link to Base which is connected to Line Simulator.
2. Set line voltage to 48 V and line current to 50 mA.
3. Input -45 dBm (600 

Ω)/1 kHz to MIC of Headset. Measure the Level at Line I/F

and distortion level.

4. Confirm that level is -10.0 dBm ± 3 dB and that the distortion level is < 5 % at

TEL Line (600 

Ω Load).

5. Input -20 dBm (600 

Ω)/1 KHz to Line I/F. Measure the Level at Receiver of

Headset and distortion level (Receive volume set to second position form
minimum).

6. Confirm that the level is -22.5 dBm ± 3 dB and that the distortion level is < 5 %

at Headset Receiver (150 

Ω Load). 

IC1, R29, C37, 

R22, C14, 
R25, C16, 

C83, R80, L7, 
L9, C87, C84, 

CN4, C80, 

C82, C39, L10, 

L8 

Items

Check 

Point

Procedure

Check or 

Replace Parts

47

When the customer’s telephone line corresponds to the following conditions, and the transmission signal of SP-Phone is
interrupted, performing the next set up to a cordless handset will improve it to some extent.
Conditions

1. When customer’s line has less line loss.

ex.) The customer is using optical fiber, ISDN terminal adaptor, or PBX.
In this case, receiving signal is strong and it may affect transmission signal.

2. When the other party is talking from noisy place.

ex.) The other party is using cellular phone. The background noise is very loud.
In this case, the noise from the other party (i.e. surrounding noise) may affect transmission signal.

* Do not enter New Data if the Default Data is different from the table above.

(*1) Refer to Handset (P.22) of Engineering Mode to enter the Address or New Data. 

TGA855 

TX 6dB Louder

02 EC
02 ED

02 E8
02 E9

02 EA
02 EB

F5
32

FC

5F
01
00

8A

19

FC

5F
02
00

TX 12dB Louder

02 EC
02 ED

02 E8
02 E9

02 EA
02 EB

F5
32

FC

5F
01
00

CC
CC

FC

5F
03
00

TX 6dB Lower

02 EC
02 ED

02 E8
02 E9

02 EA
02 EB

F5
32

FC

5F
01
00

AC

65

FC

5F
00
00

48

Ԙ

ԙ

4 screws

Solders

Cabinet 
cover