Panasonic KX-TG8411RUB / KX-TG8411RUN / KX-TG8411RUT / KX-TG8411RUW / KX-TG8412RUT / KX-TGA840RUB / KX-TGA840RUN / KX-TGA840RUT / KX-TGA840RUW Service Manual ▷ View online
65
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
11.5.2. How to install Batch file into P.C.
Note:
• “*****” varies depending on the country or models.
11.5.3. Commands
See the table below for frequently used commands.
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
98” is written.
getchk
Read checksum
Type “getchk”.
wreeprom
Write the data of EEPROM
Type “wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
is data to be written.
66
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
11.6. Adjustment Standard (Handset)
When connecting the simulator equipments for checking, please refer to below.
11.6.1. Component View
Note:
(A) - (R) is referred to Check Point (Handset) (P.52)
(A) - (R) is referred to Check Point (Handset) (P.52)
A
PbF
PNLB1104Z
KX-TGA840XX EU
C138
C71
C152
C70
RECEIVER
C139
SPEAKER
C29
C802
C72
C813
C811
C804
C73
C147
C121
C5
C3
F1
C76
C77
C113
C54
C40
C40
C44
C834
C814
C863C864
C43
C47
C83
C185
C35
C39
C110
4
5
1
X_CLK
POWER
1.8V
C128
C2
C1
C172
CP4.0V
CP2.5V
C111
C33
C6
C7
C837
C14
C13
C38
C332
C51
C55
C53
C52
C49
R71
R209
R208
R63
R66
R64
R225
R802
R805
R6
R74
R73
R31
R7
R30
R4
R8
R45
R300
R303
R301
R302
R305
R12
R42
R41
R41
R40
R32
R33
R25
R203
R807
R22
R28
R332
R330
R331
R306
R304
R20
R307
L804
L802
L3
L9
L72
L73
L74
L71
IC1
TEST
JT A
G
RA61
BA TT
-
BA TT+
RA4
D21
D22
D14
D13
BLK
RED
BLK
RED
D8
D7
D4
D3
Q4
Q7
Q11
Q12
Q2
C45
C36
C46
C860
C182
C819
C825
C827
C809
C810
C805
C808
C861
C812
C859
C862
C803
C806
CN4
C74
C75
C4
C15
C150
C188
C97
C96
C822
C826
C41
X1
C820
C18
C11
C10
C12
C16
C331
C184
C17
C48
C50
C109
C82
3
2
1
14
85
1
C108
C86
C127
R65
R808
R801
R806
R803
R804
SP-PHONE_SPEAKER
R310
R309
R2
R215
R27
R152
R34
R308
R100
L801
L803
L5
L4
L8
IC801
IC3
RA1
RA2
D
A801
D1
Q9
UTX
URX
GND
CHG (-)
CHG (+)
BA T
MIC-
MIC+
OSC
AF V
O
LT
METER
LOOP
Sim
ulator
Dumm
y Base
Unit
6.3
V 47 F
6.3
V 47 F
AF
GENERA
T
O
R
DC
6.5V
DC PO
WER
2.30-2.60V
DC PO
WER
2.00-2.25V
GND
Digital
V
olt Meter
UTX
URX
GND
PC
GND
CLK
F
requency
Counter
2.7 V
Zener
AF
OSC
MIC-
(D),(E),(F),(G)
(A),(B),(C),(F),(G),(H),(I)
(A),(Q),(R)
iH)
(I),(J),(K),(L),(M),(N)
(O),(P)
(O)
(O),(P)
MIC+
+
+
600
100
GND
ANT
DECT T
ester
CMD60
(at batter
y lo
w)
PO
WER KEY
150
56
56
SP+
REV-
REV+
SP-
8
1 F
AF V
O
LT
METER
Oscilloscope
A
B
1
22pF
Current
Probe
Oscilloscope
1.8V
CP 2.5V
CP 4.0V
67
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
11.7. Things to Do after Replacing IC or X'tal
If repairing or replacing BBIC (FLASH type), EEPROM and X'tal, it is necessary to download the required data such as Program-
ming data or adjustment data, etc in memory.
The set doesn't operate if it is not executed.
ming data or adjustment data, etc in memory.
The set doesn't operate if it is not executed.
11.7.1. How to download the data
11.7.1.1. Base Unit
First, operate the PC setting according to The Setting Method of JIG (Base Unit)(P.60).
Then download the appropriate data according to the following procedures.
Then download the appropriate data according to the following procedures.
Note:
(*1) XX: country code, YY: revision number, ZZ: Voice Prompt
“XX”, “YY” and “ZZ” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (Base Unit) (P.60).
(*2) Refer to Check Point (Base Unit) (P.48)
“XX”, “YY” and “ZZ” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (Base Unit) (P.60).
(*2) Refer to Check Point (Base Unit) (P.48)
Items
How to download/Required adjustment
BBIC (FLASH type)
(IC7)
(IC7)
Programming data is stored in memory.
1) Make sure to connect the JIG cable, then disconnect the DC
Power in order to download the data.
2) Execute the command “flw480 *********.hex”.
3) Connect the DC Power.
4) Press the PC Enter key once.
5) After a few minutes, “Successful upgrade” is displayed on the
PC indicating downloading has finished.
6) Detach the JIG cable, then disconnect the DC Power.
7) Connect the DC Power.
8) Connect the JIG cable again, and execute the command
“getchk”, then confirm the checksum value is correct.
Power in order to download the data.
2) Execute the command “flw480 *********.hex”.
3) Connect the DC Power.
4) Press the PC Enter key once.
5) After a few minutes, “Successful upgrade” is displayed on the
PC indicating downloading has finished.
6) Detach the JIG cable, then disconnect the DC Power.
7) Connect the DC Power.
8) Connect the JIG cable again, and execute the command
“getchk”, then confirm the checksum value is correct.
• If the downloading fails, start again from step 1).
9) Default batch file: Execute the command “default.bat”.
10) Country version batch file: Execute the command
“TG8411XXrevYY.bat”. (*1)
11) Clock adjustment: Refer to Check Point (G). (*2)
10) Country version batch file: Execute the command
“TG8411XXrevYY.bat”. (*1)
11) Clock adjustment: Refer to Check Point (G). (*2)
EEPROM (IC401)
Adjusted parameter data is stored in memory.
(country version batch file, default batch file,
etc.)
(country version batch file, default batch file,
etc.)
1) Change the address “0000” of EEPROM to “AA” to download
the data.
2) Default batch file: Execute the command “default.bat”.
3) Country version batch file: Execute the command
“TG8411XXrevYY.bat”. (*1)
4) Clock adjustment: Refer to Check Point (F). (*2)
the data.
2) Default batch file: Execute the command “default.bat”.
3) Country version batch file: Execute the command
“TG8411XXrevYY.bat”. (*1)
4) Clock adjustment: Refer to Check Point (F). (*2)
X'tal (X1)
System clock
Clock adjustment data is in EEPROM, adjust the data again
after replacing it.
1) Refer to Check Point (F). (*2)
after replacing it.
1) Refer to Check Point (F). (*2)
68
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
11.7.1.2. Handset
First, operate the PC setting according to The Setting Method of JIG (Handset)(P.64).
Then download the appropriate data according to the following procedures.
Then download the appropriate data according to the following procedures.
Note:
(*3) XX: country code, YY: revision number
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (Handset) (P.64).
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (Handset) (P.64).
(*4) Refer to Check Point (Handset) (P.52)
Items
How to download/Required adjustment
BBIC (FLASH type)
(IC1)
(IC1)
Programming data is stored in memory.
1) Make sure to connect the JIG cable, then disconnect the DC
Power in order to download the data.
2) Execute the command “flw480 *********.hex”.
3) Connect the DC Power.
4) Press and hold the handset Power key.
5) While holding down the handset Power key, press the PC
Enter key once.
6) After a few minutes, “Successful upgrade” is displayed on
the PC indicating downloading has finished.
7) Detach the JIG cable, then press the handset Power key to
turn it on.
8) Connect the JIG cable again, and execute the command
"getchk”, then confirm the checksum value is correct.
Power in order to download the data.
2) Execute the command “flw480 *********.hex”.
3) Connect the DC Power.
4) Press and hold the handset Power key.
5) While holding down the handset Power key, press the PC
Enter key once.
6) After a few minutes, “Successful upgrade” is displayed on
the PC indicating downloading has finished.
7) Detach the JIG cable, then press the handset Power key to
turn it on.
8) Connect the JIG cable again, and execute the command
"getchk”, then confirm the checksum value is correct.
• If the downloading fails, start again from step 1).
10) Default batch file: Execute the command “default.bat”.
11) Default batch file (remaining): Execute the Command
“TGA840DEFrevYY.bat”. (*3).
12) Country version batch file: Execute the command
“TGA840XXrevYY.bat”. (*3).
13) Clock adjustment: Refer to Check Point (H). (*4).
14) 1.8 V setting and battery low detection: Refer to Check
Point (A), (F) and (G). (*4).
11) Default batch file (remaining): Execute the Command
“TGA840DEFrevYY.bat”. (*3).
12) Country version batch file: Execute the command
“TGA840XXrevYY.bat”. (*3).
13) Clock adjustment: Refer to Check Point (H). (*4).
14) 1.8 V setting and battery low detection: Refer to Check
Point (A), (F) and (G). (*4).
EEPROM (IC3)
Adjusted parameter data is stored in memory.
(country version batch file, default batch file,
etc.)
(country version batch file, default batch file,
etc.)
1) Default batch file: Execute the command “default.bat”.
2) Default batch file (remaining): Execute the Command
“TGA840DEFrevYY.bat”. (*3)
3) Country version batch file: Execute the command
“TGA840XXrevYY.bat”. (*3)
4) Clock adjustment: Refer to Check Point (J). (*4)
5) 1.8 V setting and battery low detection: Refer to Check Point
(A), (F) and (G). (*4)
2) Default batch file (remaining): Execute the Command
“TGA840DEFrevYY.bat”. (*3)
3) Country version batch file: Execute the command
“TGA840XXrevYY.bat”. (*3)
4) Clock adjustment: Refer to Check Point (J). (*4)
5) 1.8 V setting and battery low detection: Refer to Check Point
(A), (F) and (G). (*4)
X'tal (X1)
System clock
Clock adjustment data is in EEPROM, adjust the data again
after replacing it.
1) Refer to Check Point (H). (*4)
after replacing it.
1) Refer to Check Point (H). (*4)
Click on the first or last page to see other KX-TG8411RUB / KX-TG8411RUN / KX-TG8411RUT / KX-TG8411RUW / KX-TG8412RUT / KX-TGA840RUB / KX-TGA840RUN / KX-TGA840RUT / KX-TGA840RUW service manuals if exist.