Panasonic KX-TG8411RUB / KX-TG8411RUN / KX-TG8411RUT / KX-TG8411RUW / KX-TG8412RUT / KX-TGA840RUB / KX-TGA840RUN / KX-TGA840RUT / KX-TGA840RUW Service Manual ▷ View online
45
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
9.1.4.3.
Check Table for RF part
Note:
(*1) Refer to Adjustment Standard (Base Unit) (P.62)
(*2) Refer to Adjustment Standard (Handset) (P.66)
(*2) Refer to Adjustment Standard (Handset) (P.66)
No.
Item
BU (Base Unit) Check
HS (Handset) Check
1
Link Confirmation Normal
HS, BU Mode: [Normal mode]
1. Register Regular HS to BU (to be
checked).
2. Press [Talk] key of the Regular HS to
establish link.
1. Register HS (to be checked) to Regular
BU.
2. Press [Talk] key of the HS to establish link.
2
X’tal Frequency confirmation
1. Check X’tal Frequency. (*1)
(10.368 MHz ± 100 Hz)
1. Check X’tal Frequency. (*2)
(10.368 MHz ±100Hz)
3
Range Confirmation Normal
HS, BU Mode: [Normal mode]
1. Register Regular HS to BU (to be
checked).
2. Press [Talk] key of the Regular HS to
establish link.
3. Compare the range of the BU (being
checked) with that of the Regular BU.
1. Register HS (to be checked) to Regular
BU.
2. Press [Talk] key of the HS to establish link.
3. Compare the range of the HS (being
3. Compare the range of the HS (being
checked) with that of the Regular HS.
46
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
9.1.5.
Check Handset Transmission
Cross Reference:
Signal Route (P.14)
9.1.6.
Check Handset Reception
Cross Reference:
How to Check the Handset Speaker or Receiver (P.70).
Signal Route (P.14)
Signal Route (P.14)
9.1.7.
Check Caller ID
Cross Reference:
Signal Route (P.14)
47
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
9.1.8.
Bell Reception
9.1.8.1.
Base Unit
9.1.8.2.
Handset
Cross Reference:
Telephone Line Interface (P.10)
Check Link (P.39)
How to Check the Handset Speaker or Receiver (P.70)
Check Link (P.39)
How to Check the Handset Speaker or Receiver (P.70)
48
KX-TG8411RU//KX-TG8412RU/KX-TGA840RU
9.2.
Troubleshooting by Symptom (Base Unit and Charger Unit)
If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester
(*1) or not.
(*1) or not.
Note:
(*1) A general repair is possible even if you don’t have the DECT tester because it is for confirming the levels, such as Acoustic
level in detail.
(*2) Refer to Check Point (Base Unit) (P.48)
level in detail.
(*2) Refer to Check Point (Base Unit) (P.48)
9.2.1.
Check Point (Base Unit)
Please follow the items below when BBIC or EEPROM or FLASH is replaced.
Note:
After the measuring, suck up the solder of TP.
*: The Setting Method of JIG (Base Unit) (P.60) is required beforehand.
The connections of simulator equipments are as shown in Adjustment Standard (Base Unit) (P.62).
*: The Setting Method of JIG (Base Unit) (P.60) is required beforehand.
The connections of simulator equipments are as shown in Adjustment Standard (Base Unit) (P.62).
Items
Check
Point
Procedure
Check or
Replace Parts
(A) 3.0 V Supply Confirma-
tion
VDD3
1. Confirm that the voltage between test point VDD3 and GND is 3.0 V ± 0.2 V.
IC1, C31, C32,
R38, R39, C36,
F1, C37, D1
(B) 1.8 V Supply Confirma-
tion
VDD1
1. Confirm that the voltage between test point VDD1 and GND is 1.8 V Å} 0.02 V.
2. Execute the command “VDD”, then check the current value.
3. Adjust the 1.8V voltage of VDD1 executing command “VDD XX” (XX is the
2. Execute the command “VDD”, then check the current value.
3. Adjust the 1.8V voltage of VDD1 executing command “VDD XX” (XX is the
value).
Q8, C75, C614,
C61, IC7
(C) Charge Pump
2.5V Supply Confirma-
tion
tion
VDD5
1. Confirm that the voltage between test point VDD5 and GND is 2.5 V -0.1/+0.3
V.
IC7,C625,C631
(D) Charge Pump
3.0V Supply Confirma-
tion
tion
VDD4
1. Confirm that the voltage between test point VDD4 and GND is 3.0 V ± 0.2 V. IC7,C616,C630
(E)*
BBIC Confirmation
-
1. BBIC Confirmation (Execute the command “getchk”).
2. Confirm the returned checksum value.
2. Confirm the returned checksum value.
Connection of checksum value and program number is shown below.
IC7, X1, R77,
RA80
(F)* EEPROM Confirmation
-
1. EEP-ROM Confirmation (Execute the command "sendchar EPV").
2. Confirm the returned Value(Value for reference is written at "EEPROM C/
2. Confirm the returned Value(Value for reference is written at "EEPROM C/
SUM" in Software_Version_Table.xls).
IC7, RA402,
C51, R657,
IC401
(G)* BBIC Clock Adjustment
CLK
1. Input Command “ sendchar WWD ff 48 IC 8006”
2. Confirm that the voltage between testpoint VDD4 and GND is less than 1.0 V.
3. Input Command “ sendchar sfr”, then you can confirm the current value.
4. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
5. If the frequency is not 10.368MHz ± 100Hz, adjust the frequency of CLK exe-
2. Confirm that the voltage between testpoint VDD4 and GND is less than 1.0 V.
3. Input Command “ sendchar sfr”, then you can confirm the current value.
4. Check X’tal Frequency. (10.368 MHz ± 100 Hz).
5. If the frequency is not 10.368MHz ± 100Hz, adjust the frequency of CLK exe-
cuting the command “sendchar sfr xx xx (where xx is the value)” so that the
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
reading of the frequency counter is 10.368000 MHz ± 5 Hz.
X1, IC7, R430,
C305
Click on the first or last page to see other KX-TG8411RUB / KX-TG8411RUN / KX-TG8411RUT / KX-TG8411RUW / KX-TG8412RUT / KX-TGA840RUB / KX-TGA840RUN / KX-TGA840RUT / KX-TGA840RUW service manuals if exist.