DOWNLOAD Panasonic KX-TG8151RUB / KX-TG8151UAB / KX-TG8151CAB / KX-TG8161RUB / KX-TG8161UAB / KX-TG8161CAB / KX-TGA815RUB Service Manual ↓ Size: 7.53 MB | Pages: 102 in PDF or view online for FREE

9

Base Unit consists of the following ICs as shown in Block Diagram (Base Unit) (P.8).

• DECT BBIC (Base Band IC): IC501

- Handling all the audio, signal and data processing needed in a DECT base unit
- Controlling the DECT specific physical layer and radio section (Burst Module Controller section)
- ADPCM code filter for speech encoding and speech decoding (DSP section)
- Echo-cancellation and Echo-suppression (DSP section)
- Any tones (tone, sidetone, ringing tone, etc.) generation (DSP section)
- DTMF receiver (DSP section)
- Clock Generation for RF Module
- ADC, DAC, timer, and power control circuitry
- PLL Oscillator
- Detector 
- Compress/Expander
- First Mixer
- All interfaces (ex: QSPI FLASH MEMORY, EEPROM, LED, Analog Front End, etc.)
- Integrated 1.9GHz PA for DECT

• EEPROM: IC611

- Temporary operating parameters (for RF, etc.)

• FLASH MEMORY: IC601 (for KX-TG8161 only)

- Voice Prompt (TAM) D/L Area
- ICM/OGM Recording Area

• Additionally,

- Power Supply Circuit (+3.0 V output)
- Crystal Circuit (13.824 MHz)
- Charge Circuit

- Telephone Line Interface Circuit

10

DA801

ANT2

ANT1

TXON

RXON

RXp

RXn

ANT2

ANT1

TXp

TXn

KX-TG8151/8161 BLOCK DIAGRAM (Base Unit_RF Part)

11

(BBIC, Flash Memory, EERROM) is a digital speech/signal processing system that implements all the functions of speechcom-
pression, record and playback, and memory management required in a digital telephone answering machine.The BBIC system
is fully controlled by a host processor. The host processor provides activation and control of all that functionsas follows.

• Voice Message Recording/Play back

The BBIC system uses a proprietary speech compression technique to record and store voice message in Flash Memory.An
error correction algorithm is used to enable playback of these messages from the Flash Memory.

• DTMF Generator

When the DTMF data from the handset is received, the DTMF signal is output.

• Synthesized Voice (Pre-recorded message)

The BBIC implements synthesized Voice, utilizing the built in speech detector and a Flash Memory, which stored the vocabulary.

• Caller ID demodulation

The BBIC implements monitor and demodulate the FSK/DTMF signals that provide CID information from the Central Office.

• Digital Switching

The voice signal from telephone line is transmitted to the handset or the voice signal from the handset is transmitted to theTele-
phone line, etc. They are determined by the signal path route operation of voice signal.

• Block Interface Circuit

RF part, LED, Key scan, Speaker, Telephone line.

Following information data is stored.

• Voice signal

ex: Pre-recorded Greeting message, Incoming message

Following information data is stored.

• Settings

ex: message numbers, ID code, Flash Time, Tone/Pulse

RF part

ADPCM

Analog
Front
End

&
  
Multi-
plexer

TEL
Line
Interface

Digital
Speech
Processor

Caller ID
Modem

Digital TAM  System

Flash Memory  IC601

 Host CPU

DECT RF system
 TDMA/TDD
 Mod/Demod
 PA/LNA

ADPCM

Keys/ LEDs/ Charge

EEPROM IC611

12

• Bell signal detection
• ON/OFF hook and pulse dial circuit
• Side tone circuit

In the idle mode, Q141 is open to cut the DC loop current and decrease the ring load. When ring voltage appears at the Tip (T)
and Ring (R) leads (When the telephone rings), the AC ring voltage is transferred as follows:
R 

 P101  R111  C111  Q111  BBIC pin 5

When the CPU (BBIC) detects a ring signal, Q141 turns on, thus providing an off-hook condition (active DC current flow
throughthe circuit). Following signal flow is the DC current flow.
T 

 D101  Q141  Q161  R163  R167  R168  D101  P101  R

Q141 is open, Q141 is connected as to cut the DC loop current and to cut the voice signal. The unit is consequently in an on-
hook condition.

Pin 6 of BBIC turns Q141 ON/OFF to make the pulse dialing.

Basically this circuit prevents the TX signal from feeding back to RX signal. As for this unit, TX signal feed back from Q161 is
canceled by the canceller circuit of BBIC.

The power supply voltage from AC adaptor is converted to VBAT (3.0V) in DC/DC converter circuit. And +3.0V for peripherals
and analog part is insulated from VBAT by Doubler of BBIC.
Circuit Operation:

5.5V

VBAT

RSTN(Reset) 

pin 54

VBAT

pin 10

pin 57

pin 9

pin 15

IC501

Q301, IC301,
L301, C341

IC601

BBIC

DOUBLER OUT
For peripherals

VDDC (1.2V)

AC Adaptor

3.0V

DC/DC

CONVERTER

CIRCUIT

FLASH

IC611

EEPROM

+3.0V

STM/CKM

Receive

Amp.

RF Part

LCD BLT

ANS LED

MSG LED

Startmonitor

(IC501 57pin)

VDDC (1.2 V)

VBAT

Reset (RSTN) 
(IC501_54 pin)

BBIC chip initialize

(CKM/STM)

LCD

(TAM COUNTER)