Panasonic KX-TG8125RU / KX-TGA810RU / KX-TGA810RUS / KX-TGA810RUT Service Manual ▷ View online
53
KX-TG8125RU/KX-TGA810RU
9.4.3.
How to Install the IC
1. Temporarily fix the FLAT PACKAGE IC, soldering the two marked pins.
*Check the accuracy of the IC setting with the corresponding soldering foil.
2. Apply flux to all pins of the FLAT PACKAGE IC.
3. Solder the pins, sliding the soldering iron in the direction of the arrow.
9.4.4.
How to Remove a Solder Bridge
1. Lightly resolder the bridged portion.
2. Remove the remaining solder along the pins using a soldering iron as shown in the figure below.
2. Remove the remaining solder along the pins using a soldering iron as shown in the figure below.
54
KX-TG8125RU/KX-TGA810RU
9.5.
How to Replace the LLP (Leadless Leadframe Package) IC
9.5.1.
Preparation
• PbF (: Pb free) Solder
• Soldering Iron
• Soldering Iron
Tip Temperature of 700
°F ± 20°F (370°C ± 10°C)
Note:
We recommend a 30 to 40 Watt soldering iron. An expert may be able to use a 60 to 80 Watt iron where someone with less
experience could overheat and damage the PCB foil.
We recommend a 30 to 40 Watt soldering iron. An expert may be able to use a 60 to 80 Watt iron where someone with less
experience could overheat and damage the PCB foil.
• Hot Air Desoldering Tool
Temperature: 608
°F ± 68°F (320°C ± 20°C)
9.5.2.
Caution
• To replace the IC efficiently, choose the right sized nozzle of the hot air desoldering tool that matches the IC package.
• Be careful about the temperature of the hot air desoldering tool not to damage the PCB and/or IC.
• Be careful about the temperature of the hot air desoldering tool not to damage the PCB and/or IC.
9.5.3.
How to Remove the IC
1. Heat the IC with a hot air desoldering tool through the P.C.Board.
2. Pick up the IC with tweezers, etc. when the solder is melted completely.
Note:
• Be careful not to touch the peripheral parts with tweezers, etc. They are unstable.
When it is hard to melt the solder completely, heat it with a hot air desoldering tool through the IC besides through the
P.C.Board.
P.C.Board.
3. After removing the IC, clean the P.C.Board of residual solder.
55
KX-TG8125RU/KX-TGA810RU
9.5.4.
How to Install the IC
1. Place the solder a little on the land where the radiation GND pad on IC bottom is to be attached.
2. Place the solder a little on the land where IC pins are to be attached, then place the IC.
Note:
• When placing the IC, the positioning should be done very carefully.
3. Heat the IC with a hot air desoldering tool through the P.C.Board until the solder on IC bottom is melted.
Note:
• Be sure to place it precisely, controlling the air volume of the hot air desoldering tool.
4. After soldering, confirm there are no short and open circuits with visual inspection.
9.5.5.
How to Remove a Solder Bridge
When a Solder Bridge is found after soldering the bottom of the IC, remove it with a soldering iron.
56
KX-TG8125RU/KX-TGA810RU
10 Disassembly and Assembly Instructions
10.1. Disassembly Instructions
10.1.1. Base Unit
Click on the first or last page to see other KX-TG8125RU / KX-TGA810RU / KX-TGA810RUS / KX-TGA810RUT service manuals if exist.