DOWNLOAD Panasonic KX-TG7851UAB / KX-TG7851UAH / KX-TG7861UAB / KX-TGA785RUB / KX-TGA785RUH Service Manual ↓ Size: 6.65 MB | Pages: 88 in PDF or view online for FREE

21

Make sure the address on LCD is correct when entering new data. Otherwise, you may ruin the unit.

8).   Press

    (off) to return to standby mode.

After that, remove and reinsert the batteries.
Press the Power button for about 1 second if 
the power is not turned on.

?

{OFF}

1).   Press 

{

}

.

2).   Select "Initial Setup" using      or     
       then press  

{

OK

}

.

{^} {V}

3).   Enter "7", "2", "6", "2", "7", "6", "6", "4".

       Note: 7262 7664 = PANA SONI 

                (see letters printed on dial keys)

5).   Enter " ", " ", " ", " " (Address). (*1)

6).   Enter " ", " " (New Data). (*1)

4).   Select "Write EEP" using      or     
       then press 

{

OK

}

 or 

{>}

.

{^} {V}

7).   Press         , a long confirmation beep 

       will be heard.

{

OK

}

_ _ _ _   _ _

Default Data

C

OK

New Data

C

OK

 

22

ex.)

(*1) When you enter the address or New Data, please refer to the table below.

(*2) When adding “01” (hex) to default value, sending level increases by 0.25 dB.
ex.)

(*3) When reducing “01” (hex) from default value, receiving level increases by 0.25 dB.
ex.)

(*4) Use these items in a READ-ONLY mode to confirm the contents. Careless rewriting may cause serious damage to the
handset.

Sending level

04 0E

Adjusted value

Given value

FF

D0

(*2)

Receiving level

04 0F

Adjusted value 

Given value

FF

D0

(*3)

Battery Low

00 09

70

-

-

-

(*4)

Frequency

00 08/00 07

02/70

-

-

-

ID

00 02~00 06

Given value

-

-

-

0

0

A

[R]  +  0

1

1

B

[R]  +  1

.

.

C

[R]  +  2

.

.

D

[R]  +  3

.

.

E

[R]  +  4

9

9

F

[R]  +  5

E7

EB

E3

Sending level

-3.0 dBm

-2.0dBm

-4.0dBm

E4

EB

E3

Receiving level

-27.5 dBm

-26.5 dBm

-28.5 dBm

23

The purpose of this section is to describe the layout of the EEPROM (IC3) for the KX-TGA785 Handset.
The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the
handset, some are set by the user when configuring the handset, and some during normal use of the phone.

The handset uses a 128k bit serial EEPROM (IC3) for storing volatile parameters. All parameters are set up before the handset
the factory. Some of these are vital for the operation of the hardware so a set of default parameters is programmed before the
actual hardware fine-tuning can be initiated. This document lists all default settings with a short description.
This document lists all default parameters with a short description.

F

The data initialized by only F command

0

The data initialized by F and 0 command

1

The data initialized by F, 0 and 1 command

2

The data initialized by F, 0, 1 and 2 command

3

The data initialized by all command (F, 0, 1, 2, 3)

x

Default - no specific country setting, so revert to default value.

03 72

3

EEP_Language

Selected Language for LCD
GERMAN:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3 
FRENCH:4 ITALIAN:5 DENISH:6 DUTCH:7      SWEDISH:8     
FINNISH:9
GREEK:10 TURKISH:11 HUNGARIAN:12 PORTUGUESE:13 
RUSSIAN:14
POLISH:15  SLOVAKIAN:16  CZECH:17  CROATIAN:18  
CATALAN:19
UKRINIAN:20 SPANISHMEX:21   SLOVENIAN:22  
ESTNIAN:23    LITHUANIAN:24
LATVIAN:25  ROMANIAN:26   BULGARIAN:27  
MACEDONIAN:29
ALBANIAN:30  PORTUGUESEMEX:31    ENGLISH(USA):32  
HEBREW:33
ARABIC:34 PERSIA:35    HANTAI:36    HANTAI(HK):37  
RUSSIAN(BX):38
BELARUS:39  KAZAKHSTAN:40    UZBEKISTAN:41   
TAJIKISTAN:42  
TURKMENISTAN:43  AZERBAIJAN:44   ARMENIA:45  
MOLDOV:46
CANADAENGLISH:48  USSPANISH:49  USFRENCH:50  
PORTUGUESE:51  ENGLISH(AZ):52

0x01

0x14

00 12

F

EEP_LcdContrast

0x2A

x

24

Units are reset to the Factory settings by this operation (Erase recorded Voice messages, stored Phone numbers, Caller list and
etc.)

• Some menus are not reset. Refer to Operating Instructions (P.18).
• The reset menus differ depending on the following operations.
• This operation should not be performed for a usual repair.

Both the base unit and the registered handset which you did the following steps 

 to 

 are reset. Other registered handsets

will not be reset.

(*1) Refer to Registering a Handset to a Base Unit in the Operating Instructions.

The only handset is reset by doing the following steps 

 to 

.

Note: (*2)

• The handset registration to the base unit is cancelled.
• If the handset needs to be registered to the base unit, refer to Registering a Handset to a Base Unit in the Operating

Instructions.

• If users do not bring the base unit with them, the registration procedure has to be done by users themselves.

1

 Connect the AC adaptor to the base unit and install the charged batteries into the handset.

2

 Confirm the handset is registered to the base unit (     lights). 

    If the handset is not registered to the base unit (     lights), register it. (*1)

3

 Lift the handset and press 

{ih} to put the handset in standby mode.

4

 Press     ,     ,      and      key of the handset simultaneously until a confirmation tone is heard.

5

 Disconnect the AC adaptor, then remove the battery.

1

5

9

w

1

 Install the charged batteries into the handset.

2

 Lift the handset and press {ih} to put the handset in standby mode.

4

 Remove the battery.

3

 Press     ,     ,      and      key of the handset simultaneously until a confirmation tone is heard. (*2)

3

5

7

#