DOWNLOAD Panasonic KX-TG7851UAB / KX-TG7851UAH / KX-TG7861UAB / KX-TGA785RUB / KX-TGA785RUH Service Manual ↓ Size: 6.65 MB | Pages: 88 in PDF or view online for FREE

17

SIGNAL ROUTE

ROUTE

IN

OUT

SIGNAL

Memo/OGM
Recording
(from Handset)

ICM Recording
(from Tel Line)

(BASE UNIT)
from HANDSET ANT1 - C851 –– DA802  

IC501 (RXn)  –– 

ANT2 - C853 –                        IC501 (RXp) –

IC501 (LSRp) - IC601 (5)

(BASE UNIT)
A –––––––– D101 - Q141 - Q161 - R164 - C173 - R178 - IC501 (MICn) - IC501 (SPI_DO) - IC601 (5)
B - P101–

Message Play
(to Handset)

(BASE UNIT)
IC601 (2) - IC501 (SPI_DI)       IC501 (TXp)        C803 -

(BASE UNIT)
IC601 (2) - IC501 (SPI_DI) - IC501 (LSRp) - C184 - Q161 - Q141 - D101        A

Message Play
(to Tel Line)

Message Play
(to Base Unit)

(BASE UNIT)
IC601 (2) - IC501 (SPI_DI)        IC501 (SPp)

IC501 (SPn)

IC501 (TXn)

DA802

 C851 - ANT1

 C853 - ANT2

 to HANDSET

(HANDSET)
from BASE UNIT   ANT -  C801–– IC1 (1)

– IC2 (2)

IC1 (35) - SP (–)

IC1 (37) - SP (+) 

P101 - B

for KX-TG7861 only

(HANDSET)
MIC (+) - C13 - IC1 (17)        IC1(86)
MIC (–) - C11 - IC1 (18)          IC1(87)          C859  - C801 - ANT to BASE

18

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Items

Contents

Battery

You could use other rechargeable batteries sold in a market, but the unit is not guaranteed to work 
properly.

The battery strength may not be indicated correctly if the battery is disconnected and connected again, 
even after it is fully charged. In that case, by recharging the battery as mentioned in the Operating 
Instructions, you will get a correct indication of the battery strength.

PIN Code

Recall

Earth Recall feature is not supported in this model.

L Change the PIN using the following method.

7

Enter the new 4-digit base unit PIN. 

i

M 

i 

{ic}

#

1 (right soft key)  132

19

Make sure the address on LCD is correct when entering new data. Otherwise, you m ay ruin the unit.

9). Press

   (off) to return to standby mode.

          After that, turn the base unit power off and then power on.

_ _ _ _   _ _

?

{OFF}

1).   Press 

{

}

.

2).   Select "Initial Setup" using      or     
       then press  

{

OK

}

.

{^} {V}

4).   Enter "7", "2", "6", "2", "7", "6", "6", "4".

       Note: 7262 7664 = PANA SONI 

                (see letters printed on dial keys)

6).   Enter " ", " ", " ", " " (Address). (*1)

7).   Enter " ", " " (New Data). (*1)

5).   Select "Write EEP" using      or     
       then press 

{

OK

}

 or 

{>}

.

{^} {V}

3).   Select "Line Setup" using      or     

then press 

{

OK

}

 or 

{>}

.

{^} {V}

 

Default Data

New Data

8).   Press         , a long confirmation beep 

       will be heard.

{

OK

}

20

ex.)

(*1) Refer to Registering a Handset to a Base Unit in the Operating Instructions.
(*2) When you enter the address or New Data, please refer to the table below.

(*3)

C-ID(FSK) sensitivity

06 B9/06 B8

00/51

00/39 

(3 dB up)

00/28 

(6 dB up)

When the hex change from 00/51 to 00/39 or
00/28, gain increase by 3 dB or 6 dB.

C-ID(DTMF) sensitivity

06 BF/06 BE

08/00

0B/4C 

(3 dB up)

0F/F6 

(6 dB up)

When the hex change from 08/00 to 0B/FC or
0F/F6, gain increase by 3 dB or 6 dB.

Frequency

00 08/00 07

02/70

-

-

Use these items in a READ-ONLY mode to
confirm the contents. Careless rewriting may
cause serious damage to the computer system.

ID

00 02~00 06

Given value

-

-

Bell length

03 7D

32 (5 sec) (*3)

1E (3 sec)

14 (2 sec)

This is time until bell stops ringing.
(Unit: 100 msec)

PULSE Dial speed 
(10PPS -> 20PPS)

03 57

28 (40 msec) 

(*3)

11 (17 msec)

-

This is pulse make time. 
(Unit:1 msec)

03 58

3C (60 msec) 

(*3)

21 (33 msec)

-

This is pulse break time. 
(Unit:1 msec)

03 6C

57 (870 msec) 

(*3)

2C (440 msec)

-

This is interdigit time in pulse mode. 
(Unit:1 msec)

0

0

A

[R]  +  0

1

1

B

[R]  +  1

.

.

C

[R]  +  2

.

.

D

[R]  +  3

.

.

E

[R]  +  4

9

9

F

[R]  +  5

Bell length

32 (hex) = 50 (dec) 

 50  100 msec = 5000 msec (5 sec)

PULSE Dial speed 
(10PPS -> 20PPS)

28 (hex) = 40 (dec) 

 40  1 msec = 40 msec  

3C (hex) = 60 (dec) 

60  1 msec = 60 msec

57 (hex) = 87 (dec) 

 87  10 msec = 870 msec