Panasonic KX-TG7175RUS / KX-TGA717RUS Service Manual ▷ View online
57
KX-TG7175RUS/KX-TGA717RUS
11.1.2.2. Batch file Settings
Note:
• “****” varies depending on the country.
11.1.2.3. Commands
See the table below for frequently used commands.
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
98” is written.
setfreq
Adjust Frequency of RFIC
Type “setfreq nn”.
hookoff
Off-hook mode on Base
Type “hookoff”.
hookon
On-hook mode on Base
Type “hookon”.
getchk
Read checksum
Type “getchk”.
wreeprom
Write the data of EEPROM
Type “wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
is data to be written.
58
KX-TG7175RUS/KX-TGA717RUS
11.2. Adjustment Standard (Base Unit)
When connecting the simulator equipments for checking, please refer to below.
11.2.1. Flow Solder Side View
Note:
(A) - (R) is referred to Check Point (Base Unit) (P.45)
PbF
PQUP11410Z
8120
8100
7120
KX-TG7100
A
VDD1
SP
SP+
SP-
ANT
CLK
A_2
A_1
GND
T
X
R
X
VDD4
VDD3
BUZ
DC_IN
DCM
L2T
L1T
L1R
L2R
2
2
4
4
3
1
VDD2
LINE_DC
RED
BLACK
CHARGE
RX
TX
GND
VDD4
VDD3
L1R
L1T
DTMF
Tester
Call - ID
Simulator
BELL
Simulator
LOOP
Simulator
AF
OSC
AF VOLT
METER
OSC
OSC
600
Ω
150
Ω
SP
12
Ω
2 w
CHARGE-
CHARGE+
Digital
Volt Meter
DC_IN
GND
DC POWER
6.5 V
DECT Tester
CMD60
Short A_1 and GND.
GND
ANT
Frequency
Counter
U-ART
PC
GND
CLK
Digital
Volt Meter
GND
LINE_DC
AF
Volt Meter
GND
BUZ
VDD2
Digital
Volt Meter
VDD1
AF VOLT
METER
Dummy
Handset
AF
OSC
MIC
6.3 V 47 uF
(Q
)
(H
)
(Q
)
(A
) (
B
) (
C
)
(D
) (
E
) (
F
) (
G
)
(H
) (
I) (
J
) (
O
)
(I
) (
J
) (
K
) (
L
)
(M
) (
N
) (
O
) (
P
)
(Q
)
(R
)
(F
)
(I
)
59
KX-TG7175RUS/KX-TGA717RUS
11.3. The Setting Method of JIG (Handset)
11.3.1. Preparation
11.3.1.1. Equipment Required
• DECT tester: Rohde & Schwarz, CMD 60 is recommended.
• Frequency counter: It must be precise enough to measure intervals of 1Hz (precision; ±4 ppm).
• Frequency counter: It must be precise enough to measure intervals of 1Hz (precision; ±4 ppm).
Hewlett Packard, 53131A is recommended.
• DC power: it must be able to output at least 1 A current under 2.4 V for Handset.
• Digital multi-meter (DMM): it must be able to measure voltage and current.
• Oscilloscope
• Digital multi-meter (DMM): it must be able to measure voltage and current.
• Oscilloscope
11.3.1.2. JIG and PC
• Serial JIG
JIG Cable: PQZZ1CD300E*
• PC which runs in DOS mode.
• Batch file CD-ROM for setting: PQZZTG7175RU
• Batch file CD-ROM for setting: PQZZTG7175RU
Note:
*: If you have the JIG Cable for TCD500 series
(PQZZ1CD505E), change the following values of resis-
tance. Then you can use it as a JIG Cable for both TCD300
and TCD500 series. (It is an upper compatible JIG Cable.)
(PQZZ1CD505E), change the following values of resis-
tance. Then you can use it as a JIG Cable for both TCD300
and TCD500 series. (It is an upper compatible JIG Cable.)
11.3.2. PC Setting
11.3.2.1. Connections
Connect the DC Power or Battery to J1 (BATT+) and J2 (BATT-) (Handset).
Connect the JIG cable GND (black).
Connect the JIG cable UTX (yellow) and URX (red).
Note:
*: COM port names may vary depending on what your PC calls it.
Resistor
Old value (k
Ω) New value (kΩ)
R2
22
3.3
R3
22
3.3
R4
22
4.7
R7
4.7
10
60
KX-TG7175RUS/KX-TGA717RUS
11.3.2.2. Batch file Settings
Note:
• “*****” varies depending on the country.
11.3.2.3. Commands
See the table below for frequently used commands.
Command name
Function
Example
rdeeprom
Read the data of EEPROM
Type “rdeeprom 00 00 FF”, and the data from address
“00 00” to “FF” is read out.
“00 00” to “FF” is read out.
readid
Read ID (RFPI)
Type “readid”, and the registered ID is read out.
writeid
Write ID (RFPI)
Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E
98” is written.
98” is written.
setfreq
Adjust Frequency of RFIC
Type “setfreq nn”.
getchk
Read checksum
Type “getchk”.
wreeprom
Write the data of EEPROM
Type “wreeprom 01 23 45”. “01 23” is address and “45”
is data to be written.
is data to be written.
Click on the first or last page to see other KX-TG7175RUS / KX-TGA717RUS service manuals if exist.