DOWNLOAD Panasonic KX-TG1411RUM / KX-TG1411RUT / KX-TG1412RU1 / KX-TGA141RUM / KX-TGA141RUT Service Manual ↓ Size: 1.52 MB | Pages: 60 in PDF or view online for FREE

37

This section explains the PC setting to use command required in Check Point (Handset) (P.27).

<Preparation>

• Serial JIG cable: PQZZ1CD300E*
• PC which runs in DOS mode
• Batch file CD-ROM for setting: PNZZTG1411RU

*: If you have the JIG Cable for TCD500 series
(PQZZ1CD505E), change the following values of resis-
tance. Then you can use it as a JIG Cable for both TCD300
and TCD500 series. (It is an upper compatible JIG Cable.)

Connect the DC Power or Battery to BATTERY(+) and BATTERY(-) (Handset).

Serial JIG to the Serial Port of PC.

Connect the Clip cable GND.

Connect the Clip cable UTX and URX.

*: COM port names may vary depending on what your PC calls it.

Resistor

Old value (k

Ω) New value (kΩ)

R2

22

3.3

R3

22

3.3

R4

22

4.7

R7

4.7

10

38

• “*****” varies depending on the country or models.

See the table below for frequently used commands.

Command name

Function

Example

rdeeprom

Read the data of EEPROM

Type “rdeeprom 00 00 FF”, and the data from address “00 00” to “FF” is
read out.

readid

Read ID (RFPI)

Type “readid”, and the registered ID is read out.

writeid

Write ID (RFPI)

Type “writeid 00 18 E0 0E 98”, and the ID “0018 E0 0E 98” is written.

setfreq

adjust Frequency of RFIC

Type “setfreq nn nn”.

Getchk

Read checksum

Type “getchk”.

Wreeprom

write eeprom

Type “wreeprom 01 23 45”. “01 23” is address and “45” is data to be written.

39

When connecting the Simulator Equipments for checking, please refer to below.

(A) - (O) is referred to Check Point (Handset) (P.27)

C155

C112

C140

C146

C148

C102

C107

C142

C100

MIC+

MIC-

C131

RXD

TXD

GND

VBAT

C123

C127

C119

C130

C186

C129

C128

C111

C108

C110

C104

C103

C122

C114

C150

C152

C154

R102

R101

R123

R121

P1.0

BAT

3.3V

R115

R117

R112

L104

L103

1

8

5

4

D104

D106

D105

ANT

ANT1

BZ2

REV

D103

D102

Q104

Q105

Q103

C116

C115

C147

C124

C120

C141

1

C134

C133

C106

C117

C143

C105

C101

C144

C125

C118

C109

C121

C126

C113

C153

C151

C149

C132

R105

R108

R230

R103

R106

R104

R122

R107

R116

R113

R114

X101

D107

Q102

Q101

A

TG131EXR

PQUP11567Z

PbF

BATT Low Check

2.3V

DC Power

2.30V - 2.60V

Serial JIG

PC

4.7k

600

REV+

REV-

ANT

GND

DECT Tester

CMD60

AF VOLT

METER

(O)

(O)

(O)

(H)

(B)

(C)

(I), (J), (K), (L), (M), (N)

(A), (F), (G)

(D), (E)

(O)

LOOP

Simulator

Dummy Base

Unit

AF

OSC

AF

Volt Meter

150

GND

GND

GND

BAT
Battery +

Battery -

P1.0

TP23

TP17

TP22

TP6

TP5

MIC+

MIC-

TXD

RXD

Frequency

Counter

3.3V

Digital

Volt Meter

Power Key

TALK Key

DC

6V

AF

Generator

6.3 V 47   F 

40

If repairing or replacing BBIC (FLASH type), EEPROM , it is necessary  to download the required data such as Programming
data or adjustment data, etc in memory.
The set doesn't operate if it is not executed.

First, operate the PC setting according to The Setting Method of JIG (Base Unit) (P.33).
Then download the appropriate data according to the following procedures.

(*1) Refer to Check Point (Base Unit) (P.24)
(*2) XX: country code, YY: revision number
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (Base Unit) (P.33).

First, operate the PC setting according to The Setting Method of JIG (Handset) (P.37).
Then download the appropriate data according to the following procedures.

(*3) Refer to Check Point (Handset) (P.27)
(*4) XX: country code, YY: revision number
“XX” and “YY” vary depending on the country version. You can find them in the batch file, PNZZ- mentioned in The Setting
Method of JIG (Handset) (P.37).

IC

How to download/Required adjustment

BBIC

Programming data is stored in memory.

1) Clock adjustment: Refer to Check Point (E). (*1)

EEPROM Adjusted parameter data is stored in memory.

(country version batch file, default batch file, etc.)

1) Default batch file: Execute the command “Default4KB”.
2) Country version batch file: Execute the command 
“1311XXvYY.bat”. (*2)     
3) Clock adjustment: Refer to Check Point (E). (*1)

IC

How to download/Required adjustment

BBIC

Programming data is stored in memory.

1) Clock adjustment: Refer to Check Point (H). (*3)
2) 4.0 V setting and battery low detection: Refer to Check Point (A),
(F) and (G). (*3)

EEPROM Adjusted parameter data is stored in memory.

(country version batch file, default batch file, etc.)

1) Default batch file: Execute the command “Default”.
2) Melody Initialize batch file; Execute the Command “DB3MZA”.
3) Country version batch file: Execute the command 
“131XXvYY.bat”. (*4)
4) Clock adjustment: Refer to Check Point (H). (*3)
5) 4.0 V setting and battery low detection: Refer to Check Point (A),
(F) and (G). (*3)