DOWNLOAD Panasonic KX-TCD961EB Service Manual ↓ Size: 1.66 MB | Pages: 64 in PDF or view online for FREE

5

Fig. 5

Fig. 3

Fig. 4

Fig. 6

Fig. 9

Fig. 7

Fig. 8

(C)

(D)

(E)

Ref No.

Procedure

Shown in Fig.

To Remove

 Remove

1

1, 2

3

3, 4

3~6

3~7

3~8

Lower Cabinet

P.C. Board

Battery Cover

Rear Cabinet

Screws (2.6

~

14) ........................... (A)

~

4

Remove the P.C. Board

Remove the Battery Cover

Screws (2.6

~

10) ........................... (B)

~

2

Screws (2.6

~

10) ........................... (C)

~

2

Pull the Connector Locks ............... (D)

~

2

Pull the LCD Lead ......................... (E)

~

1

1
2

3

4

5

6

7

3

4

9

6

P.C. Board

LCD Lead

8

5

When removing the rear cabinet of handset, attach the belt clip and press it as shown in Fig. 7.

6

Install the batteries as shown. Then install the handset cover.

•

 If the rechargeable batteries are not inserted correctly, the handset will not work.

Fig. 10

Plug in the AC adaptor and the telephone line cord to the bottom of the unit. Then connect the
cords as shown.

•

USE ONLY WITH Panasonic AC ADAPTOR KX-TCA11E.

•

Be careful not to confuse the telephone line jack with the AC adaptor jack on the base unit. If
connected improperly, the base unit will not work and damage may occur.

•

The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

This apparatus is intended for use when powered by the KX-TCA11E.
Using other power supplies will invalidate any approval given to this apparatus.

Telephone 
Line Cord

AC
Adaptor

Fasten the cords to prevent them from 
being disconnected.

Hooks

T

elephone Line Cord

AC Adaptor

To Mains Outlet 
(AC 230 - 240 V, 50 Hz)

To B.T. Socket

TNV*

*The abbreviation TNV means 

"Telephone Network Voltage".

Fig. 11

7

At the time of shipment, the batteries
are not charged. To charge, place
the handset on the base unit. Please
charge the batteries for about
4 hours before initial use.

•

The charge indicator (        ) lights.

When "         " flashes or the unit beeps every
15 seconds, recharge the batteries.

After your Panasonic batteries are fully charged:

(Flashing)

You can check the present battery strength on the display.

•

Battery life may vary depending on usage conditions and ambient temperature.

•

Clean the handset and the base unit charge contacts with a soft, dry cloth.
Clean if the unit is subject to grease, dust or high humidity. Otherwise the batteries
may not charge properly.

•

If the batteries are fully charged, you do not have to place the handset on the base unit until
"         " flashes. This will maximize the battery life.

•

The batteries cannot be overcharged.

•

Nickel metal hydride (Ni-MH) rechargeable batteries (AAA size) are available.
* When you use the Ni-MH batteries, the battery strength will not be displayed correctly.

Charge Indicator (         )

OR

While in use (Talk)

While not in use (Stand-By)

Up to about 6 hours

Up to about 65 hours

Up to about 12 hours

Up to about 130 hours

8

You can hang the handset on your belt or pocket using the belt clip.

You can program the dialling mode to tone or pulse. If you have touch tone service, set to tone. If rotary or pulse service is
used, set to pulse. The factory preset is tone.
Make sure that the power is ON and the unit is in the stand-by mode.

Fig. 14

Fig. 15

•

The factory preset is 0000.

Ex. Tone is selected.

•

A confirmation tone sounds and the display
will return to the stand-by mode.

•

The current mode is displayed.
1:Tone

2:Pulse

•

If 5 beeps sound in step 3, the entered password is
incorrect. Enter the correct password.

•

To cancel during programming, press          ,
then start from step 1.