Panasonic KX-TCD951EB / KX-TCD955EC Service Manual ▷ View online
5
KX-TCD951EB/KX-TCD955EC
When removing the rear cabinet, attach the belt clip and press the belt clip as direction arrow. ( Fig. 8)
DISASSEMBLY INSTRUCTION
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Ref No.
Procedure
Shown in Fig.
To Remove
Remove
1
1, 2
3
3, 4
3~6
3~7
3~8
Lower Cabinet
P.C. Board
Battery Cover
Rear Cabinet
Screws (3•~14) .............................. (A)•~4
Remove the P.C. Board
Remove the Battery Cover
Screws (2.6•~10) ........................... (B)•~2
Screws (2.6•~10) ........................... (C)•~2
Pull the Connector Locks ............... (D)•~2
Pull the LCD Lead .......................... (E)•~1
1
2
3
4
5
6
7
3
4
9
6
P.C. Board
LCD Lead
8
5
(C)
(D)
(E)
KX-TCD951EB/KX-TCD955EC
6
SETTINGS
INSTALLING THE BATTERIES IN THE HANDSET
Install the batteries as shown. Then install the handset cover.
•
If the rechargeable batteries are not inserted correctly, the handset will not work.
C O N N E C T I O N S
Plug in the AC adaptor and the telephone line cord to the bottom of the unit. Then connect the cords as shown.
• USE ONLY WITH Panasonic AC ADAPTOR KX-TCA9E or KX-TCA11E.
• Be careful not to confuse the telephone line jack with the AC adaptor jack on the base unit. If connected improperly, the base
unit will not work and damage may occur.
• The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)
• If your unit is connected to a PBX which does not support Caller ID services, you cannot access those services.
Fig. 10
Fig. 11
8V
9V
Fasten the cords to prevent them
from being disconnected.
from being disconnected.
Hooks
To Mains Outlet
(AC 230–240 V, 50 Hz)
(AC 230–240 V, 50 Hz)
To B.T. Socket
AC Adaptor
Telephone Line Cord
TNV*
Telephone
Line Cord
Line Cord
AC
Adaptor
Adaptor
*The abbreviation TNV means
“Telephone Network Voltage”.
7
KX-TCD951EB/KX-TCD955EC
BATTERY CHARGE
At the time of shipment, the batteries are not charged. To charge, place
the handset on the base unit. Please charge the batteries for about
4 hours before initial use.
•
The charge indicator (
) lights.
Battery strength
You can check the present battery strength on the display.
Recharge
When "
" flashes or the unit beeps every 15 seconds, recharge the batteries.
Battery information
If your Panasonic battery is fully charged:
Operation
Approx. Ni-Cd battery life (Included)
While in use (Talk)
Up to about 6 hours
While not in use (Stand-By)
Up to about 65 hours
• Battery life may vary depending on usage conditions and ambient temperature.
• Clean the handset and the base unit charge contacts with a soft, dry cloth. If the unit
is subject to grease, dust or high humidity. Otherwise the batteries may not charge properly.
• If the batteries are fully charged, you do not have to place the handset on the base unit until "
" flashes. This will
maximize the battery life.
• The batteries cannot be overcharged.
• Nickel metal hydride (Ni-MH) rechargeable batteries (AAA size) are available.
• Read "Important Notice Concerning the Correct Use and Charging of Ni-Cd (Ni-MH) Batteries".
Fig. 12
Approx. Ni-MH battery life (Optional)
Up to about 12 hours
Up to about 130 hours
OR
Charge Indicator ( )
Battery strength
Battery icon
(Flashing)
Fully charged
No power
Low
Medium
Fig.13
(KX-TCD951EB)
(KX-TCD955EC)
3 New Calls
Base 1
KX-TCD951EB/KX-TCD955EC
8
INSTALLING THE HANDSET CLIP
You can hang the handset on your belt or pocket using the belt clip.
To remove the belt clip
SELECTING THE DIALING MODE
You can program the dialling mode to tone or pulse. If you have touch tone service, set to tone. If rotary or pulse service is
used, set to pulse. The factory preset is tone.
Make sure that the power is ON and the unit is in the stand-by mode.
(KX-TCD951EB)
Fig. 14
Fig. 15
1
Press
PROG
then
I N T
.
2
Press
3
.
3
Enter the base unit password.
• The factory preset is 0000. To change the base unit
password.
4
Press
1
.
• The current mode is displayed.
1:Tone 2:Pulse
Ex. Tone is selected.
5
To select Pulse, press
2
.
O R
To select Tone, press
1
.
6
Press
.
• A confirmation tone sounds and the display will return to
the stand-by mode.
• If 5 beeps sound in step 3, the entered password is
incorrect. Enter the correct password.
• To cancel during programming, press
PROG
,
then start from step 1.
Click on the first or last page to see other KX-TCD951EB / KX-TCD955EC service manuals if exist.