Panasonic KX-TCD400RUB / KX-TCD400RUC / KX-TCD400RUF / KX-A140RUB / KX-A140RUC / KX-A140RUF Service Manual ▷ View online
6.3.3. Reset Base Unit PIN to Default (0000) -When There is NO Handset Registered-
6.3.3.1. Symptom
6.3.3.1. Symptom
There is no way to reset base PIN when there is no handset registered to the base.
6.3.3.2. Thinkable Situation
·
Customer may ask to reset base PIN because they forget it.
·
Customer may bring only a base unit for repair and there is no handset registered to the base (Need to register another handset
to the base to confirm if the unit works properly after repair).
to the base to confirm if the unit works properly after repair).
·
When original handset has broken and customer purchased a new one, if customer forget base PIN, customer cannot register
the new handset and may ask to reset the PIN.
the new handset and may ask to reset the PIN.
6.3.3.3. Remedy
<Preparation>
Refer to JIGs and PC (P.35).
<Connection>
1. Solder a pin or lead wire to GND, SDA, and SCLK on base PCB.
2. Plug in AC adaptor to the base.
3. Turn on the power to the JIG (9V).
4. Then connect the cable to each pins using clip.
As for the connection between JIG and PCB, see below photos.
2. Plug in AC adaptor to the base.
3. Turn on the power to the JIG (9V).
4. Then connect the cable to each pins using clip.
As for the connection between JIG and PCB, see below photos.
Clip
Base PCB
GND
SD
A
SCL
+2.7V
MODE
SDA
SCLK
GND
J104
J103
J102
J101
J100
<PC setting and how to reset base PIN to default (0000)>
1. Refer to PC Setting (P.35).
2. Next, execute <initbspin.bat> by typing "initbspin". The PC display will be shown as below.
2. Next, execute <initbspin.bat> by typing "initbspin". The PC display will be shown as below.
Microsoft Windows 2000 [Version 5.00.2195]
(C) Copyright 1985-2000 Microsoft Corp.
C:
>cd dect
C:
DECT>DOSKEY
C:
DECT>SET RTX_COM=1
C:
DECT>initbspin
C:
DECT>call wreeprom.bat 00 25 00
C:
DECT>call wreeprom.bat 00 26 00
C:
DECT>_
3. After that, turn off DC power supply (9V)to the jig, unplug AC adaptor, and remove pins on PCB.
Then close the cabinet. The base pin returns to the default (0000)and you can register a handset to the base using the base
PIN (0000).
PIN (0000).
13
KX-TCD400RUB / KX-TCD400RUC / KX-TCD400RUF / KX-A140RUB / KX-A140RUC / KX-A140RUF
6.4. Reset
6.4.2. Handset
·
To exit the operation, press
any time.
·
*1: The factory preset is 0000.
6.4.1. Base Unit
·
To exit the operation, press
any time.
·
*1: The factory preset is 0000.
Base Unit Initial Settings
Function
Initial Setting
Remarks (selectable options)
Flash Timing
700 msec
All Handsets/Specific Handset No.
Pause Timing
3 seconds
3 seconds/5 seconds
4-Digit Base Unit PIN
0000
-
Dialling Mode
Pulse
Tone/Pulse
ARS Setting
OFF
ON/OFF
Carrier Code
All Clear
-
Area Code
All Clear
-
Relation of Area Code
All Area Code to Carrier Code 1
1 to 5
You can reset all of the handset settings to their initial settings.
14
KX-TCD400RUB / KX-TCD400RUC / KX-TCD400RUF / KX-A140RUB / KX-A140RUC / KX-A140RUF
Handset Initial Settings
Function
Initial Setting
Remarks (selectable options)
Time Alarm Mode
OFF
OFF/ON
Alarm Time
Clear
OFF/Once/Daily
Handset Ringer Volume
6
-
Handset External Ringer Pattern
1
20 patterns
Handset Alarm Tone Pattern
1
20 patterns
Key Tone
ON
ON/OFF
Range Warning Alarm
OFF
OFF/ON
Battery LowAlarm
ON
ON/OFF
Talk Mode Display
Length of the Call
Talk Time/Phone No.
Display Language
English
10 languages
Call BAR
OFF
OFF/ON
Direct Call Mode
OFF
OFF/ON
Direct Call Number
Clear
Up to 24 digits
4-Digit Handset PIN
0000
-
Auto Talk
OFF
OFF/ON
Redial Memory
All Clear
-
Handset Receiver Volume
Medium
Low/Medium/High
6.5. Key Lock
You can lock the handset dialling buttons. Only incoming calls are accepted while the key lock is on. The key lock is cancelled
if the handset is turned off.
When the key lock is on, emergency calls cannot be made until key lock is cancelled.
if the handset is turned off.
When the key lock is on, emergency calls cannot be made until key lock is cancelled.
·
is displayed (Refer to Handset Display (P.19)) and all dialling buttons are locked.
6.6. Recall Feature
RECALL is used to access special telephone services. Contact your Network provider for details. If your unit is connected to
a PBX, pressing RECALL allows you to access some features of your host PBX such as transferring an extension call.
a PBX, pressing RECALL allows you to access some features of your host PBX such as transferring an extension call.
6.7. Dialling Pause for PBX line/long distance service users
A dialling pause is used when a pause in the dialling of the phone number is necessary using a PBX or accessing a long
distance service.
For example, when 9 (line access number)is dialled followed by a pause to access an outside line through a PBX:
distance service.
For example, when 9 (line access number)is dialled followed by a pause to access an outside line through a PBX:
·
Entering a pause prevents misdialling when you redial or dial a stored number.
·
Pressing REDIAL once creates one pause. To extend the pause requirement time, press REDIAL accordingly.
*1
is displayed (Refer to Handset Display (P.19)) on the LCD.
15
KX-TCD400RUB / KX-TCD400RUC / KX-TCD400RUF / KX-A140RUB / KX-A140RUC / KX-A140RUF
6.8. Call BAR On/Off (Call Prohibition On/Off)
You cannot make any dialling if call BAR is on.
·
To exit the operation, press
any time.
·
*1: The factory preset is 0000.
·
*2: If
is selected,
is displayed (Refer to Handset Display (P.19)).
6.9. Selecting the Display Language
·
To exit the operation, press
any time.
·
*1 You can select one of 10 languages. If you set a language you cannot read, reset the handset to its initial settings.
Press MENU
Press MENU
→
DOWN
→
RIGHT
→
UP
→
RIGHT
→
4-digit Handset PIN
→
UP
→
OK
All handset setting will be reset to their initial settings, however, the Phonebook data will be saved.
6.10. Select Dialling Mode (Tone/Pulse)
You can change the dialling mode to tone or pulse depending upon your network service. If you have a touch tone service,
select tone. If you have rotary or pulse service, select pulse.
select tone. If you have rotary or pulse service, select pulse.
·
To exit the operation, press
any time.
·
*1: The factory preset is 0000.
16
KX-TCD400RUB / KX-TCD400RUC / KX-TCD400RUF / KX-A140RUB / KX-A140RUC / KX-A140RUF
Click on the first or last page to see other KX-TCD400RUB / KX-TCD400RUC / KX-TCD400RUF / KX-A140RUB / KX-A140RUC / KX-A140RUF service manuals if exist.