DOWNLOAD Panasonic KX-PRS110RUW / KX-PRS120RUW / KX-PRSA10RUW Service Manual ↓ Size: 5.58 MB | Pages: 83 in PDF or view online for FREE

17

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

Refer to the Operating Instructions.

You can download and refer to the Operating Instructions (Instruction book) on TSN Server.

[Menu] (right soft key)     

132

Items

Contents

Battery

You could use other rechargeable batteries sold in a market, but the unit is not guaranteed to work 
properly.

The battery strength may not be indicated correctly if the battery is disconnected and connected again, 
even after it is fully charged. In that case, by recharging the battery as mentioned in the Operating 
Instructions, you will get a correct indication of the battery strength.

PIN Code

Recall

Earth Recall feature is not supported in this model.

L Change the PIN using the following method.

7

Enter the new 4-digit base unit PIN. 

i [OK]

#

[  ]: “Yes” 

i [OK] i [}c]

18

1).   Press 

{Menu}

.

2).   Select "Initial Setup" using   
       then press  

{

OK

}

.

4).   Enter "7", "2", "6", "2", "7", "6", "6", "4".

       Note: 7262 7664 = PANA SONI 

                (see letters printed on dial keys)

6).   Enter " ", " ", " ", " " (Address). (*1)

7).   Enter " ", " " (New Data). (*1)

5).   Select "Write EEP" using      or     
       then press 

{

OK

}

{^}

3).   Select "Line Setup" using       or 

then press 

{

OK

}

.

{^}

Ringer Setup

Time Settings

Talking Caller ID

Handset Name

Caller Barred

Default Data

New Data

8).   Press         , a long confirmation beep 

       will be heard.

{

OK

}

?

{OFF}

{^}, {V}, {<}, {>},

{V}

.

Auto Talk

Line Setup

Privacy Mode

Memory Manager

Base Unit PIN

Read EEP

Write EEP

Get S/W Ver.

{V}

Make sure the address on LCD is correct when entering new data. Otherwise, you m ay ruin the unit.

9). Press

   (off) to return to standby mode.

          After that, turn the base unit power off and then power on.

____   __

19

ex.)

(*1) Refer to Registering a Handset to a Base Unit in the Operating Instructions.
(*2) When you enter the address or New Data, please refer to the table below.

(*3)

C-ID(FSK) sensitivity

06 B9/06 B8

00/51

00/39 

(3 dB up)

00/28 

(6 dB up)

When the hex change from 00/51 to 00/39 or
00/28, gain increase by 3 dB or 6 dB.

C-ID(DTMF) sensitivity

06 BF/06 BE

08/00

0B/4C 

(3 dB up)

0F/F6 

(6 dB up)

When the hex change from 08/00 to 0B/FC or
0F/F6, gain increase by 3 dB or 6 dB.

SMS (FSK) receiving  
sensitivity

06 B9/06 B8

00/51

00/39 

(3 dB up)

00/28 

(6 dB up)

When the hex change from 00/51 to 00/39 or
00/28, gain increase by 3 dB or 6 dB.

SMS (FSK) sending level

07 49/07 4A

00/40

00/38 

(3 dB up)

00/4F 

(6 dB up)

When hex changes from “00/4A” to “00/38” or
“00/4F”, gain increases by 3 dB or 6 dB.

Frequency

00 08/00 07

02/70

-

-

Use these items in a READ-ONLY mode to
confirm the contents. Careless rewriting may
cause serious damage to the computer system.

ID

00 02~00 06

Given value

-

-

Bell length

03 7F

32 (5 sec) (*3)

1E (3 sec)

14 (2 sec)

This is time until bell stops ringing.
(Unit: 100 msec)

PULSE Dial speed 
(10PPS -> 20PPS)

03 59

28 (40 msec) 

(*3)

11 (17 msec)

-

This is pulse make time. 
(Unit:1 msec)

03 60

3C (60 msec) 

(*3)

21 (33 msec)

-

This is pulse break time. 
(Unit:1 msec)

03 6E

57 (870 msec) 

(*3)

2C (440 msec)

-

This is interdigit time in pulse mode. 
(Unit:1 msec)

0

0

A

[R]  +  0

1

1

B

[R]  +  1

.

.

C

[R]  +  2

.

.

D

[R]  +  3

.

.

E

[R]  +  4

9

9

F

[R]  +  5

Bell length

32 (hex) = 50 (dec) 

 50  100 msec = 5000 msec (5 sec)

PULSE Dial speed 
(10PPS -> 20PPS)

28 (hex) = 40 (dec) 

 40   1 msec = 40 msec  

3C (hex) = 60 (dec) 

 60  1 msec = 60 msec

57 (hex) = 87 (dec) 

 87  10 msec = 870 msec

20

Make sure the address on LCD is correct when entering new data. Otherwise, you may ruin the unit.

8).   Press

    (off) to return to standby mode.

After that, remove and reinsert the batteries.
Press the Power button for about 1 second if 
the power is not turned on.

1).   Press 

3).   Enter "7", "2", "6", "2", "7", "6", "6", "4".

       Note: 7262 7664 = PANA SONI 

                (see letters printed on dial keys)

5).   Enter " ", " ", " ", " " (Address). (*1)

6).   Enter " ", " " (New Data). (*1)

7).   Press         , a long confirmation beep 

       will be heard.

{

OK

}

{Menu}

.

2).   Select "Initial Setup" using   
       then press  

{

OK

}

.

{^}, {V}, {<}, {>},

4).   Select "Write EEP" using      or     
       then press 

{

OK

}

{^}

{V}

.

Default Data

New Data

Read EEP

Write EEP

Get S/W Ver.

____   __

?

{OFF}