Panasonic PT-RZ970 / PT-RW930 / PT-RX110 (serv.man6) Service Manual ▷ View online
SECTION
3
ADJ-1
CONTENTS
1. Adjustment item and a procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . ADJ-2
1. 1. Lighting area adjustment
1. 2. Lens calibration
1. 3. Wheel index adjustment
1. 4. EEPROM data transfer
1. 5. Model information setup
1. 6. Date and time setup
1. 7. LD unit runtime reset
1. 8. LD unit status reset
1. 2. Lens calibration
1. 3. Wheel index adjustment
1. 4. EEPROM data transfer
1. 5. Model information setup
1. 6. Date and time setup
1. 7. LD unit runtime reset
1. 8. LD unit status reset
2. Firmware Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ADJ-14
2. 1. Equipment to be used
2. 2. Connection Preparations
2. 3. Update procedure
2. 2. Connection Preparations
2. 3. Update procedure
Illustrations of the projector and other parts may vary from the actual product.
SECTION 3 ADJUSTMENTS
ADJ-2
SECTION 3 ADJUSTMENTS
< RZ970/RW930/RX110 >
1. Adjustment item and a procedure
f
When the following parts are disassembled or replaced, please adjust the items according to the table below.
Adjustment Item
Replaced Component
Remarks
1.1. Lighting area adjustment
Parts in the DMD block, Lighting block
1.2. Lens calibration
DMD block, Lens mounter, Stepping motor
[A]-P.C.Board
It is necessary if turn off during operating the lens
shift or moved the lens shift by manually.
1.3. Wheel index adjustment
Phosphor wheel / Color wheel
1.4. EEPROM data transfer
[A]-P.C.Board
Transfer the data from old [A]-P.C.Board to new
one
1.5. Model information setup
[A]-P.C.Board
1.6. Date and time setup
[A]-P.C.Board / Lithium battery
1.7. LD unit runtime reset
LD unit
1.8. LD unit status reset
---
It clears the error status of the LD unit.
1. 1. Lighting area adjustment
1. 1. 1. Lighting area confirmation
1. Check if any shade is visible in the DMD effective display
area.
• Make the projection environment as dark as possible,
and project an all-white and all-black pattern of internal
pattern.
2. When the Lighting area interferes with the effective area,
adjust the relay lens holder position
Lighting area
Effective area
Sheet cover
1. 1. 2. Lighting area adjustment
1. Pull the adjustment cover sheet up.
ADJ-3
SECTION 3 ADJUSTMENTS
< RZ970/RW930/RX110 >
2. Loosen 2 fix screws with a hexagon wrench (2.5 mm).
3. Project the all-black of the internal test pattern. (PICTURE MODE : DYNAMIC, DYNAMIC CONTRAST : 3 )
4. Adjust so that the lighting area (effective area outside) is right to left or up and down evenly.
1) Adjust the horizontal direction of the lighting area with an adjustment screw [A].
2) Adjust the vertical direction of the lighting area with an adjustment screw [B]
5. Project an all-white pattern of internal pattern and check the lighting area interferes with the effective area.
6. After completing the adjustment, tighten two fixation screws.
7. Fix up the adjustment cover sheet.
Lighting area
Effective area
Adjustment screw [A]
Adjustment screw [B]
Adjustment screw [B]
Fixation screws
Torque : 70±10 Ntcm
Adjustment screw [A]
1. 2. Lens calibration
1. Select sub menu [LENS CALIBRATION] of [PROJECTOR SETUP] menu.
2. Select the used lens type and press the <ENTER> button.
t NORMAL : When using the other than ET-DLE030
t DLE030 : When using the ET-DLE030 (Fixed-focus Lens)
ADJ-4
SECTION 3 ADJUSTMENTS
< RZ970/RW930/RX110 >
3. A confirmation message is displayed and select [OK].
4. A confirmation message is displayed and select [OK].
5. After finishing the calibration, the main menu will be displayed.
1. 3. Wheel index adjustment
1. Enter the service mode, and select submenu [AUTO INDEX CALIBRATION] of [EXTRA OPTION].
2. Select [OK] from confirmation message and press the <ENTER> button.
3. Wheel index adjustment pattern is projected automatically, automatic adjustment is started.
4. When the adjustment is complete "AUTO INDEX CALIBRATION COMPLETE" message is displayed.
Press the <MENU> button to finish the adjustment.
Click on the first or last page to see other PT-RZ970 / PT-RW930 / PT-RX110 (serv.man6) service manuals if exist.