DOWNLOAD Panasonic PT-RZ670 / PT-RW630 (serv.man16) Service Manual ↓ Size: 62.77 MB | Pages: 115 in PDF or view online for FREE

SECTION 1  SERVICE  INFORMATION

< RZ670/RW630 >

- RADIATOR1

RADIATOR1 fan condition [Rotational speed]

- RADIATOR2

RADIATOR2 fan condition [Rotational speed]

- RADIATOR3

RADIATOR3 fan condition [Rotational speed]

- DMD

DMD fan condition [Rotational speed]

- PHOSPHOR1

Phosphor wheel1 fan condition [Rotational speed]

- PHOSPHOR2

Phosphor wheel2 fan condition [Rotational speed]

- P_INTAKE

Power fan condition [Rotational speed]

- DRIVER

LD driver fan condition [Rotational speed]

- EXHAUST1

Exhaust1 fan condition [Rotational speed]

- EXHAUST2

Exhaust2 fan condition [Rotational speed]

- EXHAUST3

Exhaust3 fan condition [Rotational speed]

- PUMP1

Liquid cooling pump1 condition [Rotational speed]

- PUMP2

Liquid cooling pump2 condition [Rotational speed]

 5) Page 7 (Add Page)

Value of color sensor (Factory use only)

- R.SEG

Red segment value

Y / x / y

- G.SEG

Green segment value

Y / x / y

- B.SEG

Blue segment value

Y / x / y

- Y.SEG

Yellow segment value

Y / x / y

6) Page 8 (Add Page)

- ON COUNT

Number of times that each LD unit turned ON

- RUNTIME

Lighting time of each LD unit

- LD1 STATUS

State of LD1 (0: Off / 1: ON)

- LD2 STATUS

State of LD2 (0: OFF / 1: ON)

7) Page 9 (Add Page)

Information of SDI signal. (No signal is "---" displayed)

- MODE

Mode (「NO SIGNAL」,「SD-SDI」,「HD-SDI」,「3G-SDI」)

- TRANSPORT

Conversion method (「PROGRESSIVE」,「INTERLACED」)

- PICTURE

Picture information (「PROGRESSIVE」,「INTERLACED」)

- RATE

Rate information (「23.98」,「24」,「25」,「29.97」,「30」,「50」,「59.94」,「60」)

- SAMPLING

Sampling information

(「4:2:2 (YPBPR)」、「4:2:2 (YCBCR)」、「4:4:4 (YPBPR)」、「4:4:4 (YCBCR)」、
「4:4:4 (RGB)」、「4:4:4:4 (YPBPR+A)」、「4:4:4:4 (RGB+A)」、「4:4:4 (XYZ)」)

- BIT DEPTH

Bit depth (「8bit」,「10bit」,「12bit」)

8) Page 10 (Add Page)

- LD1 HISTORY

ON/OFF history log of LD1

9) Page 11 (Add Page)

- LD2 HISTORY

ON/OFF history log of LD2

INF - 12

SECTION 1  SERVICE  INFORMATION

< RZ670/RW630 >

4. [TEST PATTERN] menu

・ The following test patterns are added.

- Checker pattern

- Checker inverted pattern

- Red pattern

- Magenta pattern 

- Green pattern

- Yellow pattern

- Blue pattern

- Cyan pattern

- Convergence pattern

- Wheel index adjustment pattern

5. [NETWORK] menu

・ [CHANNEL A - D] information is added to [SIGNAL QUALITY] of sub menu [DIGITAL LINK STATUS].

6. [LENS SHIFT] adjustment screen

・ [VERTICAL POSITION] & [HORIZONTAL POSITION] are added.

INF - 13

SECTION 1  SERVICE  INFORMATION

< RZ670/RW630 >

The [SERIAL IN] terminal of the projector conforms with RS ‑232C so that the projector can be connected to and controlled
from a computer. Also [SERIAL OUT] terminal is provided to enable plural projector control.

Projector connecting terminals

Computer

D-Sub 9p (female)

D-Sub 9p (male)

D-Sub 9p (male)

Communication cable (straight)

Connecting terminals on projector 2

D-Sub 9p (female)

D-Sub 9p (male)

D-Sub 9p (female)

D-Sub 9p (male)

Connecting terminals on projector 1

Computer

D-Sub 9p (male)

D-Sub 9p (female)

D-Sub 9p (male)

Communication cable

Communication cable

DIGITAL LINK compatible device

Computer

D-Sub 9p (female)

Projector connecting terminals

DIGITAL LINK

DIGITAL LINK

D-Sub 9p (male)

Communication cable (straight)

LAN cable (straight)

 

f The destination of [RS-232C]   

 

must be set according to the connection method.

 

f When connecting by a DIGITAL LINK compatible device, set the [PROJECTOR SETUP] menu → [STANDBY MODE]

 

 

setting 

to [NORMAL] to control the projector during standby.
When [STANDBY MODE] is set to [ECO], the projector cannot be control during standby.

―

NC

TXD

Transmitted data

RXD

Received data

―

NC

GND

Earth

―

NC

CTS

Connected
internally

RTS

―

NC

―

NC

RXD

Received data

TXD

Transmitted data

―

NC

GND

Earth

―

NC

RTS

Connected
internally

CTS

―

NC

INF - 14

SECTION 1  SERVICE  INFORMATION

< RZ670/RW630 >

1. Select [RS-232C] in sub menu [PROJECTOR SETUP].

2. Select communication condition by pressing   ▲ ▼ button.

    Set it with pressing  　　　　button.

3. Press MENU button 3 times and return to regular display.

 

Transmission from the computer starts with STX, then the ID, command, parameter, and ETX are sent in this order.

Add parameters according to the details of control.

1. Basic control command (without parameter)

2. Basic control command (with parameters)

3. Basic control command (with sub command)

Start

(STX)

ＩＤ

End

(ETX)

End

(ETX)

Separator

(colon)

Separator

(colon)

Parameter

Parameter

Operation

5 byte

1 byte

1 byte

4 byte

1 byte

ＩＤ

Command

4 byte

1 byte

3 byte

Start

(STX)

ＩＤ

Separator

(semicolon)

Command

Separator

(semicolon)

Command

Separator

(semicolon)

Start

(STX)

3 byte

1 byte

End

(ETX)

1 byte

4 byte

Undefined length

3 byte

1 byte

1 byte

1 byte

5 byte

1 byte

Parameter

Sign

1 byte

1 byte

1 byte

RS-232C-compliant

Asynchronous

9 600 bps

None

8 bits

1 bit

None

None

▲

▼

C

N

 

 

 

C

N

C

N

 

 

 

C

N

C

N

 

 

 

C

N

C

N

 

 

 

C

N

C

N

 

 

 

C

N

C

N

 

 

 

C

N

C

N

 

 

 

C

N

C

N

 

 

 

C

N

Projector

(<SERIAL IN> terminal)

Computer

(DTE specifications)

Projector 1

(<SERIAL OUT> 

terminal)

Projector 2

(<SERIAL IN> 
terminal)

INF - 15