DOWNLOAD Panasonic PT-RZ475U / PT-RZ475E / PT-RZ475EA Service Manual ↓ Size: 25.32 MB | Pages: 75 in PDF or view online for FREE

 Accuracy : 

≦

 2%

 Input resistance :

≧

 1 MΩ

 Input capactance :

≦

 200 pF

 Frequency range :

15 Hz to 1 MHz

1. Prepare the measuring circuit as shown in Fig.1.
    Be sure to use a voltmeter having the performance described in Table 1.
2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a power outlet.
3. Connect M1 to T1 according to Fig. 2 and measure the voltage.
4. Change the connection of M1 from T1 to T2 and measure the voltage again.
5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4.  This means that the current must be 0.75mA
    or less.
6. If the reading is out of the above standard, the projector must be repaired and rechecked before returning to the
    customer because of a possibility of an electric shock.

- For continued safety, no modification of any circuit must be attempted.
- Unplug the power cord from the power outlet before disassembling this projector.
- Use correctly the supplied power cord and must ground it.
- It is advisable to use an isolation transformer in the AC power line before the service.
- Be careful not to touch the rotation part (cooling fan, etc.) of this projector when you service with the upper
  case removed and the power supply turned ON.
- Observe the original lead dress during the service. If a short circuit is found, replace all the parts overheated
  or damaged by the short circuit.
- After the service, all the protective devices such as insulation barriers, insulation papers, shields, and isolation
  R-C combinations must be properly installed.
- After the service, check the leakage current to prevent the customer from getting an electric shock.

Performance

 Voltmeter
 (rms reading)

Table. 1

Fig. 1

Fig. 2

M1

M2

T1

T2

Isolation transformer

to power outlet

Measuring
circuit (Fig.1)

Multi Window

Processor

connection

M1

M2

Rs

Rb

Cs

10 kΩ ±0.1%

V

Vb

(V)

0.022μF
±1.0%

to T1
or T2
in FIG.2

Rs:1500 Ω ±0.1%
Cs:0.22μF ±1.0%
Rb:500 Ω ±0.1%

Weighted lekage current = Vb / 500 (A)

5

・

The specifications of the projector are as follows.

AC 100 V - 240 V, 50 Hz/60 Hz

430 W (5.0 A - 1.8 A)

0.5 W when [STANDBY MODE] is set to [ECO]
8 W when [STANDBY MODE] is set to [NORMAL] (when fan is stopped)

16.5 mm (0.65") (aspect ratio 16:9)

1-unit DLP chip, DLP type

Number of pixels 2 073 600 pixels (1 920 x 1 080 dots)

Fixed

Electric focus: F = 1.8, f = 11.9 mm

Hybrid light source (LED/laser diode)

3 000 lm (ANSI)

20 000:1

7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)

1.02 m (40") to 5.08 m (200")

16:9

[FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]

3.0 m (118-1/8")

Molded plastic

455 mm (17-29/32")

137 mm (5-13/32") (with minimum feet length)

409 mm (16-3/32")

Approx. 11.5 k

] (25.4 lbs.)

*2

35 dB

0 °C (32 °F) to 45 °C (113 °F)

20 % to 80 % (no condensation)

DC 3 V (AA/R6/LR6 battery x 2)

Within 15 m (49'2") (when operated directly in front of signal receiver)

117 

] (4.1 ozs.) (including batteries)

Width: 48 mm (1-7/8"), Height: 163 mm (6-13/32"), Depth: 24.5 mm (31/32")

*1  Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*2  Average value. Weight varies for each product.
*3  When using the projector at high altitudes (1 400 m (4 593') – 2 700 m (8 858') above sea level), the operating environment temperature will be 0 °C 

(32 °F) – 40 °C (104 °F). When the operating environment temperature reaches 35 °C (95 °F) or higher, the light output may be reduced to protect 
the projector.

6

・

Refer to “List of compatible signals” of operating instructions, for the types of video signals that can be used with the projector.

Horizontal: 15.75 kHz/15.63 kHz, Vertical: 50 Hz/60 Hz

Horizontal: 15 kHz to 100 kHz, Vertical: 24 Hz to 120 Hz
PIAS (Panasonic Intelligent Auto Scanning) system

 

f Dot clock frequency: 162 MHz or less

 

f 525i (480i)

Horizontal: 15.75 kHz, Vertical: 60 Hz

 

f 525p (480p)

Horizontal: 31.5 kHz, Vertical: 60 Hz

 

f 750 (720)/60p

Horizontal: 45 kHz, Vertical: 60 Hz

 

f 1125 (1035)/60i

Horizontal: 33.75 kHz, Vertical: 60 Hz

 

f 1125 (1080)/50i

Horizontal: 28.13 kHz, Vertical: 50 Hz

 

f 1125 (1080)/24sF

Horizontal: 27 kHz, Vertical: 48 Hz

 

f 1125 (1080)/30p

Horizontal: 33.75 kHz, Vertical: 30 Hz

 

f 1125 (1080)/50p

Horizontal: 56.25 kHz, Vertical: 50 Hz

 

f 625i (576i)

Horizontal: 15.63 kHz, Vertical: 50 Hz

 

f 625p (576p)

Horizontal: 31.25 kHz, Vertical: 50 Hz

 

f 750 (720)/50p

Horizontal: 37.5 kHz, Vertical: 50 Hz

 

f 1125 (1080)/60i

Horizontal: 33.75 kHz, Vertical: 60 Hz

 

f 1125 (1080)/24p

Horizontal: 27 kHz, Vertical: 24 Hz

 

f 1125 (1080)/25p

Horizontal: 28.13 kHz, Vertical: 25 Hz

 

f 1125 (1080)/60p

Horizontal: 67.5 kHz, Vertical: 60 Hz

525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,  
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p

 

f Displayable resolution: VGA to WUXGA (non-interlaced)

WUXGA signal supports only VESA CVT-RB (Reduced Blanking) signal.

 

f Dot clock frequency: 25 MHz to 162 MHz

525p (480p), 625p (576p), 750 (720)/60p, 750 (720)/50p,  
1125 (1080)/60i, 1125 (1080)/50i, 1125 (1080)/24p,  
1125 (1080)/24sF, 1125 (1080)/25p, 1125 (1080)/30p,  
1125 (1080)/60p, 1125 (1080)/50p

 

f Displayable resolution: VGA to WUXGA (non-interlaced)

WUXGA signal supports only VESA CVT-RB (Reduced Blanking) signal.

 

f Dot clock frequency: 25 MHz to 162 MHz

1 set, high-density D-Sub 15 p (female)

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)

SYNC/HD

TTL high impedance, automatic positive/negative 
polarity compatible

VD

TTL high impedance, automatic positive/negative 
polarity compatible

(SYNC/HD and VD do not support 3 value SYNC.)

Y: 1.0 V [p-p] including synchronization signal, P

B

P

R

: 0.7 V [p-p] 75 Ω

1 set, DVI-I 29 p

Single link, DVI 1.0 compliant, HDCP compatible

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)

SYNC/HD

TTL high impedance, automatic positive/negative 
polarity compatible

VD

TTL high impedance, automatic positive/negative 
polarity compatible

Y: 1.0 V [p-p] including synchronization signal, P

B

P

R

: 0.7 V [p-p] 75 Ω

1 set, HDMI 19 pin, HDCP compatible, Deep Color compatible

Linear PCM (Sampling frequency: 48 kHz/44.1 kHz/32 kHz)

1 set, Pin jack 1.0 V [p-p] 75 Ω

1 set, D-Sub 9 p (female), RS-232C compliant, for computer control

1 set, M3 stereo mini jack (monitor output, with stereo support) 0 V [rms] to 1.8 V [rms] (variable), output 
impedance 2.2 kΩ or lower

1 set, M3 stereo mini jack 0.5 V [rms], input impedance 22 kΩ or higher

1 set, for RJ-45 network, DIGITAL LINK connection, PJLink compatible, 100Base-TX

1 set, Mini DIN 3 p, for 3D IR transmitter connection
Power outlet: 5 V/Maximum 500 mA, Stereo synchronization signal: 3.3 V/Maximum 10 mA

 

f The model numbers of accessories and optional accessories are subject to change without notice.

7

1. The name of each part　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

INF-2

1. 1. Projector body

1. 2. Control panel

1. 3. Connecting terminals

1. 4. Remote control

1. 5. Lens shift adjustment mechanism

2. OSD Menu Navigation　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

INF-5

3. Service Mode　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

INF-9

3. 1. Setting to Service Mode

3. 2. Resetting to User Mode

3. 3. Function in Service Mode

4. External control　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

INF-12

4. 1. Control through SERIAL termanal

4. 2. Control through LAN terminal

5. Notification for service operation　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

INF-16

5. 1. Before service operation

5. 2  Service

5. 3. Initialization for menu lock password

6　Troubleshooting　　・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・

　

INF-18

6. 1. Optical block overview

6. 2. Shutdown system

6. 3. System log data acquisition method

6. 4. Troubleshooting