Panasonic PT-RZ12KE / PT-RS11K (serv.man3) Service Manual ▷ View online
INF-31
SECTION 1 SERVICE INFORMATION
<RZ12K/RS11K>
Bit
Error code (hex)
Self-test
indication Details
Probable cause
64
U
PP
ER
00000000 00000001
–
Not used
65
00000000 00000002
–
Not used
66
00000000 00000004
F11
Shutter error
Shutter operation is abnormal
67
00000000 00000008
–
Not used
68
00000000 00000010
U25
LD1 temperature error
External temperature is too high. Lack of cooling liquid
Cooling pump deterioration. Radiator clogged
Out of usage with high altitude
69
00000000 00000020
U26
LD2 temperature error
70
00000000 00000040
–
Not used
71
00000000 00000080
–
Not used
72
00000000 00000100
H14
LD1 temp sensor disconnected
LD1 temp sensor disconnected, disconnecting of connector (DR8)
73
00000000 00000200
H15
LD2 temp sensor disconnected
LD2 temp sensor disconnected, disconnecting of connector (RT15)
74
00000000 00000400
–
Not used
75
00000000 00000800
–
Not used
76
00000000 00001000
U16
LD1 temperature warning
External temperature is too high. Lack of cooling liquid
Cooling pump deterioration. Radiator clogged
Out of usage with high altitude
77
00000000 00002000
U17
LD2 temperature warning
78
00000000 00004000
–
Not used
79
00000000 00008000
–
Not used
80
00000000 00010000
F91
FPGA1 configuration error
Failure on signal processing block
81
00000000 00020000
F92
FPGA2/3 configuration error
82
00000000 00040000
F90
FPGA configuration error
83
00000000 00080000
FA9
CPLD configuration error
84
00000000 00100000
–
Not used
85
00000000 00200000
–
Not used
86
00000000 00400000
F96
Lens mounter operation error
Stepping motor operation failure
Position detection sensor failure
87
00000000 00800000
F61
LD1 driver communication error
Communication error with LD1 driver
88
00000000 01000000
F62
LD2 driver communication error
Communication error with LD2 driver
89
00000000 02000000
FA8
Disable of recovery for LD1 open failure
LD1 lighting failure
90
00000000 04000000
FC8
Disable of recovery for LD2 open failure
LD2 lighting failure
91
00000000 08000000
–
Not used
92
00000000 10000000
FL1
LD1 lighting failure
LD1 lighting failure
93
00000000 20000000
FL2
LD2 lighting failure
LD2 lighting failure
94
00000000 40000000
UA0
Power circuit temperature warning
Temperature of power circuit is to high.
95
00000000 80000000
–
Not used
96
00000001 00000000
F65
LD sub microprocessor error
Device failure on DR board.
97
00000002 00000000
UA4
Power circuit temperature error
temperature of power circuit is too high.
98
00000004 00000000
A08
Communication error with sub microprocessor
(R8)
Communication error with sub microprocessor.
99
00000008 00000000
A41
IIC communication error 1(RTC)
Device failure on signal processing block.
100
00000010 00000000
A42
IIC communication error 2 (EEPROM)
101
00000020 00000000
–
Not used
102
00000040 00000000
–
Not used
103
00000080 00000000
–
Not used
104
00000100 00000000
–
Not used
105
00000200 00000000
A47
IIC communication error 7 (EDID DIGITAL)
Device failure on signal processing block.
106
00000400 00000000
A48
IIC communication error 8 (EDID ANALOG)
107
00000800 00000000
A49
IIC communication error 9 (ADC1)
108
00001000 00000000
A50
IIC communication error 10 (ADC2)
109
00002000 00000000
A51
IIC communication error 11 (ACCELERATION
SENSOR)
110
00004000 00000000
A52
IIC communication error 12 (OPTICAL
SENSOR)
111
00008000 00000000
A53
IIC communication error 13 (HD BaseT)
112
00010000 00000000
A54
IIC communication error 14 (ATM SENSOR)
113
00020000 00000000
–
Not used
114
00040000 00000000
–
Not used
115
00080000 00000000
–
Not used
116
00100000 00000000
F81
FM-R TEST Fail
Abnormal boot mode on FM unit.
Error of memory test on FM unit.
117
00200000 00000000
F82
FM-G TEST Fail
118
00400000 00000000
F83
FM-B TEST Fail
119
00800000 00000000
A94
FPGA1 communication error
Failure on signal processing block.
120
01000000 00000000
A95
FPGA2 communication error
121
02000000 00000000
UA5
FPGA temperature error
Temperature of FPGA is too high.
122
04000000 00000000
A97
FM communication error
Communication error with FM unit.
123
08000000 00000000
UA1
FPGA temperature warning
Temperature of FPGA is too high.
124
10000000 00000000
–
Not used
125
20000000 00000000
–
Not used
126
40000000 00000000
FC2
FRC error
Program transfer error to FRC
127
80000000 00000000
FC0
Power microprocessor communication error
Communication error with power microprocessor.
INF-32
SECTION 1 SERVICE INFORMATION
<RZ12K/RS11K>
5. 4. Troubleshooting
* The letters in the left of inspection items indicate the P.C. Boards related to their respective descriptions.
* Please check items with the interlock switch on.
■ Power does not turn ON. ([STANDBY/ON] LED does not light in red)
■ Power does not turn ON. ([STANDBY/ON] LED blinks once)
Check the connection of each connector
PF5-PB1,PB3-G5,PB3-DG3,PB3-A1,PB2-G6
NG
Connect the cables firmly
Check rear cover mounting correctly?
NG
Connect (Install) rear cover firmly
G Check the voltage [3.3V] at pin-1 of connector [G5].
NG
PF
PB Replace the [PF] or [PB] P.C.Board
Check and replace [G] P.C. Board.
or
Check and replace [A] P.C.Board.
Check the connection of cable connectors.
[PB3] - [G5]
NG
Connect the cables firmly
G Check and replace the [G] P.C.Board
OK
OK
OK
OK
■ Power does not turn ON. ([STANDBY/ON] LED blinks 3 times)
Check the connection of each connector
PB2-G18, PB3-A1/DG3/G10, A2D-G2
NG
Connect the cables firmly
A Check and replace [A] P.C. Board.
A Check the voltage [3.3V] at pin 1 of connector [A1].
Check the voltage [5V] at pin 3 of connector [A1].
NG
PB Check and replace [PB] P.C. Board.
OK
OK
INF-33
SECTION 1 SERVICE INFORMATION
<RZ12K/RS11K>
■ Light source does not turn on. (Both of [LIGHT1,LIGHT2] LED blink 3 times)
■ Light source does not turn on. (Either of [LIGHT1,LIGHT2] LED blinks 3 times)
■ Light source does not turn on. (Either of [LIGHT1,LIGHT2] LED blinks twice)
Check the connection of each connector.
PF3/PF4–D1, G5/G6–D3, D2–DR2/DR5
DR1/DR3/DR4/DR6–LD
NG
Connect the cables firmly.
Check the connection of each connector.
PF3/PF4–D1, G5/G6–D3, D2–DR2/DR5
DR1/DR3/DR4/DR6–LD
NG
Connect the cables firmly.
Check up the failure part on the LD with the self-check or logs.
D
Check the driver input voltage.
Check the voltage [DC380V] between pin 1 and 3, and voltage
[DC16V] between pin 4 and 3 of connector [D1] at the lighting
mode.
NG
PF
PB
Replace [PF] or [PB] P.C.Board
D
Check the driver input voltage.
Check the voltage [DC380V] between pin 1 and 3, and voltage
[DC16V] between pin 4 and 3 of connector [D1] at the lighting
mode.
NG
PF
PB Replace [PF] or [PB] P.C.Board
D
Check the connection of each connector.
D2–DR2/DR5, DR1/DR3/DR4/DR6–LD
NG
Connect the cables firmly.
D
Check the driver input voltage.
Check the voltage [DC12V] at pin 13 of connector [D3] at the
lighting mode.
NG
G
Replace [G] P.C.Board
D
DR Replace [D] or [DR] P.C.Board
D
DR Replace [D] or [DR] P.C.Board
Replace appropriate LD unit.
OK
OK
OK
OK
OK
OK
OK
INF-34
SECTION 1 SERVICE INFORMATION
<RZ12K/RS11K>
■ No picture or abnormal picture is output
Check connection of each connector.
Check the input image other than solid black image.
Is the test pattern displayed?
Connect the cables firmly.
j
A Check the signal waveform at pin 20 of connector [A2] (ADG_
LVDSL_CKP).
NG
Follow the section "A-P.C.Board operation check"
A Check the voltage (3.3V) at pin 106 of connector [A2] (FM_RE-
SET).
NG
Follow the section "Main microprocessor operation check"
A Check the voltage (3.3V) at pin 107 of connector [A2]
(PWRGOOD2).
NG
Check IC3501 (Main CPU) and IC3515 (AND gate) and periph-
eral circuit, or replace [PF]/[PB]-P.C.Board.
Follow the section "DG/FM-P.C.Board operation check"
OK
OK
OK
OK
OK
NG
NG
NG
NG
NG
NG
NG
NG
NG
NG
NG
OK
Is a menu screen displayed ?
A Check IC3058 and peripheral circuit.
No image is displayed
j
NG
No image with VIDEO input.
Follow the section "VIDEO input check"
No image with Y/C input.
Follow the section "Y/C input check"
No image with RGB1 input.
Follow the section "RGB1 input check"
No image with RGB2 input.
Follow the section "RGB2 input check"
No image with DVI-D input.
Follow the section "DVI-D input check"
No image with HDMI input.
Follow the section "HDMI input check"
No image with DIGITAL LINK input.
Follow the section "DIGITAL LINK input check"
No image with SDI1 input.
Follow the section "SDI1 input check"
No image with SDI2 input.
Follow the section "SDI2 input check"
Click on the first or last page to see other PT-RZ12KE / PT-RS11K (serv.man3) service manuals if exist.