Panasonic PT-RZ120 (serv.man2) Service Manual ▷ View online
ADJ-4
SECTION 3 ADJUSTMENTS
< RZ120 >
1. 3. Wheel index adjustment
1. Enter the service mode, and select submenu [AUTO INDEX CALIBRATION] of [EXTRA OPTION].
2. Select [OK] from confirmation message and press the <ENTER> button.
3. Wheel index adjustment pattern is projected automatically, auto-adjustment is started.
4. When the adjustment is complete "AUTO INDEX CALIBRATION COMPLETE" message is displayed.
Press the <MENU> button to finish the adjustment.
LENS CALIBRATION:NORMAL
OK
CANCEL
EXECUTE
CHANGE
Proceed LENS CALIBRATION,
and return to HOME POSITION.
and return to HOME POSITION.
ENTER
LENS
LENS TYPE
LENS HOME POSITION
MANUAL
LENS CALIBRATION
MENU SELECT
EXECUTE
ENTER
1. 2. Lens calibration
1. Select sub menu [LENS] of [PROJECTOR SETUP] menu.
2. Select the [LENS CALIBRATION] and press the <ENTER> button.
3. The lens calibration confirmation window will appear. Select [OK] and
press the <ENTER> button.
4. Lens moves up, down, left and right and setup the lens moving limitation
and home position automatically.
5. After finishing the calibration, the display returns to main manu.
EXTRA OPTOPN
1/2
DYNAMIC GAMMA MODE
3DCMS
ON
ON
255
255
SELF CHECK
AUTO INDEX CALIBRATION
PW1 INDEX
PW2 INDEX
POWER OFF MESSAGE
ERROR OSD
MODEL
LIGHT ADJUST
MUTE TIME OFFSET
MENU SELECT
SHUTTER KEEP
OFF
DISABLE
255
CW INDEX
q
w
EXECUTE
ENTER
AUTO INDEX CALIBRATION
OK
CANCEL
EXECUTE
CHANGE
ENTER
AUTO INDEX CALIBRATION
PROGRESS
EXIT
MENU
AUTO INDEX CALIBRATION
PROGRESS
EXIT
MENU
AUTO INDEX CALIBRATION
COMPLETE
EXIT
MENU
ADJ-5
SECTION 3 ADJUSTMENTS
< RZ120 >
Error message
Probable cause
PW1 Sensor value is wrong
Measured value of luminance sensor is abnormal.
Replace the sensor and perform index adjustment again.
PW1 Sensor value is wrong
CW Sensor value is wrong
PW1 Adjustment was failed
Calculation error of PW1. Replace the PW1 and perform index adjustment again.
PW1 Sensor value is wrong
Calculation error of PW2. Replace the PW2 and perform index adjustment again.
CW Adjustment was failed
Calculation error of CW. Replace the CW and perform index adjustment again.
[When the message "AUTO INDEX CALIBRATION INCOMPLETE" is displayed]
AUTO INDEX CALIBRATION
INCOMPLETE
PW1 Sensor value is wrong
EXIT
MENU
1. 4. EEPROM data transfer
f
Data backup and restore can be done via the LAN terminal.
This function cannot be used with SERIAL terminal connection.
1. 4. 1. Equipment to be used
1. Computer : Use it for transferring of backup data.
2. Communication cable : LAN cable (When connecting directly, use a cross cable)
3. Service Software : [LogTool.exe (Ver2.0.0.8~)] Download from the projector service website.
1. 4. 2. Connection Preparations
1. Check the settings of the projector
1) Select the sub menu [DIGITAL LINK MODE] of main menu [NETWORK] and set it to [AUTO] or [ETHERNET].
2) Check the network IP address of the projector and take a note.
3) Set the IP address of computer to approximate (same network group) value of the projector IP address.
• If you have changed the each menu settings, please return settings to the original (customers) after work.
2. Connect the projector and the PC by using a communication cable.
LAN cable (straight)
LAN cable (straight)
Projector LAN
Computer
Hub
Connection example
1. 4. 3. Backup the EEPROM data (before PCB exchange)
1. Switch the projector to "Normal-Standby" mode (ON/STANDBY indicator is lighting in red).
2. Start up service software [LogTool.exe] with a computer.
ADJ-6
SECTION 3 ADJUSTMENTS
< RZ120 >
3. The projector connection setting window appears.
1) Select [Option] → [Password] to display the password input window.
2) Enter the service password and then click [OK] button.
①
②
③
①
③
②
4. Select [LAN] of connection method and setup the connection information to connect to the projector.
A In case of known IP address of projector
• Select [Manual] and setup the [IP address, Port (Command Port)] and then click [Connect] button.
ADJ-7
SECTION 3 ADJUSTMENTS
< RZ120 >
①
②
③
④
⑤
• After searching result, the available projectors are listed on the window as the below.
Check mark the projector for which you want to acquire the system log and then click [OK] button.
B In case of unknown IP address of projector
• Select [Search] and setup the [IP Address/subnet mask] to the same network of the projector and [Port(Command
port)] and then click [Search] button.
Click on the first or last page to see other PT-RZ120 (serv.man2) service manuals if exist.