DOWNLOAD Panasonic PT-DZ680U / PT-DZ680E / PT-DW640U / PT-DW640E / PT-DX610U / PT-DX610E (serv.man7) Service Manual ↓ Size: 33.46 MB | Pages: 80 in PDF or view online for FREE

INF - 5

* Some default setting vary by the selected input signal. 
* Sub-menu items vary according to the selected input signal.

INF - 6

2. Input "1565" by remote controller and press ENTER. Then it goes into the Service Mode.

3. Press MENU button on the main body or remote controller and the menu of Service Mode is displayed.

2. Input "0000" by remote controller and press ENTER. Then the Serviceman Mode is disabled.

3. Press MENU button on the main body or remote controller and the menu of User Mode is displayed.

"Extra Option" is added on main mane. 

  1. 3DCMS

・ Sets ON (Valid) / OFF (Invalid) of 3D-Color Management system.

  2. SELF CHECK

・ Each self check item is displayed.

①- Main microprocessor Software Version

 SELF CHECK

②- Sub microprocessor Software Version

①-

 MAIN

:R1.00.00

③- Network microprocessor Software Version

②-

 SUB

:R1.00

④- Formatter microprocessor Software Version

③-

 NETWORK

:R1.00

⑤- Intake Air Temperature (Celsius/Fahrenheit)

④-

 DDP

:04 00 0B

⑥- DMD Temperature (Celsius/Fahrenheit)

⑤-

 OK

AIR TEMP.  32/224

⑦- Exhaust Temperature (Celsius/Fahrenheit)

⑥-

 OK

DMD TEMP. 054/104

⑧- Airflow Sensor

⑦-

 OK

OUT TEMP. 025/153

(Sensor value / AD conversion value / Correction value)

⑧-

 OK

AIR FLOW  075/054/000

⑨- LAMP1 condition (Cumulative usage time/ON-OFF)

⑨-

 OK

LAMP1     0H  3OM ON

⑩- LAMP2 condition (Cumulative usage time/ON-OFF)

⑩-

 OK

LAMP2     0H  3OM ON

⑪- Fan condition  (1: Normal,  0: Stop)

⑪-

 OK

FAN       1111 1111 1

⑫-

 OK

COLOR WHEEL

⑬-

 OK

SHUTTER      0 [   0]

⑫- Color Wheel condition
⑬- Shutter condition  (Opening and shutting number of times [Failed number of times]

This model has Service Mode in addition to regular on screen menu (user mode).
This mode enables some menu settings for the service operation.

1. Press menu button of main body or remote controller and go to Main menu -> "Projector setup".
    Then go to sub menu and select "Service Password" and press ENTER.

1. Press menu button of main body or remote controller and go to Main menu -> "Projector setup".
    Then go to sub menu and select "Service Password" and press ENTER.

Radiator

Exhaust -L

Exhaust -R

Power

Ballast

Lamp -R

Lamp -L
Liquid Cooling 

CW

* When the item from 5 to 13 is abnormal last time

and shuts it down, the font of OK becomes red.

1.
2.
3.
4.
5.
6.
7.

INF - 7

  3. CW INDEX

・ When the color wheel is replaced, adjust the "Color Wheel Index Adjustment".

   Refer to the "SECTION 3. ADJUSTMENT PROCEDURE" about method.

  4. POWER OFF MESSAGE

・ Setting of the shutter function with standby operation

- SHUTTER KEEP: When push the standby key with shutter ON, keep the shutter mode. 

- SHUTTER OPEN: When push the standby key with shutter ON, open the shutter and display

                               the "Power OFF confirmation message". (Default setting)

  5. ERROR OSD

・ When do not watch the error instructions LED of the lamp by a rear projection, the errors of the lamp can be
  displayed in the OSD.

- ON: "Lamp error message" is displayed on OSD.

- OFF: Does not display the "Lamp error message" in OSD.

  6. MODEL

・ Set this when the A-P.C.Board is replaced.

* If you can copy EEPROM data from the old A-P.C.Board, this setting is unnecessary.

* This model setting is changed after turn power on and off.

  7. CLOG SENSOR CALIBRATION

・Calibrate the clogging sensor circuit.

  Execute this after EEPROM（IC3103/IC3104）/A-P.C.Board or Airflow sensor (M2-P.C.Board） is replaced.

 * Refer to the "SECTION3 (ADJUSTMENT PROCEDURE)" about method.

  1. "PICTURE" menu

The following one item is added.
・Ye MODULATE

When PICTURE MODE menu is displayed, adjustment can be done by ENTER button.

ON: Ye MODULATE function is active

OFF: Ye MODULATE function is not active

  2. "POSITION" menu

The following one item is added.
・DVI EQUALIZER

When noise appears with DVI input caused by length of cable or external device, set this item 

so that the noise decreases.

  2. "ADVANCED" menu.

The following 4 items are added.

* Following items do not usually change the setting.
・FRAME LOCK

Set this item when moving picture is disturbed with RGB input.

・480i SD

When non-standard signal of 480i/576i is inputted (AV amplifier, etc), synchronization might be disordered

 according to connected equipment. In this case, set 480i SD to ON.

・480p OS

When 480p/576p is received, aliasing noise (longitudinal striated beat noise) might be generated according to

connected equipment. In this case, set 480p OS to ON. However, the resolution decreases a little.

・H PLL

When non-standard signal is inputted (VCR, VHD, etc), horizontal synchronization might be disordered according

to connected equipment. In this case, set H PLL to OFF.

INF - 8

  3. "PROJECTOR SETUP" menu

1) The following items are added on "STATUS" sub menu (page2).

・FPGA VERSION -------- FPGA software version
・DDP VERSION ---------- Formatter software version
・BALLAST VERSION --- Ballast software version

2) The following items are added on "STATUS" sub menu (page5).

・TEMP(℃) -----------Intake air temperature / Exhaust air temperature

/ Optical module temperature

・AIR FLOW --------- Sensor value / AD conversion value
・VOLT ---------------- Voltage of LAMP1/LAMP2
・POWER -------------Power fan status (Rotational speed）
・OUT1 ---------------- Exhaust1 fan status (Rotational speed）
・OUT2 ---------------- Exhaust2 fan status (Rotational speed）
・LAMP1 -------------- Lamp1 fan status (Rotational speed）
・LAMP2 -------------- Lamp2 fan status (Rotational speed）
・BALLAST -----------Ballast fan status (Rotational speed）
・RADIATOR ---------Radiator fan status (Rotational speed）
・CW -------------------CW fan status (Rotational speed）
・LIQUID -------------- Liquid cooling fan status (Rotational speed）

3) The following item is added on "INITIALIZE" sub menu.

・SHUTTER COUNTER

When the mechanical shutter is replaced, initialize the shutter counter.

  4. "TEST PATTERN" menu

・ The following test patterns are added.

"CW index （Red and blue）", "Whole red", "Whole green", "Whole blue", "Whole cyan", "Whole magenta",

 "Whole yellow" and "Convergence (RGB bar)” patterns.