Panasonic PT-DZ21KU / PT-DZ21KE / PT-DS20KU / PT-DS20KE / PT-DW17KU / PT-DW17KE Service Manual ▷ View online
5. Select Microprocessor to update, and click [load] button.
6. Appoint the microcomputer software that took in a computer beforehand, and click [Open] button.
7. When load of the microcomputer software is completed, a checkmark and path and a version are displayed.
* When do not do update in Microprocessor Software which did load, exclude a checkmark of Microprocessor
to fall under.
Without a mistake, click a [Update] button.
ADJ - 10
8. Click [OK] button and start update.
9. If completion and a message are displayed, click [OK] button.
10. Click [EXIT]button, and please be finished.
* Reboot Projector, and please confirm whether the version of the Microprocessor Software is updated definitely,
with sub menu " STATUS" of the main menu " PROJECTOR SETUP" .
with sub menu " STATUS" of the main menu " PROJECTOR SETUP" .
While update it, Lamp1-4 indicator indicates as follows.
*Main ⇒ Lamp indicator 1-4, flashing red in order.
*Sub ⇒ Lamp indicator 1-4 all lit red.
*Network ⇒ Lamp indicator 1-4, flashing red in order.
*Formatter ⇒ Power indicator lit green.
Lamp indicator 1-4 all lit red.
*Main ⇒ Lamp indicator 1-4, flashing red in order.
*Sub ⇒ Lamp indicator 1-4 all lit red.
*Network ⇒ Lamp indicator 1-4, flashing red in order.
*Formatter ⇒ Power indicator lit green.
Lamp indicator 1-4 all lit red.
*Rewrite the same version of
software will be skipped.
software will be skipped.
ADJ - 11
2. 2. Update by the SERIAL terminal connection
(Main/Sub/Formatter)
2. 2. 1. Equipment to be used
1. Computer : Use it for the transfer of software.
2. Communication cable : D-sub 9pin (male/female RS-232C straight)
3. Service Software : [MainSubNet Update Tool.exe] Service software is downloaded from the projector service homepage.
4. Microprocessor Software: Please download the file from the projector service homepage to the PC.
2. 2. 2. Connection Preparations
2. 2. 3. Update procedure
1. Switch the projector to "Normal-Standby" mode (POWER indicator is Lighting in red).
2. Start up service software with a computer, select Model, and then click the [OK] button.
3. Select "Serial" in "Connection", and input the ID, Port, Baudrate, Parity , and click [Connection Check] button.
4. A result of the connection confirmation is displayed.
"Check: NG" ⇒ Come back to item 3., and please
confirm whether setting is right.
confirm whether setting is right.
"Check: OK" ⇒ Click a [OK] button and advance next.
2. Connect the "SERIAL IN" termanal of projector
and PC with a RS-232C cable.
and PC with a RS-232C cable.
1. Confirm the projector's ID, baudrate, prity and
take a memo.
take a memo.
* Set up a PC in advance, prevent be in the
standby/ shut-down state.
standby/ shut-down state.
Computer
Projector
RS-232C cable (streight)
ADJ - 12
5. Select Microprocessor to update, and click [load] button.
6. Appoint the microcomputer software that took in a computer beforehand, and click [Open] button.
7. When load of the microcomputer software is completed, a checkmark and path and a version are displayed.
* When do not do update in Microprocessor Software which did load, exclude a checkmark of Microprocessor
to fall under.
Without a mistake, click a [Update] button.
*Microcomputer software rewrite
of the network by serial terminal
connection is not possible.
of the network by serial terminal
connection is not possible.
ADJ - 13
Click on the first or last page to see other PT-DZ21KU / PT-DZ21KE / PT-DS20KU / PT-DS20KE / PT-DW17KU / PT-DW17KE service manuals if exist.