Panasonic PT-D3500U / PT-D3500E Service Manual ▷ View online
13
PT-D3500U / PT-D3500E
5 Using the Serial Terminals
SERIAL terminals which are on the side-mounted connection terminals conform to RS-232C standard. This projector can be
controlled by a PC which is connected as shown below.
controlled by a PC which is connected as shown below.
5.1. Examples of Connection
5.2. Pin Assignments and Signal Names
5.3. Communication Conditions (Factory Setting)
5.4. Basic Format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add
parameters according to the details of control.
parameters according to the details of control.
14
PT-D3500U / PT-D3500E
Attention
·
No command can be sent or received for 10 to 60 seconds after the lamp starts lighting. Try sending any command after
that period has elapsed.
that period has elapsed.
·
When sending several commands, be sure to wait for a response from the projector before sending the next command.
When sending commands without parameters, a colon (:) is not necessary.
When sending commands without parameters, a colon (:) is not necessary.
Note
·
If a wrong command parameter is sent, the projector will send an "ER401" command to the computer.
·
A projector ID supported on the RS-232C interface is ZZ (ALL) , 01 to 64 and 0A to 0Z.
·
If a command is sent with a projector ID specified, the projector will respond to the computer only in the following cases:
If it coincides with the projector ID,
ID specification is ZZ (ALL), or
ID specification is 0A to 0Z.
5.5. Procedure of Communication Condition Settings
(1)
Press the MENU button.
The MAIN MENU screen will be displayed.
The MAIN MENU screen will be displayed.
(2)
Press the
and
buttons to select “OPTION2”.
(3)
Press the ENTER button.
(4)
Press the
and
buttons to select “RS232C”.
(5)
Press the ENTER button.
The RS232C screen will be displayed.
The RS232C screen will be displayed.
(6)
Press the
and
buttons to select communication conditions.
(7)
Press the
and
buttons to confirm the setting..
(8)
Press the MENU button three times.
The on-screen indications disappear, and the system returns to the
normal screen.
The on-screen indications disappear, and the system returns to the
normal screen.
5.6. Control commands
5.6.1. Input Commands
Items
Commands:Parameters
Functions
Callback
Remarks
POWER
PON
POWER ON
PON
Calls back PON even if
REMOTE2 is effective.
REMOTE2 is effective.
POF
STAND-BY
POF
Calls back PON even if
REMOTE2 is effective.
REMOTE2 is effective.
FREEZE
OFZ:0
FREEZE key
0=OFF 1=ON
0=OFF 1=ON
OFZ:0
OFZ:1
OFZ:1
MENU
OMN
MENU key
OMN
15
PT-D3500U / PT-D3500E
Items
Commands:Parameters
Functions
Callback
Remarks
ENTER
OEN
ENTER key
OEN
CURSOR
OCU
UP key
OCU
OCD
DOWN key
OCD
OCL
LEFT key
OCL
OCR
RIGHT key
OCR
STANDARD
OST
STANDARD key
OST
AUTO SETUP
OAS
AUTO SETUP execution
OAS
SHUTTER
OSH:0
SHUTTER key
0=OFF 1=ON
0=OFF 1=ON
OSH:0
Calls back ER402 when
SHUTTER of REMOTE2 is ON.
SHUTTER of REMOTE2 is ON.
OSH:1
OSH:1
Calls back ER402 when
SHUTTER of REMOTE2 is OFF.
SHUTTER of REMOTE2 is OFF.
INPUT SELECT
IIS:RG1
RGB1
IIS:RG1
Calls back ER402 if the
input switch of REMOTE2 is
input switch of REMOTE2 is
available.
IIS:RG2
RGB2
IIS:RG2
IIS:VID
VIDEO
IIS:VID
IIS:SVD
S-VIDEO
IIS:SVD
IIS:DVI
DVI
IIS:DVI
FUNCTION1
FC1
FUNC1 key
FC1
ON SCREEN
OOS:0
OSD selection
0= OSD OFF 1=OSD ON
0= OSD OFF 1=OSD ON
OOS:0
Effective and invalidity
are the same as remote
are the same as remote
control OSD key.
OOS:1
OOS:1
NUMBER KEY
ONK:0
NUMBER key 0
ONK:0
ONK:1
NUMBER key 1
ONK:1
ONK:2
NUMBER key 2
ONK:2
ONK:3
NUMBER key 3
ONK:3
ONK:4
NUMBER key 4
ONK:4
ONK:5
NUMBER key 5
ONK:5
ONK:6
NUMBER key 6
ONK:6
ONK:7
NUMBER key 7
ONK:7
ONK:8
NUMBER key 8
ONK:8
ONK:9
NUMBER key 9
ONK:9
SYSTEM SEL
OSL
SYSTEM SELECTER key
OSL
5.6.2. Data setting Commands
Items
Commands:Parameters
Functions
Callback
Remarks
PICTURE MODE
VPM:NAT
Sets to NATURAL.
VPM:NAT
VPM:STD
Sets to STANDARD.
VPM:STD
VPM:DYN
Sets to DYNAMIC.
VPM:DYN
VPM:CIN
Sets to CINEMA.
VPM:CIN
VPM:GRA
Sets to GRAPHIC.
VPM:GRA
TV-SYSTEM
VSG:AT1
Sets to AUTO1.
VSG:AT1
Calls back ER401 when
receiving the signal
receiving the signal
that cannot be
switched.
switched.
VSG:AT2
Sets to AUTO2.
VSG:AT2
VSG:NTS
Sets to NTSC.
VSG:NTS
VSG:N44
Sets to NTSC4.43.
VSG:N44
VSG:PAL
Sets to PAL.
VSG:PAL
VSG:PAN
Sets to N-PAL.
VSG:PAN
VSG:PAM
Sets to M-PAL.
VSG:PAM
VSG:SEC
Sets to SECAM.
VSG:SEC
VSG:P60
Sets to PAL60.
VSG:P60
RGB/YPbPr
SELECT
SELECT
ORF:0
Sets to RGB.
ORF:0
Calls back ER401 when
receiving the signal
receiving the signal
that cannot be
switched.
switched.
ORF:1
Sets to YPbPr/YCbCr.
ORF:1
ORF:2
Sets to AUTO.
ORF:2
ASPECT
VSE:0
Sets to AUTO.
VSE:0
Calls back ER401 when
receiving the signal
receiving the signal
that cannot be
switched.
switched.
VSE:1
Sets to 4:3.
VSE:1
VSE:2
Sets to 16:9.
VSE:2
VSE:3
Sets to S4:3.
VSE:3
VOLUME
AVL:p1p2p3
Volume control
AVL:p1p2p3
p1p2p3: 000-063
MUTE
AMT:0
Sets to OFF.
AMT:0
Calls back AMT:0 when
REMOTE2 is effective
REMOTE2 is effective
and SHUTTER is OFF.
Calls back ER402 when
REMOTE2 is effective
Calls back ER402 when
REMOTE2 is effective
and SHUTTER is ON.
AMT:1
Sets to ON.
AMT:1
Calls back ER402 when
REMOTE2 is effective
and SHUTTER is OFF.
REMOTE2 is effective
and SHUTTER is OFF.
Calls back AMT:1 when
REMOTE2 is effective
REMOTE2 is effective
and SHUTTER is ON.
CONTRAST MODE
VCR:0
Sets to STANDARD.
VCR:0
VCR:1
Sets to HIGH.
VCR:1
LAMP POWER
OLP:0
LAMP POWER setting
0=HIGH 1=LOW
0=HIGH 1=LOW
OLP:0
Available in STANDBY
Calls back ER402 when
Calls back ER402 when
Long Life Lamp is
used.
used.
OLP:1
OLP:1
16
PT-D3500U / PT-D3500E
Click on the first or last page to see other PT-D3500U / PT-D3500E service manuals if exist.