Panasonic PT-CW240U / PT-CW240E / PT-CW240EA / PT-CW330U / PT-CW330E / PT-CW330EA / PT-CX300U / PT-CX300E / PT-CX300EA / PT-CW241RU / PT-CW241RE / PT-CW241REA / PT-CW331RU / PT-CW331RE / PT-CW331REA / PT-CX301RU / PT-CX301RE / PT-CX301REA (serv.man2) Service Manual ▷ View online
PT-CW240/PT-CX300/PT-CW330/PT-CW241R/PT-CX301R/PT-CW331R
2-15
2-7 Disassemble LAMP DRIVER
and and POWER board
1. Unscrew 4 screws (as red circles) to
disassemble the Lamp Driver Module.
Note:1. When assemble ,please arrange the
Interlock switch and lamp cable to
the notch (as blue square).
Interlock switch and lamp cable to
the notch (as blue square).
2. When assemble ,please arrange the
16Pin cable and 5Pin cable to the
Shileding notch(as green square)
16Pin cable and 5Pin cable to the
Shileding notch(as green square)
2. Unplug 1 connector (as yellow square).
PT-CW240/PT-CX300/PT-CW330/PT-CW241R/PT-CX301R/PT-CW331R
2-16
Tie band
3. Unscrew 1 screw (as green circle) to
disassemble the THERMAL SENSOR
board.
board.
4. Unplug 1 connector (as red square).
5. Unscrew 2 screw (as yellow circles).
Thermal Sensor
board
Depending on the products, the tie band
may be used to fix the LAMP DRIVER
board on the shield. In this case, use the
board on the shield. In this case, use the
tie band as shown in the picture to fix the
board.
board.
Band parts no.: H518SZ06G001
PT-CW240/PT-CX300/PT-CW330/PT-CW241R/PT-CX301R/PT-CW331R
2-17
6. Unhook 2 spacer hooks (as blue square)
to disassemble LAMP DRIVER board.
Spacer parts no: H518PE43H001
7
.Unplug 5 connectors (as green squares).
8. Unscrew 4 screws (as red circles) to
disassemble POWER board.
disassemble POWER board.
9.
Take off Mylar (as yellow square).
Lamp Driver
spacer
LVBS board
PT-CW240/PT-CX300/PT-CW330/PT-CW241R/PT-CX301R/PT-CW331R
2-18
2-8 Disassemble Speaker and
AC Inlet Bracket
1. Tear off the EMI TAPE (as red square)
and unscrew 3 screws (as red circles)
and unscrew 1 screw(as blue circle) to
and unscrew 1 screw(as blue circle) to
remove the right speaker module.
2.Unscrew 4 screws (as yellow circles) and
remove the Sponge (as yellow square).
remove the Sponge (as yellow square).
3.Disassemble Speaker.
4. Unscrew 3 screws (as yellow circles) to
disassemble AC Inlet Bracket .
Speaker
Click on the first or last page to see other PT-CW240U / PT-CW240E / PT-CW240EA / PT-CW330U / PT-CW330E / PT-CW330EA / PT-CX300U / PT-CX300E / PT-CX300EA / PT-CW241RU / PT-CW241RE / PT-CW241REA / PT-CW331RU / PT-CW331RE / PT-CW331REA / PT-CX301RU / PT-CX301RE / PT-CX301REA (serv.man2) service manuals if exist.