Panasonic TX-PR65VT20 Service Manual ▷ View online
9
Battery (Duration)
Coin-shaped lithium battery CR2032
(approx. 75 hours in continuous use of the battery made by Panasonic)
(approx. 75 hours in continuous use of the battery made by Panasonic)
Materials
Main body: Resin
Lens: Liquid crystal glass
Lens: Liquid crystal glass
Viewing range
within approx. 3.2 m from the front of the TV
Operating Conditions
0
°C - 40 °C
Dimensions (W
× H × D)
177 mm
× 46 mm × 174 mm
Mass (including battery)
63.0 g Net
Note
• Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
10
5 Technical Descriptions
5.1.
Service port (M3 mini Jack) Specifications
The Service port (M3 mini Jack) on the following TVs can use as the RS232C terminal which is a standard computer SERIAL inter-
face.
*This operation system should be used by the certified professional dealer.
face.
*This operation system should be used by the certified professional dealer.
PC Control of the TV
• The TV can be controlled by a personal computer when connected through an RS232C/ M3 mini jack conversion cable (not sup-
plied).
• The computer will require software which allows sending and receiving of control data through its SERIAL port.
Please see required parameters and commands below.
Communication parameters
Basic format for control data
The transmission of control data from the PC starts with a STX signal, followed by the command, the parameters, and lastly an
EXT signal in that order. If there are no parameters, then the parameter signal does not need to be sent.
*Please see other side regarding Commands and Parameters.
EXT signal in that order. If there are no parameters, then the parameter signal does not need to be sent.
*Please see other side regarding Commands and Parameters.
Connection
Notes:
• With standby mode, this TV responds to "PON” and “QPW” commands only.
• Wait for the response of the first command to come from this unit before sending the next command.
• If multiple commands are transmitted, be sure to keep intervals of 250 m sec.
• Wait for the response of the first command to come from this unit before sending the next command.
• If multiple commands are transmitted, be sure to keep intervals of 250 m sec.
Send the command again when the call back command is unusual.
• If an incorrect command is sent by mistake, this TV will send an “ER401” or “ER402” command back to the computer.
• This TV does not respond for 15 seconds when “PON” or “POF” commands are transmitted.
• Send “EXT” commands before sending “IMS:**” commands.
• This TV does not respond for 15 seconds when “PON” or “POF” commands are transmitted.
• Send “EXT” commands before sending “IMS:**” commands.
Signal level
RS-232C compliant
Synchronization method
Asynchronous
Baud rate
9600 bps
Parity None
Character length
8 bits
Stop bit
1 bit
Flow control
-
11
• MUTE commands ("AMT: 0" and "AMT: 1") and "AVL: ***" command are invalid in case of HDMI (CECIL) cooperation.
However AMT, AUK, AUDI commands is effective. (MUTE rotation (toggle), VOLUME UP and VOLUME DOWN controls are
possible.)
possible.)
Main, Input & Picture Control Command
Control
Command
Inquiry
Command
Call back
Command
Parameter
note
STANDARD
CONTROL
POWER ON
PON
QPW
QPW : *
"0"(OFF)/ "1"(ON)
POWER OFF
POF
VOL
(level)
AVL: ***
QAV
QAV : ***
"000" - "100"
(up)
AUU
(down)
AUD
MUTE
AMT (Toggle)
QAM
QAM : *
"0"(NO MUTED)
/ "1"(MUTED)
AMT: *
ASPECT
DAM: ****
QAS
QAS : **** "ZOOM"/"FULL"/
"JUST"/"NORM"/
"SELF"/"ZOM2"/
"ZOM3"/"SFUL"/
"ZOM3"/"SFUL"/
"14:9"
Except SD mode
DAM (Tog-
gle)
INPUT
SELECT
CH UP
CHU
--
--
--
CH DOWN
CHD
--
--
--
TV
IMS : TV
QMI
QMI : **
"TV"
TV network (Toggle)
Analogue TV
IMS : TVA
"TVA"
DVB-T
IMS : TVD
"TVD"
DVB-S/Other Sat
IMS : BS1
"BS1"
Freesat
IMS : BS2
"BS2"
DVB-C
IMS : CAB
"CAB"
Component 1
IMS : C1
"C1"
Component2
IMS : C2
"C2"
Video 1
IMS : V1
"V1"
Video 2
IMS : V2
"V2"
Video 3
IMS : V3
"V3"
S-Video 1
IMS : S1
"S1"
SCART Cable
S-Video 2
IMS : S2
"S2"
SCART Cable
HDMI 1
IMS : H1
"H1"
HDMI 2
IMS : H2
"H2"
HDMI 3
IMS : H3
"H3"
HDMI 4
IMS : H4
"H4"
PC
IMS : PC
"PC"
SD (photo viewer)
IMS : SP
"SP"
VIERA CAST
IMS : VC
"VC"
PICTURE
MODE
Vivid (Dynamic)
VPC : VVT
QPC
QPC : ***
"VVT"
Standard
VPC : STD
"STD"
THX/ True Cinema
VPC : THX
"THX"
THX : Except PC, JPEG, MOVIE & VIERA CAST
Cinema
VPC : CNM
"CNM"
Game
VPC : GAM
"GAM"
Photo
VPC : CST
"CST"
Only HDMI, JPEG, MOVIE & VIERA CAST
Pro1
VPC : PR1
"PR1"
When Advance (isfccc) menu is On.
Except VIERA CAST
Except VIERA CAST
Pro2
VPC : PR2
"PR2"
12
Else & Remote Controller Key Command
Control
Command
Inquiry
Command
Call back
Command
Parameter
note
Information
INF
--
QIF
QIF : *****
480i
480p
576i
576p
720p
720p
1080i
1080p
DIRECT CH
INPUT
0
ICH : 0
-
-
-
1
ICH : 1
-
-
-
2
ICH : 2
-
-
-
3
ICH : 3
-
-
-
4
ICH : 4
-
-
-
5
ICH : 5
-
-
-
6
ICH : 6
-
-
-
7
ICH : 7
-
-
-
8
ICH : 8
-
-
-
9
ICH : 9
-
-
-
MENU
FUNCTION
MENU
MEN
-
-
-
SELECT
SEL
-
-
-
RETURN
RTN
-
-
-
EXIT
EXT
-
-
-
ARROW LEFT
ARL
-
-
-
ARROW RIGHT
ARR
-
-
-
ARROW UP
ARU
-
-
-
ARROW DOWN
ARD
-
-
-
OPTION (SUB MENU)
SUB
-
-
-
RED
RED
-
-
-
GREEN
GRN
-
-
-
YELLOW
YEL
-
-
-
BLUE
BLU
-
-
-
VIERA TOOLS
VTL
-
-
-
Click on the first or last page to see other TX-PR65VT20 service manuals if exist.