DOWNLOAD Panasonic TH-65PB2E Service Manual ↓ Size: 4.56 MB | Pages: 54 in PDF or view online for FREE

29

TH-65PB2E

• Please register electronic pen, when electronic pen is

exchanged.

• There is a maximum in electronic pen's number of registra-

tion.

• Since electronic pen's registration information is memorized

by the electronic pen adapter, in electronic pen adapter
exchange, re-registration of electronic pen is required for it.
(It is unrelated in the registration information, A-Board, and
the main part of a display of an electronic pen)

• To disassemble P.C.B., wait for 1 minute after power was off

for discharge from electrolysis capacitors.

• Please remove the clamper and tape of cables beforehand.
•

,  ,  , ,  

and  

marks 

indicate 

screw 

positions.

1. Remove the screws (

×30 , 

×18  ) and M8 Cap (×4 )

and then remove the Rear Cover.

• There are two types of stamp of the outer peripheral screw

position of the Rear Cover, but use the screw all the same.

1. Disconnect the connectors (DS13, P9), and remove the

flexible cable from the connector (DS1).

2. Remove the screws and then remove the Slot Block.

1. Remove the Slot Block.

(Refer to Removal of Slot Block)

2. Turn over the Slot Block.
3. Remove the screws and then remove DS-Board.

1. Disconnect the connector (A37).
2. Remove 4 Hexagonal-Head screws, 4 screws ( ), 1

screw ( ), 1 screw ( ) and then remove the HX-Board
Block.

30

TH-65PB2E

3. Turn over the HX-Board Block.
4. Disconnect the connector (HX1).
5. Remove 2 Hexagonal-Head screws and 2 screws and

then remove HX-Board.

• Since a touch pen setup is come by [OFF] when A-Board is

exchanged, please set to [ON].

1. Remove the HX-Board Block.

(Refer to Removal of HX-Board)

2. Disconnect the connectors (A5, A11, A13, A16, A22,

A27), and remove the flexible cables from the connectors
(A1, A20, A31, A32, A33).

3. Remove the screws and then remove A-Board.

1. Remove the Clampers and then remove the Duct Barrier

(SC) Assy and Duct Barrier (SS) Assy.

2. Disconnect the Joint Connectors.

3. Remove the screws and then remove the Fan Block (A),

(B), (C).

4. Remove the screws and then remove the Fans (1, 2, 3, 4)

from the Fan Fixed Metal.

5. Remove the Sponge (Fan Corner) from the Fan.

6. Reassemble the Fans in reverse order.
7. Stick the Fan Sponges around the Fan.

The Fan Sponge is not re-usable.
Please use a new one when Fan exchange.

31

TH-65PB2E

1. Disconnect the connectors (P2, P6, P11, P35, P52, P56,

P58).

2. Remove 5 screws ( ).
3. Remove 1 screw ( ) and then remove P-Board (MAIN).

1. Disconnect the connectors (P9, P51, P55, P57).
2. Remove the screws and then remove P-Board (SUS).

1. Disconnect the connector (P9).
2. Remove 2 screws ( ) and then remove the AC Cord

Clamper A.

3. Remove 1 screw ( ) and then remove the AC Inlet Assy.

1. Disconnect the connector (H27).
2. Remove the screws and then remove the Speaker Termi-

nal Block.

3. Remove 4 hooks and then remove the Edge Saddle.
4. Remove 2 screws (A) and then remove H3-Board.

32

TH-65PB2E

• When fixing the flexible cables between SU-Board and Pan-

eland between SD-Board and Panel, press down the ends of
(the lock mechanism) lid of the connector and firmly closed.

• When only one side is pressed down and closed, since the

lid (lock mechanism part) is soft, there is a possibility of
becoming loose connection without a lid (lock mechanism
part) closing completely.

1. Disconnect the Joint Connector.

2. Remove the screws and then remove the Fan Block (A)

and Duct Barrier (SC) Assy.

3. Remove the flexible cables from the connectors

(SU1,SU2, SU3, SU4, SU5, SU11, SD1, SD2, SD3, SD4,
SD5, SD11).

4. Disconnect the connectors (SU41, SD42, SD46).
5. Remove 5 screws ( ).