DOWNLOAD Panasonic TH-50PF11EK Service Manual ↓ Size: 24.7 MB | Pages: 127 in PDF or view online for FREE

31

TH-50PF11EK

1. Set Aging pattern (white pattern signal) by IIC mode.
2. Set the picture controls as follows.

Picture menu: Standard
Picture: +25
Aspect: Full

3. Connect Oscilloscope to TPSC1 and adjust VR16602 for 250V ± 10V.

1. To remove P.C.B., wait 1 minute after power was off for discharge from electrolysis capacitors.

Adjust the following voltages with the multimeter.

*See the Panel Label.
Caution

Absolutely do not reduce Vsus voltage below Ve not to damage the P.C.B.

Test Point

Volume

Level

TPSC1 (SC)

VR16602 (SC)

250V ± 10V
at 100 

µ

s 

period on the down slope.

P.C.B.

Name

Test Point

Voltage

Volume

Remarks

P Board

Vsus

TPVSUS

Vsus ± 2V

VR251 (P)

*

SC Board

Vad

TPVAD

-140V ± 1V

VR16600 (SC)

Vscn

TPVSCN

Vad + 145V ± 4V

Fixed

Vset

TPVSET

325V + 7V, -9V

Fixed

SS Board

Ve

TPVE

Ve ± 1V

VR16000 (SS)

*

Vda

TPVDA

75V + 1V, -2V

Fixed

D, DS Board

White balance and Sub brightness for NTSC, PAL, HD, PC and 625i signals

DN Board

Set Market Select Number to correct destination by MS mode (See chap. 6.1.4)

32

TH-50PF11EK

33

TH-50PF11EK

Instrument Name

Connection

Remarks

• RGB VGA60 W / B pattern
• Color analyzer

(Minolta CA-100 or equivalent)

PC input
Panel surface

User setting: Normal
(Picture menu: STANDARD)

Procedure

Remarks

[Condition]

• Ensure aging is adequate.
• Make sure the front panel to be used on the final set is fitted. 
• Make sure a color signal is not being shown before adjustment.
• Put the color analyzer where there is little color variation.

[Adjustment]

1. Set COMPONET / RGB-IN SELECT to RGB.
2. Select the IIC mode “PANEL W / B Adj.” item.
3. Check that the color temperature is “COOL (Hi)”.
4. Output a white balance pattern.
5. Touch the signal receiver of color analyzer to the highlight window’s center.
6. Fix G drive at E0h and adjust B drive and R drive so x, y become the “Color temperature 

COOL (Hi)” in the below table.

7. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
8. Set color temperature to “NORMAL (Mid)”.
9. Fix G drive at E0h and adjust B drive and R drive so the highlight window’s x, y becomes 

the “Color temperature NORMAL (Mid)” in the below table.

10. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.

11. Set color temperature to “WARM (Low)”.

12. Set G drive to E0h and adjust B drive and R drive so the highlight window’s x, y become 

the “Color temperature WARM (Low)” shown in the below table.

13. Increase R / G / B together so the maximum drive value in R / G / B becomes FCh.
14. Copy the R drive, G drive and B drive data in NTSC, PAL DVI region.

Adjustment target
Hi-light: x ± 0.003 y ± 0.003
Hi-light is target of the number at drive adjustment in the hi-light windows.
Therefore, it is not target of the hi-light number at after adjustment white balance.

Picture Menu: Standard
Aspect: Full
Position and size: Normal

• “7” key : color temperature select.
• “9” key : Picture menu select.

• Highlight section Signal amplitude 75%

• Drive standard G: E0h

34

TH-50PF11EK