Panasonic CF-29NTQGZBM Service Manual ▷ View online
7-3
7.1.6.
Removing the KBD PCB, MDC
Modem and LCD Cable/MIC Frame
Modem and LCD Cable/MIC Frame
Figure 5
1. Remove the LCD Cable/MIC Frame.
2. Remove the two Screws. <H>
3. Disconnect the three Cable from three Connectors
2. Remove the two Screws. <H>
3. Disconnect the three Cable from three Connectors
(CN930, CN950, CN952).
4. Remove the KB PCB.
5. Remove the two Screws. <I>
6. Disconnect the Cable from Connector. (J2)
7. Remove the MDC Modem.
5. Remove the two Screws. <I>
6. Disconnect the Cable from Connector. (J2)
7. Remove the MDC Modem.
Screws <H>: DFHE5025XA
Screws <I>: DFHE5025XA
Screws <I>: DFHE5025XA
7.1.7.
Removing the DIMM Cover and
Bottom Cover
Bottom Cover
Figure 6
1. Remove the four Screws<J>, and remove the DIMM
Cover.
2. Remove the eight Screws<K> and the eight Screws<L>.
3. Disconnect the Cable from Connector (CN12).
3. Disconnect the Cable from Connector (CN12).
Screws <J>: DRQT26+D4FZLT
Screws <K>: DRQT26+D4FZLT
Screws <L>: DRSB3+8FKL
Screws <K>: DRQT26+D4FZLT
Screws <L>: DRSB3+8FKL
<H>
<H>
<I>
<I>
Connector CN950
(front side)
Connector CN930
(reverse side)
MDC
Modem
KBD PCB
Connector CN952
(reverse side)
to Connector
(CN950)
to Connector
(CN952)
LCD Cable/
MIC Frame
to Connector
(J2)
Connector J2
(reverse side)
Connector J1
(reverse side)
to Connector
(CN930)
<L>
<L>
<K>
<L>
<J>
<J>
<J>
<J>
<L>
<L>
<L>
<L>
<K>
<K>
<K>
<K>
<K>
<K>
<K>
DIMM Cover
Bottom Cover
Connector CN12
to Connector
(CN12)
<L>
DIMM Radiation
sheet
7-4
7.1.8.
Removing the Speaker
Figure 7
1. Remove the LCD Lamp
2. Remove the four Screws<M>, and remove the LAN Heat
2. Remove the four Screws<M>, and remove the LAN Heat
Plate, Speaker Angle and the Speaker.
3. Remove the two Screws<N>, and remove the Heat Pipe
Unit Bottom.
4. Remove the four Screws<O>, and remove the MP Eject
Lever.
5. Remove the Screw<P>, and remove the MP Eject
BOUSUI Plate and MP Eject Slide Ass’y.
Screws <M>: DXQT26+D4NLT
Screws <N>: DXYN+J6FNL
Screws <O>: DXYN26+F5NLT
Screw <P>: DXQT26+D4NLT
Screws <N>: DXYN+J6FNL
Screws <O>: DXYN26+F5NLT
Screw <P>: DXQT26+D4NLT
7.1.9.
Removing the Wireless Module and
SD PCB
SD PCB
Figure 8
1. Disconnect the Cable from Connector (CN2).
2. Remove the Wireless Module.
3. Remove the MINI PCI Protector Sheet and the CD Edge
2. Remove the Wireless Module.
3. Remove the MINI PCI Protector Sheet and the CD Edge
Sheet.
4. Remove the three Screws<Q>.
5. Disconnect the Cable from Connector (CN
5. Disconnect the Cable from Connector (CN
56).
6. Remove the SD PCB.
Screws <Q>: DFHE5025XA
<O>
<P>
<N>
<N>
<M>
<O>
<O>
<O>
<M>
<M>
<M>
MP Eject
Lever
MP Eject
BOUSUI
Plate
BOUSUI
Plate
LAN Heat
Plate
Heat Pipe Unit
Bottom
MP Eject Slide
Ass’y
Speaker
Speaker
Angle
Bottom Cover
LCD Lamp Sheet
Coil Cooling Sheet
MP Eject
Spring
Spring
to Connector
(CN2)
to Connector
(CN952)
Wireless Module
MINI PCI Protector
Sheet
CD Edge Sheet
Main PCB
Connector CN2
Connector CN???
to Connector
(CN
56)
SD PCB
<Q>
<Q>
<Q>
7-5
7.1.10. Removing the PAD SW FFC Cover
Figure 9
1. Remove the three Screws<R>, and remove the PAD SW
FFC Cover.
Screws <R>: DFHE5054XA
7.1.11. Removing Main PCB, EXT Antenna
PCB, PCMCIA Unit and RTC Battery
Figure 10
1. Remove the two Screws<S>.
2. Remove the two Screws<T-1>.
3. Remove the two Screws<U>.
4. Remove the four Screws<V>.
5. Remove the Screw<W>.
6. Remove the two Screws<X>.
7. Disconnect the six Cables from six Connectors.
2. Remove the two Screws<T-1>.
3. Remove the two Screws<U>.
4. Remove the four Screws<V>.
5. Remove the Screw<W>.
6. Remove the two Screws<X>.
7. Disconnect the six Cables from six Connectors.
(Main PCB: CN1, CN6, CN9, CN10, CN51, CN54)
(EXT Antenna: CN1)
(EXT Antenna: CN1)
8. Remove the EXT Antenna.
9. Remove the Main PCB.
9. Remove the Main PCB.
10. Disconnect the Cable from Connector (CN4).
11. Remove the RTC Battery
12. Remove the four Screws<T-2>, and remove the PCMCIA
Unit.
<R>
<R>
<R>
PAD SW FFC
Cover
Power Cable
Guard
<S>
<S>
<T-1>
<T-2>
<T-2>
<T-2>
<T-2>
<W>
<T-1>
EXT Antenna PCB
Connector
CN1
to Connector
(CN4)
RTC Battery
Connector CN10
(front side)
Connector CN51
(front side)
Connector CN6
(reverse side)
Connector CN9
(reverse side)
Connector CN1
(reverse side)
PCMCIA Unit
to Connector
(CN6)
to Connector
to Connector
(CN9)
to Connector
(CN950)
to Connector
(CN51)
to Connector
(CN54)
to Connector
(CN10)
Connector CN4
(reverse side)
Connector CN54
(reverse side)
Main PCB
<V>
<V>
<X>
<X>
<U>
<U>
<V>
(EXT Antenna CN1)
to Connector
(Main PCB CN1)
7-6
Screws <S>: DFHM5054XA
Screws <T-1>:DFHE5025XA
Screws <T-2>:DFHE5025XA
Screws <U>: DRQT2+G6FKL
Screw <V>: DRHM5104ZA
Screw <W>: DFHE5025ZA
Screw <X>: DRHM5117ZA
Screws <T-1>:DFHE5025XA
Screws <T-2>:DFHE5025XA
Screws <U>: DRQT2+G6FKL
Screw <V>: DRHM5104ZA
Screw <W>: DFHE5025ZA
Screw <X>: DRHM5117ZA
7.1.12. Remove the HDD Main FPC
1. Remove the Screws<Y>, and remove the Batt HDD CN
Angle.
2. Remove the Screw<Z>, the two Screws<a> and the two
Screws<b>.
3. Remove the HDD Main FPC.
Screw <Y>: DFHE5092ZA
Screw <Z>: DFHE5025ZA
Screws <a>: DRHM5104ZA
Screws <b>: DFHE5025XA
Screw <Z>: DFHE5025ZA
Screws <a>: DRHM5104ZA
Screws <b>: DFHE5025XA
7.1.13. Removing the TP PCB
Figure 11
1. Disconnect the three cables from three Connectors.
(CN800, CN801, CN803)
2. Remove the two Screws<c>, and remove the TP PCB.
Screws <c>: DRHM0002ZA
7.1.14. Removing the IO PCB
Figure 12
1. Remove the six Screws<d>, and remove the IO PCB.
Screws <d>: DFHE5058ZB
<Y>
<a>
<b>
<b>
<a>
Batt HDD
CN Angle
CN Angle
HDD Main
FPC
FPC
CN Spacer
<Z>
Battery Connector
HDD Connector
<c>
<c>
TP PBC
to Connector
(CN800)
to Connector
(CN801)
Connector CN801
Connector CN800
Connector CN803
to Connector
(CN803)
<d>
<d>
<d>
<d>
<d>
<d>
IO PCB
Click on the first or last page to see other CF-29NTQGZBM service manuals if exist.