Panasonic KX-TDE600RU Service Manual ▷ View online
37
KX-TDE600RU
7 Test Mode
7.1.
Utility
7.1.1.
Utility-Diagnosis
Performs diagnostic tests on cards installed in the PBX, to identify the source of problems. There are 2 types of test, Card Test and
Pair Port Test.
If any of the tests listed here returns the result "NG" ("No Good"), contact your dealer. Test results can be saved as a TXT-format
(text) file.
When testing is complete, any cards that were set to OUS status must be returned to INS status if they are to be used again.
Pair Port Test.
If any of the tests listed here returns the result "NG" ("No Good"), contact your dealer. Test results can be saved as a TXT-format
(text) file.
When testing is complete, any cards that were set to OUS status must be returned to INS status if they are to be used again.
7.1.1.1.
Card Test
Tests the relevant functions of a card to ensure that it is operating correctly. The tests carried out vary according to the type of
card being tested.
card being tested.
The tests that are performed on each card are as follows:
A check mark indicates that the test is available for that card.
A check mark indicates that the test is available for that card.
To perform a card test
1. From the Utility menu, select Diagnosis.
2. Click on the Status cell of the card to be tested, and set it to "OUS".
3. Click on the cell showing the card type.
2. Click on the Status cell of the card to be tested, and set it to "OUS".
3. Click on the cell showing the card type.
A new window will be displayed.
4. Select the Card Test option.
A new window will be displayed.
5. Click OK to perform the test(s).
The error report will be displayed. When all tests are completed, the words "Test End!" will be shown on the last line of the out-
put.
put.
6. Select an option:
• Click Capture if you want to save the displayed information.
1. Enter a file name, or select a file to overwrite.
2. Click Save.
2. Click Save.
• Click Cancel to return to the Diagnosis screen.
DHLC DLC SLC8 SLC16/
MSLC16
CSIF LCOT T1 E1 BRI PRI OPB E&M DID
IP-
GW4
(TDA
(TDA
0484)
IP-
GW16
IP-
EXT
Local loop back diagnosis
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Card CT bus diagnosis
X
X
X
X
X
X
X
X
X
X
X
X
X
X
DTMF Receive test port
X
X
X
X
X
PT loop back diagnosis
X
X
Caller ID Card DTMF Sending
Out Diagnosis
Out Diagnosis
X
DSP DTMF generator/receiver
diagnosis
diagnosis
X
X
DSP DTMF receiver diagnosis
X
X
Framer IC alarm signal detec-
tion diagnosis
tion diagnosis
X
X
X
Framer IC error detection diag-
nosis
nosis
X
X
X
CS-INF loop back diagnosis
X
Super frame synchronization
diagnosis
diagnosis
X
Caller ID card loop back diag-
nosis
nosis
X
Extension mode setting test
X
IP-GW H.323 call simulate
diagnosis
diagnosis
X
X
LAN loop back diagnosis
X
38
KX-TDE600RU
7.1.1.2.
Pair Port Test
Tests the combination of an extension port and trunk port to ensure that communication with the trunk port can be carried out
successfully.
The pair port test can be carried out using one LCOT card and one DHLC, SLC8, SLC16 or MSLC16 card.
successfully.
The pair port test can be carried out using one LCOT card and one DHLC, SLC8, SLC16 or MSLC16 card.
The tests that are performed are as follows:
To perform a pair port test
1. From the Utility menu, select Diagnosis.
2. Click on the Status cell of the extension card to be tested, and set it to "OUS".
3. Click on the cell showing the card type.
2. Click on the Status cell of the extension card to be tested, and set it to "OUS".
3. Click on the cell showing the card type.
A new window will be displayed.
4. Select the Pair Port Test option.
A new window will be displayed. The card you selected in Step 3 will be shown in the Extension Line Slot No. drop-down list.
5. From the CO Line Slot No. drop-down list, select the slot number of the trunk card you want to test.
6. From the CO Line Port No. drop-down list, select the port number of the trunk you want to test.
7. Click OK.
6. From the CO Line Port No. drop-down list, select the port number of the trunk you want to test.
7. Click OK.
The error report will be displayed.
8. Select an option:
• Click Capture if you want to save the displayed information.
1. Enter a file name, or select a file to overwrite.
2. Click Save.
2. Click Save.
• Click Cancel to return to the Diagnosis screen.
7.1.1.3.
Utility-File Transfer PC to PBX (SD Card)
Copies PBX system files (program files, data files and activation key files) from the connected PC to the SD memory card
installed in the PBX. Pre-existing files on the SD memory card are overwritten.
This option is only available at Installer level.
installed in the PBX. Pre-existing files on the SD memory card are overwritten.
This option is only available at Installer level.
The following types of files can be copied using this tool:
• Program files: These contain the programs used to operate cards within the PBX and CSs, acting as on-board drivers.
• Data files: These contain the initial configuration data for individual cards and settings.
• Activation Key files: These contain the activation keys used to enable the use of IP CO lines and IP telephones through Virtual
• Data files: These contain the initial configuration data for individual cards and settings.
• Activation Key files: These contain the activation keys used to enable the use of IP CO lines and IP telephones through Virtual
VoIP cards and upgrade the software.
Not all files that are copied using this tool are automatically made active. To install new program files, main system data, or acti-
vation key for software upgrade to the PBX, use the System Reset-Reset by the Command utility for PMMPR, DMSYS, and LIC
files. Use the Refresh Activation Key utility for other LIC files, and the SD Card File View and Load utility for all other files.
The PBX examines the header information of a file to determine 2 things: whether the file contains supported data, and which
system component the file applies to.
Only files whose header information matches that of a system file supported by the PBX can be transferred. Attempting to trans-
fer any other type of file results in an error message.
vation key for software upgrade to the PBX, use the System Reset-Reset by the Command utility for PMMPR, DMSYS, and LIC
files. Use the Refresh Activation Key utility for other LIC files, and the SD Card File View and Load utility for all other files.
The PBX examines the header information of a file to determine 2 things: whether the file contains supported data, and which
system component the file applies to.
Only files whose header information matches that of a system file supported by the PBX can be transferred. Attempting to trans-
fer any other type of file results in an error message.
The names of all files that can be stored on the SD memory card are as follows:
Main Program
*: PMMPR-file-format data that is transferred to the PBX from the PC is saved as "PMMPR_S".
Line current OFF (Ext->CO)
Line current from extension to trunk turns off.
Line current ON (Ext->CO)
Line current from extension to trunk turns on.
Off hook detection (CO->Ext)
Off-hook generation/detection from trunk to extension
DTMF detection (CO->Ext)
DTMF generation/detection from trunk to extension
DP detection (CO->Ext)
DP generation/detection from trunk to extension
BELL detection (Ext->CO)
BELL generation/detection from extension to trunk
Speech path (Ext->CO)
Speech path from extension to trunk
Speech path (CO->Ext)
Speech path from trunk to extension
Name on SD Memory Card
Corresponding Card
PMMPR
IPCMPR
PMMPR_S
IPCMPR*
39
KX-TDE600RU
LPR Program
CS Program
System Data
*: DMSYS-file-format data that is transferred to the PBX is saved as "DMSYS_S".
Language Data
Activation Key
Name on SD Memory Card
Corresponding Card
PCSINF
CSIF
PDHLC
DHLC8/DLC8/DLC16
PSLC
SLC8
PT1
T1
PIPGW
IP-GW4 (KX-TDA0480)
PIPGWH
IP-GW4 (KX-TDA0484)
PIPGW16
IP-GW16
PPRI23
PRI23
POPB3
OPB
PIPEXT
IP-EXT16
PVOIPEX
IP-EXT16
Name on SD Memory Card
Corresponding Card
PCS24G
CS using a CSIF card for 2.4 GHz Portable Station
PDCS24G
CS using a DHLC/DLC card for 2.4 GHz Portable Station
Name on SD Memory Card
Corresponding Card
DMSYS
IPCMPR
DMSYS_S
IPCMPR*
Name on SD Memory Card
Corresponding Card
DLNG0-DLNG1
PT
DVMLNG1-DVMLNG5
VPS (Display Guidance data)
Name on SD Memory Card
Corresponding Card
LIC00-LIC99
V-IPEXT32, V-SIPEXT32, V-IPGW16, V-SIPGW16
40
KX-TDE600RU
Default Value Data
To transfer files to the SD memory card
1. From the Utility menu, select File Transfer PC to PBX (SD Card).
The dialog box will be displayed.
2. Select the file to upload.
A window showing the upload progress will be displayed.
While transferring files to the SD memory card, the PBX automatically renames them according
to the header information.
A message will be displayed when the transfer is complete.
While transferring files to the SD memory card, the PBX automatically renames them according
to the header information.
A message will be displayed when the transfer is complete.
3. Click OK.
7.1.1.4.
Utility-File Transfer PBX (SD Card) to PC
Copies system data files from the SD memory card installed in the PBX to the connected PC.
This option is only available at Installer level.
This option is only available at Installer level.
The files that can be downloaded from the SD memory card are as follows:
Downloading the DMSYS system data file allows you to make a backup of the configuration of the PBX.
The error data files are snapshots of the configuration of the PBX taken automatically when a major error causes a system
reset. They can be analyzed by your dealer to identify the source of a problem. If there is only one error data file, its name will be
$SYSERR. If there is more than one file, the files will be numbered in chronological order, up to a maximum of 9 files.
The error data files are snapshots of the configuration of the PBX taken automatically when a major error causes a system
reset. They can be analyzed by your dealer to identify the source of a problem. If there is only one error data file, its name will be
$SYSERR. If there is more than one file, the files will be numbered in chronological order, up to a maximum of 9 files.
To transfer files to the PC
1. From the Utility menu, select File Transfer PBX (SD Card) to PC.
2. Select the file to download from the list of files on the SD memory card.
2. Select the file to download from the list of files on the SD memory card.
Only the files listed in the table above can be downloaded. Selecting any other file will cause an error message to be dis-
played.
played.
3. Click Transfer.
The Save dialog box will be displayed.
4. Navigate to the folder in which you want to save the file.
5. Enter a file name.
6. Click Save.
5. Enter a file name.
6. Click Save.
A window showing the download progress will be displayed.
A message will be displayed when the transfer is complete.
A message will be displayed when the transfer is complete.
7. Click OK.
Name on SD Memory Card
Corresponding Card
DMINI
IPCMPR
DMIDHLC
DHLC8
DMISLC
SLC8
DMIDLC
DLC8/DLC16
DMIPRI
PRI
DMICSINF
CSIF
DMILCOT
LCOT8/LCOT16
DMIT1
T1
DMIOPB3
OPB3
DMIEIO
EIO
DMIIPGW1
IP-GW4 (KX-TDA0480)
DMIIPGW2
IP-GW4 (KX-TDA0484)
DMIIPGW3
IP-GW16
DMIPRI23
PRI23
DMISLCLC
SLC16
DMIIPEXT
IP-EXT16
DMIVIPGW
V-IPGW16
DMIVSPGW
V-SIPGW16
DMIVIPEX
V-IPEXT32
DMIVSPEX
V-SIPEX32
File Name
File Type
DMSYS
System Data
$SYSERR
Error Data
$SYSERR1-$SYSERR9
LIC00-LIC99
LIC00-LIC99
Activation Key
Click on the first or last page to see other KX-TDE600RU service manuals if exist.