DOWNLOAD Panasonic KX-TDA0156CE Service Manual ↓ Size: 1.7 MB | Pages: 54 in PDF or view online for FREE

25

1. Set the CMD60 to MANUAL TEST.
2. Set the CMD60 TRAFFIC CARRIER to 5.
3. Press ACCEPT RFPI and SETUP CONNECT on the CMD60.
4. Check Power (NTP) : must be +20 to +24dBm
5. Press MODULATION.
6. Set Data Type to "FIG 31".
7. Check the Frequency Offset : must be 0±50kHz.
8.  Check the Deviation ( Max. ±B Field ) with Data Type "FIG.31" : must be ±320 to ±403kHz.
9. Check the Frequency Drift : must be 0 ±35kHz/ms.

10. Press MENU UP "

↑" on the CMD60.

11. Press POWER RAMP.

12. Check the Burst fits mask.
13. Press MENU UP "

↑" on the CMD60.

14. Press BER.
15. Obtain the sensitivity by slowly reducing the RF LEVEL until the BER falls below 1000ppm.

The sensitivity is the RF LEVEL reading at this point.
must be < -87 dBm.

16. Press MENU UP "

↑" on the CMD60.

17. Press BEARER RELEASE and disconnect power supply adaptor.

These tests can be repeated on Traffic Carrier 0 and 9.
Make sure to set all dip switches to OFF after RF test.

1. Remove the under cabinet (Refer to 7.1. DISASSEMBLY INSTRUCTION 1.)
2. Remove 2 antennas from CN900 and CN901 (Refer to 7.1. DISASSEMBLY INSTRUCTION 2.) 
3. Remove the P.C.B from upper cabinet  (Refer to 7.1. DISASSEMBLY INSTRUCTION 3.) 
4. Solder cable to ANT1(CN901) (Refer to figure)
5. CMD60 set up.

6. Set Dip switch pin 2 to pin 6 from OFF to ON.

7. Connect the PC to the CS by service JIG cable
8. Start up the PC and start the hyper terminal
9. Set the hyper terminal property as follows

TEST MODE

FP

CONFIG MENU

SIGN. PARAM

SCRAMBLE OFF
ANTENNA

0 ( at CN901 )

* If you solder cable to ANT2 ( CN900 ) , you should select "1" on the CMD60.

PMID

00000

TRAFFIC SLOT

4

TRAFFIC CARRIER

5

serial port setup 

Port

COM1

Bit per second

19200

Data bits

8

Parity

None

Stop bit

1

Flow control

Xon/Xoff

26

10. Supply a voltage to the TEL jack from the AC adaptor (KX-TCA1 / KX-A11) via power supply adaptor (PSZZ1TDA0142)

Description of RSSI Calibration Process
Text following "Command:" is the input command for the terminal connected to the CS.
Text following "Response:" is the terminal display response data.
Confirm the response before proceeding to the next step. If no response is set. Shut off power and repeat from the beginning.

1. Remove the under cabinet (Refer to 7.1. DISASSEMBLY INSTRUCTION 1.)
2. Remove 2 antennas from CN900 and CN901 (Refer to 7.1. DISASSEMBLY INSTRUCTION 2.) 
3. Remove the P.C.B from upper cabinet  (Refer to 7.1. DISASSEMBLY INSTRUCTION 3.) 
4. Solder cable to ANT1(CN901) (Refer to figure)
5. CMD60 set up.

6. Set Dip switch pin 2 to pin 6 from OFF to ON.

serial port setup 

check next check boxes
ASCII Receiving - Append line feeds to incoming line ends

  Warp lines that exceed terminal width                      

TEST MODE

FP

CONFIG MENU

SIGN. PARAM

SCRAMBLE OFF
ANTENNA

0 ( at CN901 )

* If you solder cable to ANT2 ( CN900 ) , you should select "1" on the CMD60.

PMID

00000

TRAFFIC SLOT

4

TRAFFIC CARRIER

0

27

7. Connect the PC to the CS by service JIG cable
8. Start up the PC and start the hyper terminal
9. Set the hyper terminal property as follows

10. Supply a voltage to the TEL jack from the AC adaptor (KX-TCA1 / KX-A11) via power supply adaptor (PSZZ1TDA0142)

Description of Modulation Calibration Process
Text following "Command:" is the input command for the terminal connected to the CS.
Text following "Response:" is the terminal display response data.
Confirm the response before proceeding to the next step. If no response is set. Shut off power and repeat from the beginning.

Make sure to set all DIP switches to OFF after adjustment.

serial port setup 

Port

COM1

Bit per second

19200

Data bits

8

Parity

None

Stop bit

1

Flow control

Xon/Xoff

serial port setup 

check next check boxes
ASCII Receiving - Append line feeds to incoming line ends

  Warp lines that exceed terminal width                      

28