Panasonic KX-NT630RU-B Service Manual ▷ View online
21
KX-NT630 Series
7 Test Mode
7.1.
Loopback Test Mode
This is for VoIP Communication Test Connection Chart.
7.1.1.
Preparation
Preparation device
• Unit for Test phone
• AC adaptor( or LAN cable and switching hub with PoE)
• AC adaptor( or LAN cable and switching hub with PoE)
Set up unit in test mode by key control
1. Connect power plug (AC adaptor/PoE).
2. Push [1][*][CONF] keys within 3 seconds after power on.
3. Wait until Ringer LED goes off. Then release the three keys.
2. Push [1][*][CONF] keys within 3 seconds after power on.
3. Wait until Ringer LED goes off. Then release the three keys.
*If "IPL start..."is displayed before "Ringer LED goes off, it fails in the setting for Test mode
Try again from Step.1
Try again from Step.1
4. Release keys.
5. After 10 seconds,"HOOK Test" is displayed on LCD.
6. Press "SP-phone" key 8 times slowly.
5. After 10 seconds,"HOOK Test" is displayed on LCD.
6. Press "SP-phone" key 8 times slowly.
"ACOUSTIC TEST" is displayed on LCD.
7.1.2.
Communication Test
It is set to Loopback Test mode to connect "Send signal" with "Receive signal" by inputting two number.
Input number is 6,7 and 8 and the mode is as follows
(I) : Input 6.SP-phoneMIC 7.HandsetMIC 8.HeadsetMIC
(O): Output 6.SP-phoneSP 7.HandsetSP 8.HeadsetSP
(I) : Input 6.SP-phoneMIC 7.HandsetMIC 8.HeadsetMIC
(O): Output 6.SP-phoneSP 7.HandsetSP 8.HeadsetSP
For example
1. Handset MIC
Handset SP
7 7
I:HsMic
O:HsSp
I:HsMic
O:HsSp
No sound
2. Handset MIC
SP-phone SP
7 6
I:HsMic
O:Sp
I:HsMic
O:Sp
OK
This result shows there is a problem in the signal line of Handset SP.
7.1.3.
Quit Test Mode for communication test
Just power off.
Headset
AC Adaptor : PQLV6508**
or Equivalent
or PoE(to LAN port)
22
KX-NT630 Series
7.2.
Functional Test Mode
This unit has some functional test modes.
By using this mode,you can easily check KEYs,LEDs and Others.
By using this mode,you can easily check KEYs,LEDs and Others.
7.2.1.
Preparation
Preparation devise:
• Unit for test phone.
• AC adaptor or Ethernet cable(PoE).
• AC adaptor or Ethernet cable(PoE).
Set up a unit in Test mode by key control
1. Push [1][*][CONF] keys within 3 seconds after power on.
2. Wait until Ringer LED goes off. Then release the three keys.
3. Then the LCD displays below
2. Wait until Ringer LED goes off. Then release the three keys.
3. Then the LCD displays below
7.2.2.
Functional Test mode lists
(HOOK TEST)
1. Then the LCD displays [HOOK Test].
(When skip [HOOK Test], Press SP-PHONE key.)
The RINGER LED is on/off according to HOOK switch.
Press SP-PHONE key.
The RINGER LED is on/off according to HOOK switch.
Press SP-PHONE key.
(HEADSET TEST)
2. Then the LCD displays [HEADSET Test].
(When skip [HEADSET Test], Press SP-PHONE key.)
The RINGER LED is on/off according to Headset detection.
Press SP-PHONE key.
The RINGER LED is on/off according to Headset detection.
Press SP-PHONE key.
(LCD TEST)
3. Then the LCD displays all dots.
Confirm CHARACTERS of LCD and backlight are on.
Press SP-PHONE key.
Press SP-PHONE key.
4. Then the LCD displays all dots.
Confirm CHARACTERS of LCD and backlight are off.
Press SP-PHONE key.
Press SP-PHONE key.
(KEY TEST)
5. Then the LCD displays [Key-Check Test]. Press all keys except SP-PHONE key.
Press SP-PHONE key.
6. Then the LCD displays [Key-Check OK].
Press SP-PHONE key.
23
KX-NT630 Series
(LEDs TEST)
7. Confirm all red LEDs turn on except intercom LED.
Press SP-PHONE key.
8. Confirm all red LEDs of CO line, intercom and Ringer change to green.
Press SP-PHONE key.
Then the Color TFT LCD displays the soft version.VER : xx.xxx].
Press SP-PHONE key.
Then the Color TFT LCD displays the soft version.VER : xx.xxx].
Press SP-PHONE key.
(ACOUSTIC TEST)
9. Then the LCD displays [RESONANCE test].
Confirm speaker is functioning.
Press SP-PHONE key.
Press SP-PHONE key.
10. Then the LCD displays [ACOUSTIC TEST].
This TEST mode is not used in service. Press SP-PHONE.
(INFORMATION)
11. Then the LCD displays [MODEL : KX-NT630].
Press SP-PHONE key.
12. Then the LCD displays [PASS : xxxx].
Press SP-PHONE key.
13. Then the LCD displays MAC address[MAC : xx:xx:xx:xx:xx:xx].
Press SP-PHONE key.
7.2.3.
Quit this Test Mode
It is OK to quit anytime during test mode. Disconnect AC adaptor or Ethernet cable(PoE).
24
KX-NT630 Series
8 Service Mode
8.1.
Factory Setting
8.1.1.
How to Clear User Setting
Units are reset to the Factory settings by this operation (Erase stored Phone numbers, Caller list and etc.).
This operation should not be performed for a usual repair.
This operation should not be performed for a usual repair.
To perform IP Reset
1. Connect power plug(AC adaptor/PoE)
2. Press "1","5","9"and ""*" at the same time within 3 seconds after power on.
2. Press "1","5","9"and ""*" at the same time within 3 seconds after power on.
Keep it until "factory reset" is displayed on LCD and Ringer LED is blink.
3. Release keys.
4. Power off.
4. Power off.
8.2.
How to Change MAC Address Label
(Procedure after Replacing the Main P.C.B.)
(Procedure after Replacing the Main P.C.B.)
When replacing the Main P.C.B., customer data shall be renewed before sticking the included MAC/Address.
8.2.1.
Replacing Main P.C.B.
Note:
(*1) : If you reuse defective P.C.B. for another repairing unit by repairing. Peel off the serial number and MAC address label on
original bottom cabinet and keep them with defective P.C.B..
(*2) : If you do not reuse the defective P.C.B. by repairing, scrap the P.C.B. to prevent the leak of customer's information in flash
ROM.
original bottom cabinet and keep them with defective P.C.B..
(*2) : If you do not reuse the defective P.C.B. by repairing, scrap the P.C.B. to prevent the leak of customer's information in flash
ROM.
MAC label
Main P.C.B.
New MAC address
New
Main P.C.B.
Main P.C.B. KIT from service part
Defective
Main P.C.B.
(*1)
(*2)
Waiting for repair
Scrap
Defective
Main
P.C.B.
Main
P.C.B.
Defective
Main
P.C.Board
Main
P.C.Board
Old MAC address
Click on the first or last page to see other KX-NT630RU-B service manuals if exist.