DOWNLOAD Panasonic KX-NS0131X Service Manual ↓ Size: 1.91 MB | Pages: 55 in PDF or view online for FREE

9

10

A stacking card to be installed in the MPR card slot of a KX-NCP500 or KX-NCP1000 to be used as a legacy gateway.
This card can be used only with PCMPR Software Version 002.01000 or later.

Accessories (included): Stacking cable x 1
User-supplied (not included): None

A lithium battery is used in the STACK-S (NCP) card. There is a risk of explosion if the battery is replaced with an incorrect type.
Dispose of used batteries according to the manufacturer’s instructions.

When installing or removing this card, the power switch must be turned off.

When stacking other PBXs with the KX-NS1000, place them well within reach of the stacking cable (2 m).

STACK-S (NCP) Card

Indication

Colour

Description

CARD STATUS Green

STACK-S (NCP) card status indication

• ON: INS (In Service)

Red

STACK-S (NCP) card status indication

• ON: Fault
• Flashing: OUS (Out of Service)

Indication

Colour

Description

RUN

Green

Status indication for legacy gateway

• ON:  Normal
• OFF:  Power  off
• Slow Flashing: Starting up
• Moderate Flashing: STACK-S (NCP) card error

LED flashing patterns are as follows:

• Slow Flashing: 60 times per minute
• Moderate Flashing: 120 times per minute

ALARM

Red

Alarm status indication for legacy gatewa

• ON:  Alarm
• OFF:  Normal

11

Before Installing the STACK-S (NCP) Card
Before you install a STACK-S (NCP) card in a PBX that has been used, make a backup of the system data in case you want to
use it later, with another PBX, etc. For details about making a backup, refer to the PC Programming Manual of the correspond-
ing PBX.

To use the PBX as a legacy gateway, the MPR card must be replaced with a STACK-S (NCP) card.

Follow the procedure below to install a STACK-S (NCP) card in the PBX.

1. Remove the 2 screws from the MPR card slot, and then remove the MPR card.
2. Insert the STACK-S (NCP) card into the MPR card slot along the guide rails.
3. Reinsert the 2 screws and turn them clockwise to fix the STACK-S (NCP) card in place.

• To remove the STACK-S (NCP) card, reverse the procedure above.
• Make sure the screws are tightened to earth the card securely.

For more details about installing and removing optional service cards, refer to the Installation Manual of the corresponding PBX.

MPR Card

MPR Card

KX-NCP500

KX-NCP1000

12

The connector map for inter-shelf connections is described in the table below.

Table 1 Connector map for connections between shelf #1

PinNo.

PinName

PinNo.

PinName

I/O

Function

1

CPU_STATUS0[0]_P

26

CPU_STATUS0[0]_N

O

SATCK_S CPU status #0

2

nSLF_PRS0_P

27

nSLF_PRS0_N

O

STACK_S connection detect

3

CPU_STATUS0[1]_N

28

CPU_STATUS0[1]_P

O

SATCK_S CPU status #1

4

GND

29

GND

-

GND

5

CCLINK0_N

30

CCLINK0_P

I/O

CIRCLINK data

6

GND

31

GND

-

GND

7

SHWU0[0]_P

32

SHWU0[0]_N

O

interconnect UP Highway #0

8

GND

33

GND

-

GND

9

SHWU0[1]_N

34

SHWU0[1]_P

O

interconnect UP Highway #1

10

GND

35

GND

-

GND

11

SHWU0[2]_P

36

SHWU0[2]_N

O

interconnect UP Highway #2

12

GND

37

GND

-

GND

13

CT_NETREF0_N

38

CT_NETREF0_P

O

Reference Clock

14

GND

39

GND

-

GND

15

SHW_nFH0_P

40

SHW_nFH0_N

I

Highway Frame Head 

16

GND

41

GND

-

GND

17

SHW_CLK0_N

42

SHW_CLK0_P

I

Highway Clock

18

GND

43

GND

-

GND

19

S_RESET0_P

44

S_RESET0_N

I

STACK_S reset

20

GND

45

GND

-

GND

21

S_RINGSYNC0_N

46

S_RINGSYNC0_P

I

RING_SYNC

22

S_ESLFID0_P

47

S_ESLFID0_N

I

SATCK_S Shelf Number

23

SHWD0[0]_P

48

SHWD0[0]_N

I

interconnect DOWN Highway #0

24

SHWD0[2]_N

49

SHWD0[2]_P

I

interconnect DOWN Highway #2

25

SHWD0[1]_N

50

SHWD0[1]_P

I

interconnect DOWN Highway #1