DOWNLOAD Panasonic KX-NCP500RU Service Manual ↓ Size: 5.46 MB | Pages: 127 in PDF or view online for FREE

37

The following number of cards can be installed in the Free Slots or Virtual Slots of the PBX.
Note:

• Any card that exceeds the capacity of the PBX will be ignored.
• When the PBX starts up with an invalid configuration, some cards will be ignored.

*1 One T1 or PRI23 card counts as 2 cards. When installing these cards, make sure that the number of these cards x 2 + the
number of the other cards does not exceed 8.

*1 Only 1 ECHO16 card can be mounted on each OPB3 card.

Card Type

Maximum Number

KX-NCP500

IPCMPR

1

Trunk Card

8

Virtual Trunk Card

2

V-IPGW16

1

Physical Trunk Card

Total 5 *1

LCOT4

3

T1

2

PRI23

2

Extension Card

8

Virtual Extension Card

4

V-IPEXT32

2

V-SIPEXT32

1

Physical Extension Card

Small Free Slots: Total 1

Regular Free Slots: Total 2

DHLC4

1

DLC8

1

DLC16

1

SLC8

1

SLC16

1

OPB3

2

Total

14

Card Type

KX-NCP500

Mounted on

DSP4

1

IPCMPR  Card

DSP16
DSP64
RMT

1

DPH4

4

OPB3 Card

ECHO16

2 *

MSG4

4

ESVM4
EIO4

4

38

The PBX supports the following number of CO lines and extensions.

For non-peer-to-peer calls via the DSP card, calls cannot be made or received when all of the card's resources are being used.

The following shows the number of each terminal equipment type supported by the PBX.

*1 KX-NT300 series and KX-NT265 (software version 2.00 or later only)

The supported card varies depending on the software version of your KX-NT265 IP-PT. To confirm the version, follow the proce-
dure below:

Type

KX-NCP500

Total Number of CO Lines

72

CO Line (Physical CO Line Card)

64

CO Line (Virtual CO Line Card)

8

Total Number of Extensions

68

Extension (Physical Extension Card)

28

Extension (Virtual Extension Card)

40

IP-PT and IP Softphone

40

SIP Extension

32

Terminal Equipment Type

KX-NCP500

Telephone

68

SLT

20

KX-DT300/KX-T7600 series DPT

24

Other DPT

6

APT

4

IP-PT*1

40

SIP Extension

32

DSS console

8

CS

4

High-density CS

2

PS

64

Voice Processing System (VPS)

2

Doorphone

16

Door Opener

16

External Sensor

16

External Relay

16

39

The pre-installed power supply unit (PSU) in each PBX supports a different load figure.

*1   Only the extension cards that can support SLTs count for the load figures.

PBX Model

Maximum Load Figure

KX-NCP500

28

Equipment Type

Load Figure

PT

KX-DT300 series DPT/KX-DT300 series DSS console/
KX-T7600 series DPT/KX-T7600 series DSS console

1

KX-T7560/KX-T7565 DPT

1

Other DPT/Other DSS console

4

APT

4

IP-PT

0

SIP Extension

0

Extension Card*1

DHLC4

4

SLC8

8

SLC16

16

CS (1 unit)

4

High-density CS (1 unit)

8

ISDN Extension

2

VPS (1 Port)

1

40

Performs diagnostic tests on cards installed in the PBX, to identify the source of problems.
If any of the tests listed here returns the result "NG" ("No Good"), contact your dealer. Test results can be saved as a TXT-format
(text) file.
When testing is complete, any cards that were set to OUS status must be returned to INS status if they are to be used again.

Tests the relevant functions of a card to ensure that it is operating correctly. The tests carried out vary according to the type of card
being tested.

The tests that are performed on each card are as follows:

1. From the Utility menu, select Diagnosis.
2. Click on the Status cell of the card to be tested, and set it to "OUS".
3. Click on the cell showing the card type.

A new window will be displayed.

4. Select the Card Test option.

A new window will be displayed.

5. Click OK to perform the test(s).

The error report will be displayed. When all tests are completed, the words "Test End!" will be shown on the last line of the out-
put.

6. Select an option:

• Click Capture if you want to save the displayed information.

1. Enter a file name, or select a file to overwrite.
2. Click Save.

• Click Cancel to return to the Diagnosis screen.

 DHLC

DLC

SLC

LCOT

T1

E1

BRI

PRI

OPB

Local loop back diagnosis

X

X

X

X

X

X

X

X

Card CT bus diagnosis

X

X

X

X

X

X

X

X

X

DTMF Receive test port

X

 

X

 

 

 

 

PT loop back diagnosis

X

X

 

 

 

 

 

DSP DTMF generator/receiver diagnosis

 

 

 

 

X

X

 

 

DSP 

DTMF 

receiver 

diagnosis

    

X

X

  

Framer IC alarm signal detection diagnosis

 

 

 

 

X

X

X

 

Framer IC error detection diagnosis

 

 

 

 

X

X

X

 

CS-INF loop back diagnosis

 

 

 

 

 

 

 

Caller ID card loop back diagnosis

 

 

 

X

 

 

 

Extension mode setting test

 

 

 

 

 

X