Panasonic KX-HDV430 Service Manual ▷ View online
21
KX-HDV430 Series
7.2.
Functional Test Mode
This unit has some functional test modes.
By using this mode,you can easily check KEYs,LEDs and Others.
By using this mode,you can easily check KEYs,LEDs and Others.
7.2.1.
Preparation
Preparation devise:
• Unit for test phone.
• AC adaptor or Ethernet cable(PoE).
• AC adaptor or Ethernet cable(PoE).
Set up a unit in Test mode by key control
1. Push [1] [TRANSFER] [*] and connect power plug (AC adaptor/PoE).
2. Wait until Ringer LED goes off. Then release the three keys.
3. Then the LCD displays below
2. Wait until Ringer LED goes off. Then release the three keys.
3. Then the LCD displays below
4. If "Touch- Check NG" displayed ,press SP-PHONE key and restart "Touch Panel Calibration" sequence.
Factory mode
Start Calibration
Please SP-PHONE once
Press "SP-PHONE" key
TouchPanel Calibration Start.
TouchPanel Calibration Start.
TSLIB calibration utility
Touch crosshair to calibrate
TSLIB calibration utility
Touch crosshair to calibrate
TSLIB calibration utility
Touch crosshair to calibrate
TSLIB calibration utility
Touch crosshair to calibrate
TSLIB calibration utility
Touch crosshair to calibrate
Touch-Check OK
1
2
3
4
5
Touch the cursor " " sequentially .
Touch the cursor " " sequentially again .
1
2
3
4
5
Touch-Check NG
22
KX-HDV430 Series
7.2.2.
Functional Test mode lists
(HOOK TEST)
1. Then the LCD displays [HOOK Test].
(When skip [HOOK Test], Press SP-PHONE key.)
The RINGER LED is on/off according to HOOK switch.
Press SP-PHONE key.
The RINGER LED is on/off according to HOOK switch.
Press SP-PHONE key.
(EHS TEST)
2. Then the LCD displays [EHS Test](test for plantronics EHS).
The RINGER LED is on : EHS unit connected
The RINGER LED is off : EHS unit unconnected
Press SP-PHONE key.
The RINGER LED is off : EHS unit unconnected
Press SP-PHONE key.
3. Then the LCD displays [Jabra Test](test for Jabra EHS).
The RINGER LED is on : Jabra unit connected
The RINGER LED is off : Jabraunit unconnected
Press SP-PHONE key.
The RINGER LED is off : Jabraunit unconnected
Press SP-PHONE key.
(LCD TEST)
4. Then the Color TFT LCD displays a white screen.
Press # key.
5. Then the Color TFT LCD displays a color bar test chart.
Press SP-PHONE key.
(CAMERA TEST)
6. Then the Color TFT LCD displays a video captured by the camera.
Press SP-PHONE key.
(KEY TEST)
7. Then the LCD displays [Key-Check Test] . Press all keys except SP-PHONE key.
Press SP-PHONE key.
8. Then the LCD displays [Key-Check OK].
Press SP-PHONE key.
Then the Color TFT LCD displays the soft version.VER : xx.xxx].
Press SP-PHONE key.
Then the Color TFT LCD displays the soft version.VER : xx.xxx].
Press SP-PHONE key.
(ACOUSTIC TEST)
9. Then the LCD displays [RESONANCE test].
Confirm speaker is functioning.
Press SP-PHONE key.
Press SP-PHONE key.
10. Then the LCD displays [ACOUSTIC TEST].
This TEST mode is not used in service. Press SP-PHONE.
(INFORMATION)
11. Then the LCD displays [MODEL : KX-HDV430][DEST : xx].
Press SP-PHONE key.
12. Then the LCD displays [PASS : xxxx].
Press SP-PHONE key.
13. Then the LCD displays MAC address[MAC : xx:xx:xx:xx:xx:xx].
Press SP-PHONE key.
7.2.3.
Quit this Test Mode
It is OK to quit anytime during test mode. Disconnect AC adaptor or Ethernet cable(PoE).
23
KX-HDV430 Series
8 Service Mode
8.1.
Factory Setting
8.1.1.
How to Clear User Setting
Units are reset to the Factory settings by this operation (Erase stored Phone numbers, Caller list and etc.).
This operation should not be performed for a usual repair.
This operation should not be performed for a usual repair.
To perform IP Reset
1. Connect power plug (AC adaptor or PoE Hub)
2. Press "1", "5", "9" and "*" at the same time until LCD displays [factory reset].
3. Wait for the reset process until it LCD displays [factory reset done].
4. Disconnect AC adaptor or Ethernet cable(PoE)
2. Press "1", "5", "9" and "*" at the same time until LCD displays [factory reset].
3. Wait for the reset process until it LCD displays [factory reset done].
4. Disconnect AC adaptor or Ethernet cable(PoE)
8.2.
How to Change MAC Address Label
(Procedure after Replacing the Main P.C.B.)
(Procedure after Replacing the Main P.C.B.)
When replacing the Main P.C.B., customer data shall be renewed before sticking the included MAC/Address.
8.2.1.
Replacing Main P.C.B.
MAC label
Main P.C.B.
New MAC address
New
Main P.C.B.
Main P.C.B. KIT from service part
Defective
Main P.C.B.
(*1)
(*2)
Waiting for repair
Scrap
Defective
Main
P.C.B.
Main
P.C.B.
Defective
Main
P.C.Board
Main
P.C.Board
Old MAC address
24
KX-HDV430 Series
8.2.2.
Attaching MAC Address Label
Attach the new MAC address label to the unit by placing over the old label.
Attach the new label
NEW MAC Address Label
Click on the first or last page to see other KX-HDV430 service manuals if exist.