DOWNLOAD Panasonic KX-HDV100RU / KX-HDV100RUB Service Manual ↓ Size: 4.77 MB | Pages: 54 in PDF or view online for FREE

13

Connect the Ethernet cable, the Handset Cord and the AC adaptor (Option) to the unit.

*2

*1

*1 Hub
*2 AC adaptor

The initial setting for the IP address is "DHCP—Auto". For information about your network
environment, contact your administrator. 

Use flexible cables without jack covers. Do not use cables with a hard coating that may tear or crack
when bent.
To prevent damage to the cables, use cables that do not protrude from the bottom of the base.
Connect the cables as shown in the following illustration.

14

This is for VoIP communication TEST.

Setting of Unit are required before communication test by Peer to Peer Mode. 
Refer to from 7.1.1 Preparation (P.14) to 7.1.2 Connection for Test (P.15) . 

• Unit (for Test phone and Reference phone): Each one
• Ethernet (LAN) cable

1. Push [2][6][*] and connect power plug (AC adaptor).
2. Wait until LCD displays [p2p mode]. Then release the three keys.
3. Then the LCD displays [P2P Mode]. Press OK.
4. Then it enters P2P Mode Setting. Choose the any mode.

Normal /Test1 (192.168.0.241)/Test2 (192.168.0.240)

5. Then the LCD displays [Set OK]. Remove and reconnect the plug.

Ethernet (LAN) cable

Customer's Unit

Reference Unit

15

1. Connect LAN port on Customer's unit (for reference) to LAN port on Reference unit (for test) with Ethernet (LAN) cable.

2. Plug the each unit's (for test and reference) AC adaptor.

1. Pick up handset (OFF Hook), then dial the following number (for test).

[0] [1] [2] [3]

2. Answer the call (OFF Hook) and confirm the voice and the display.
3. Disconnect the call by unit (for reference).
4. Pick up handset (OFF Hook), then dial the following number (for reference).

[0] [4] [5] [6]

5. Answer the call (OFF Hook) and confirm the voice and the display.
6. Disconnect the call by unit (for test).

After Communication Test, set the normal mode or Factory Setting (P.17).

Ethernet (LAN) cable

Customer's Unit
Tel no: 0456

Reference Unit
Tel no: 0123

IP: 192.168.0.241
TEST mode 1

IP: 192.168.0.240
TEST mode 2

Hub

AC adaptor

16

This unit has the KEYs and LEDs Test mode.
By using this mode, you can easily check KEYs and LEDs.

• Unit for Test phone
• AC adaptor 

1. Push [1] [TRANSFER] [*] and connect power plug (AC adaptor).
2. Wait until LCD displays [factory mode] and release the three keys.

1. Then the LCD displays [HOOK Test].

(When skip [HOOK Test], Press SP-PHONE key. )
The RINGER LED is on/off according to HOOK switch.
Press HOLD key.

2. Then the LCD displays all dots.

Confirm all dots displayed on the LCD.

3. Then the LCD displays [Key-Check Test] . Press all  keys except HOLD key.

Press HOLD key.

4. Then the LCD displays [Key-Check OK]. 

Confirm Ringer LED, Line1 LED, and Line2 LED is on.
Press HOLD key.

5. Then the LCD displays the software version.   

Ringer LED, Line1 LED, and Line2 LED is turn on with blue color. 
Press HOLD key.

6. Then the LCD displays [RESONANCE test]. 

Confirm speaker is functioning. 
Press HOLD key.

7. Then the LCD displays [ACOUSTIC TEST].  

This TEST mode is not used in service. Press HOLD.

8. Then the LCD displays [MODEL : KX-HDV100]. 

Press HOLD key.

9. Then the LCD displays [PASS : ffff].Press HOLD key. 
10. Then the LCD displays MAC address. Press HOLD key. 

It is OK to quit anytime during test mode. Disconnect AC adaptor.