Panasonic UB-T780BP Service Manual ▷ View online
21
(4) Fasten to the wall.
Using the remaining 4 screws, securely fasten the lower
potion of the board attachment to the wall.
potion of the board attachment to the wall.
(5) Reattach the lower frame cover.
Attach the lower frame cover to the lower side of the elite
Panaboard, and tighten both left and right screws so that the
cover does not protrude.
Panaboard, and tighten both left and right screws so that the
cover does not protrude.
(5)-a
Holding the lower frame cover with both hands, slide it
into the guides on both sides.
Holding the lower frame cover with both hands, slide it
into the guides on both sides.
(5)-b
Push the lower frame cover backward (1).
While keeping the lower frame cover's rib against the rear
side of the guides, push the lower frame cover upwards (2).
Push the lower frame cover backward (1).
While keeping the lower frame cover's rib against the rear
side of the guides, push the lower frame cover upwards (2).
22
(5)-c
Pull the lower frame cover (1).
While keeping the rear section of the lower frame cover
against the rear of the board, push the lower frame cover
up into the rear of the board (2).
Pull the lower frame cover (1).
While keeping the rear section of the lower frame cover
against the rear of the board, push the lower frame cover
up into the rear of the board (2).
(5)-d
Push the lower frame cover backward (1).
Push the entire lower frame cover up until both ends lock
into place (2). Fasten the 2 screws on the bottom side.
Push the lower frame cover backward (1).
Push the entire lower frame cover up until both ends lock
into place (2). Fasten the 2 screws on the bottom side.
Notice
Be careful not to cut yourself on the board attachments
when attaching the lower frame cover.
When mounting on a wall, do not hit or jolt the elite
Panaboard.
After mounting, gently apply some weight on the elite
Panaboard to make sure that it is securely fastened to
the wall.
(6) Wipe the screen board surface.
Gently wipe the screen board surface with a soft, moist cloth.
Gently wipe the screen board surface with a soft, moist cloth.
Notice
Do not use thinner, benzene, or abrasive chemicals to
clean. (Doing so can result in discoloration.)
Do not use thinner, benzene, or abrasive chemicals to
clean. (Doing so can result in discoloration.)
(7) Confirm that the elite Panaboard can operate.
See "Confirming the elite Panaboard Operation" (See 3.7.).
See "Confirming the elite Panaboard Operation" (See 3.7.).
23
3.6.3.
For Mounting on a Stand (Sold Separately)
(1) Hang the elite Panaboard on the stand with the screw
heads.
heads.
(2) Secure the elite Panaboard to the stand frame using the
two-wing bolts (M5 x 12 mm [1/2 in.] [2 count]) included
with the stand.
two-wing bolts (M5 x 12 mm [1/2 in.] [2 count]) included
with the stand.
Note:
When installing the elite Panaboard on the stand, you can
adjust its height to 4 different levels.
When changing the height, remove the left and right screws
from the back of the elite Panaboard, and securely insert them
at the desired height. Torque (greater than 1 N•m [10 kgf•cm
When installing the elite Panaboard on the stand, you can
adjust its height to 4 different levels.
When changing the height, remove the left and right screws
from the back of the elite Panaboard, and securely insert them
at the desired height. Torque (greater than 1 N•m [10 kgf•cm
(9 lbf•in.)]).
(3) Wipe the screen board surface.
Gently wipe the screen board surface with a soft, moist cloth.
Notice
Do not use thinner, benzene, or abrasive chemicals to
clean. (Doing so can result in discoloration.)
Do not use thinner, benzene, or abrasive chemicals to
clean. (Doing so can result in discoloration.)
(4) Confirm that the elite Panaboard can operate.
See "Confirming the elite Panaboard Operation" (See 3.7.).
See "Confirming the elite Panaboard Operation" (See 3.7.).
24
3.7.
Confirming the elite Panaboard Operation
After assembling the elite Panaboard, confirm that it operates properly by following the procedure below.
3.7.1.
Confirming the Interactive Features
1. Install the elite Panaboard software (refer to the Operating Instructions for this model.), and connect the included USB cable.
2. Confirm that the interactive features are operating correctly.
2. Confirm that the interactive features are operating correctly.
• If a projector is not available, confirm operation using only the elite Panaboard and computer.
• When the elite Panaboard software starts, the calibration screen is displayed on the computer screen.
• Perform tentative calibration by pressing the 5 points on the elite Panaboard with the electronic pen, as shown in the
• When the elite Panaboard software starts, the calibration screen is displayed on the computer screen.
• Perform tentative calibration by pressing the 5 points on the elite Panaboard with the electronic pen, as shown in the
illustration below.
For precise adjustment, it is necessary to use a projector.
For precise adjustment, it is necessary to use a projector.
• With the elite Panaboard software running, enter White Background mode and select the marker tool. Confirm operation by
writing on the screen board with the electronic pen and checking that the writing is displayed on the computer's screen. (Your
writing with the electronic pen will not appear on the screen board itself.)
writing with the electronic pen will not appear on the screen board itself.)
3.8.
Repackaging
To repackage the elite Panaboard, perform the steps in the section 3.6 “Assembling the elite Panaboard” in reverse.
Package the unit as depicted in the diagram in the section 3.5 “Preparing for Removing the elite Panaboard from Its Packaging”.
Package the unit as depicted in the diagram in the section 3.5 “Preparing for Removing the elite Panaboard from Its Packaging”.
Note
• When handling the screen board, hold it by the frame and not the screen board itself. (Holding the screen board can result in
the damage.)
Action
Checkpoints
Operation
Measure
1
Connect to a
computer using a
USB cable.
computer using a
USB cable.
Green LED lights.
(Normal operation)
Green LED does not light, or red LED is blinking.
Check the USB cable.
• Check if the USB cable is connected properly.
• Disconnect the USB cable from the computer, and then
• Disconnect the USB cable from the computer, and then
connect it again.
Click on the first or last page to see other UB-T780BP service manuals if exist.