Panasonic UB-T760 Service Manual ▷ View online
37
UB-T760
6.4.5.
AC Inlet
Before performing the following steps, remove the following parts.
• Lower Front Cover, Control - Power Cover Front, Control PCB Cover Plate and Power Box Cover Plate (refer to the section 6.1
“LED Board and Control Board”).
• Side Cover L (refer to the section 6.4.1 “Side Cover L, Upper Front Cover and Side Cover R”).
1. Remove the screw (A) and ground harness.
2. Disconnect the inlet harness.
3. Remove the 2 screws (B) and AC switch unit.
2. Disconnect the inlet harness.
3. Remove the 2 screws (B) and AC switch unit.
4. Remove the 3 screws (C) and control - power cover back.
5. Remove the 3 screws (D) and AC inlet assembly
5. Remove the 3 screws (D) and AC inlet assembly
38
UB-T760
6.5.
Electronic Pen
1.
Remove the battery cover.
2.
Remove the battery.
3.
Remove the screw.
4.
Separate the cover from the base cover while pushing the base cover as shown in the following figure.
5.
Remove the penpoint from the penpoint shaft.
6.
Remove the film cover and penpoint shaft.
39
UB-T760
Caution:
The FPC is latched to the connector CN2 by the clamper.
When disconnecting the FPC from the connector CN2, release the clamper from the connector base by sliding it in the
arrow direction using tweezers, then disconnect the FPC.
When disconnecting the FPC from the connector CN2, release the clamper from the connector base by sliding it in the
arrow direction using tweezers, then disconnect the FPC.
6.5.1.
Film Base Assembly
7.
Remove the film base assembly while disconnecting the FPC and harness from the connectors on the pen board.
8.
The battery terminal end engages with the opening of base cover. Remove the pen board while rotating it in the direction of the arrow to
release the battery terminal end from the opening. (Figure-1)
release the battery terminal end from the opening. (Figure-1)
9.
Remove the pen bottom. (Figure-2)
1.
Remove the snap ring, then separate the FPC assembly from the film base.
40
UB-T760
7 Measurements and Adjustments
7.1.
Adjustment for Electronic Pen
This adjustment is required when replacing, handling or servicing the following parts.
1. Pen Board in the Electronic Pen
2. Individual parts on the Pen Board
3. Ultrasonic Film of the Electronic Pen
2. Individual parts on the Pen Board
3. Ultrasonic Film of the Electronic Pen
7.1.1.
Requirement for Adjustment
The following are required for adjustment. Before performing the adjustment, prepare the following PC system, software, cable, etc.
7.1.2.
Installation of elite Panaboard Adjustment Software
Before performing the Pen Adjustment or Receiver Level Adjustment, the elite Panaboard Software and elite Panaboard Adjust-
ment Software must be installed. Install the elite Panaboard Adjustment Software, performing the following steps:
ment Software must be installed. Install the elite Panaboard Adjustment Software, performing the following steps:
Item
Required
Sub Item
Specification or Description
System
PC (Computer)
IBM
®
PC/AT or compatible with a CD-ROM drive
CPU
Pentium
®
4 processor or later
USB Port
Full Speed USB 2.0 (This Unit does not support Hi-Speed USB 2.0.)
Operating system
Windows
®
2000 (Microsoft
®
Windows
®
2000 operating system)
Windows
®
XP (Microsoft
®
Windows
®
XP operating system): 32 bits
Windows Vista
®
(Microsoft
®
Windows Vista
®
operating system): 32 bits
Memory
Windows
®
2000: 256 MB or greater
Windows
®
XP: 512 MB or greater
Windows Vista
®
: 512 MB or greater
Hard Disk
200 MB or more free space
Software
elite Panaboard Software
elite Panaboard Software with CD-ROM included with the elite Panaboard
elite Panaboard Adjustment Software
Version 2.0 or higher
Cable
USB Cable
Supplied with the product.
Special Interface Cable
Available as service part (Refer to Section 13.4 Tool.)
Other
Adjusted elite Panaboard
Working well
Step
Operation
1
Install the elite Panaboard Software.
2
Execute “EPA1000.EXE” of the
elite Panaboard
Adjustment Software.
3
Install the software, following the instructions on the display.
4
When you complete the software installation, the “
elite Panaboard
Adjustment Software” will be added to the program
menu.
Click on the first or last page to see other UB-T760 service manuals if exist.