DOWNLOAD Panasonic UB-T760 Service Manual ↓ Size: 2.15 MB | Pages: 81 in PDF or view online for FREE

17

<For Wall Mounting>
1. Loosely wrap the power cord with the cable tie, and plug the

power cord into the AC inlet.

• Connect the power cord to the elite Panaboard before install-

ing on a wall.

2. Insert the end of the cable tie into the cable tie fastening hole on 

the lower frame cover.

3. Pull the loose end of the cable tie to tighten it, and install the 

power cord depending on the location of the outlet, as illustrated 
in the following diagrams.

• When attaching the power cord downward.

• When attaching the power cord along the lower side of the

elite Panaboard.

4. Hang the elite Panaboard on the wall mounting plates with the

screw heads.

18

5. Remove the lower frame cover.

Remove the left and right screws, and then remove the lower
frame cover from the main unit of the elite Panaboard.

6. Remove the 4 latches from the board attachment by pushing them

towards the rear.

7. Fasten to the wall.

Using the remaining 4 screws, securely fasten the lower portion of
the board attachment to the wall.

8. Reattach the lower frame cover.

Attach the lower frame cover to the lower side of the elite Pana-
board, and tighten both left and right screws so that the cover
does not protrude.

a. Holding the lower frame cover with both hands, slide it into the

guides on both sides.

b. Push the lower frame cover backward (1).

While keeping the lower frame cover’s rib against the rear side of
the guides, push the lower frame cover upwards (2).

19

•

Be careful not to cut yourself on the board attachments when attach-
ing the lower frame cover.

•

When mounting on a wall, do not hit or jolt the elite Panaboard.

•

After mounting, gently apply some weight on the elite Panaboard to
make sure that it is securely fastened to the wall.

•

After installation is complete, use the included cable holder to man-
age the power cord and USB cable.

•

Do not use thinner, benzine, or abrasive chemicals to clean. (Doing
so can result in discoloration.)

•

Do not wipe the screen board with a dry cloth. (Doing so can cause
static electricity build-up.)

c. Push the lower frame cover (1).

While keeping the rear section of the lower frame cover against
the rear of the board, push the lower frame cover up into the rear
of the board (2).

d. Push the lower frame cover backward (1).

Push the entire lower frame cover up until both ends lock into
place (2). Fasten the 2 screws on the bottom side.

9. Wipe the screen board surface.

Gently wipe the screen board surface with a soft, moist cloth.

10. Confirm that the elite Panaboard can operate. (Refer to the sec-

tion 3.7 Confirming the elite Panaboard Operation.)

20

After assembling the elite Panaboard, confirm that it operates properly by following the procedure below.

1. Install the elite Panaboard software (refer to the Operating Instructions for this model.), and connect the included USB cable.
2. Confirm that the interactive features are operating correctly.

• If a projector is not available, confirm operation using only the elite Panaboard and computer.
• When the elite Panaboard software starts, the calibration screen is displayed on the computer screen.
• Perform tentative calibration by pressing the 4 points on the elite Panaboard with the electronic pen, as shown in the illustra-

tion below.
For precise adjustment, it is necessary to use a projector.

• With the elite Panaboard software running, enter White Background mode and select the marker tool. Confirm operation by

writing on the screen board with the electronic pen and checking that the writing is displayed on the computer's screen. (Your
writing with the electronic pen will not appear on the screen board itself.)

To repackage the elite Panaboard, perform the steps 1 - 3 in the section 3.6 “Assembling the elite Panaboard” in reverse.
Package the unit as depicted in the diagram in the section 3.5 “Preparing for Removing the elite Panaboard from Its Packaging”.
Note

• When handling the screen board, hold it by the frame and not the screen board itself. (Holding the screen board can result in the

damage.)

1

Turn on the power

Green LED lights.

(Normal operation)

Green LED does not light, or red LED is blinking.

Check the power cord. Refer to section 3.6 “Assembling the
elite Panaboard”, step1