Panasonic KV-S3065CL / KV-S3065CW (serv.man4) Service Manual ▷ View online
Error Code
Possible Cause
Check Point
Remarks
Classified Code
ST1
ST2
ST3
ST4
F62
(Back side gain
adjustment error)
(Back side gain
adjustment error)
52
00
00
00
1. Image Sensor Cover (B) is dirty.
Clean the cover surface. (See 7.2.)
2. CIS (B) lamp does not light.
1.
Execute CIS Level test in Sec.9.3.6 to
check the peak level.
check the peak level.
2.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
CIS (B) to Lamp Drive (B) Board
b.
Lamp Drive (B) Board to CN5004
(POWER RELAY Board)
(POWER RELAY Board)
c.
CN5002 (POWER RELAY Board) to
CN4008 (DRIVE Board)
CN4008 (DRIVE Board)
d.
CN4001 (DRIVE Board) to CN5033
(POWER RELAY Board)
(POWER RELAY Board)
e.
CN5032 (POWER RELAY Board) to
CN1012 (CONTROL Board)
CN1012 (CONTROL Board)
f.
CN5001 (POWER RELAY Board) to
CN4005 (DRIVE Board)
CN4005 (DRIVE Board)
g.
CN4003 (DRIVE Board) to CN802
(POWER Board)
(POWER Board)
3.
Check the lamp control signals to the CIS
(B)
(B)
→ CN5004-1
st
pin: 24 V
→ CN5004-2
nd
pin: 5 V
(When lamp is ON)
4.
Replace faulty parts or boards.
3. Pixel data from CIS (B) or image
processing circuit have some
problems.
processing circuit have some
problems.
1.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
CIS (B) to CN3006 (CIS (B) RELAY
Board): Only for KV-S3065CW
Series
Board): Only for KV-S3065CW
Series
b.
CIS (B) to CN3007 (CIS (B) RELAY
Board): Only for KV-S3065CL Series
Board): Only for KV-S3065CL Series
c.
CN3004 (CIS (B) RELAY Board) to
CN1004 (CONTROL Board)
CN1004 (CONTROL Board)
d.
CN3005 (CIS (B) RELAY Board) to
CN1005 (CONTROL Board)
CN1005 (CONTROL Board)
e.
CN1000 (CONTROL Board) to
CN2000 (INTERFACE Board)
CN2000 (INTERFACE Board)
2.
Check the following CIS timing signals on
the CIS (B) RELAY Board are normal.
the CIS (B) RELAY Board are normal.
→ CN3006-34
th
, 35
th
pins: 5 MHz
: Only for KV-S3065CW Series
→ CN3007-28
th
, 29
th
pins: 5 MHz
: Only for KV-S3065CL Series
3.
Check the soldering condition of the
IC1012, IC1013, IC1024, and their
surrounding circuit on the CONTROL
Board.
IC1012, IC1013, IC1024, and their
surrounding circuit on the CONTROL
Board.
4.
Check the soldering condition of the
IC1008, IC1009, and their surrounding
circuit on the CONTROL Board.
IC1008, IC1009, and their surrounding
circuit on the CONTROL Board.
5.
Check the soldering condition of the
IC2046 and its surrounding circuit on the
INTERFACE Board.
IC2046 and its surrounding circuit on the
INTERFACE Board.
6.
Replace faulty parts or boards.
125
KV-S3065CLSERIES / KV-S3065CWSERIES
Error Code
Possible Cause
Check Point
Remarks
Classified Code
ST1
ST2
ST3
ST4
F63
(Back side black
level error)
(Back side black
level error)
53
00
00
00
Pixel data from CIS (B) or image
processing circuit have some
problems.
processing circuit have some
problems.
1.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
CIS (B) to CN3006 (CIS (B) RELAY
Board): Only for KV-S3065CW
Series
Board): Only for KV-S3065CW
Series
b.
CIS (B) to CN3007 (CIS (B) RELAY
Board): Only for KV-S3065CL Series
Board): Only for KV-S3065CL Series
c.
CN3004 (CIS (B) RELAY Board) to
CN1004 (CONTROL Board)
CN1004 (CONTROL Board)
d.
CN3005 (CIS (B) RELAY Board) to
CN1005 (CONTROL Board)
CN1005 (CONTROL Board)
e.
CN1000 (CONTROL Board) to
CN2000 (INTERFACE Board)
CN2000 (INTERFACE Board)
2.
Check the following CIS timing signals on
the CIS (B) RELAY Board are normal.
the CIS (B) RELAY Board are normal.
→ CN3006-34
th
, 35
th
pins: 5 MHz
: Only for KV-S3065CW Series
→ CN3007-28
th
, 29
th
pins: 5 MHz
: Only for KV-S3065CL Series
3.
Check the soldering condition of the
IC1012, IC1013, IC1024, and their
surrounding circuit on the CONTROL
Board.
IC1012, IC1013, IC1024, and their
surrounding circuit on the CONTROL
Board.
4.
Check the soldering condition of the
IC1008, IC1009, and their surrounding
circuit on the CONTROL Board.
IC1008, IC1009, and their surrounding
circuit on the CONTROL Board.
5.
Check the soldering condition of the
IC2046 and its surrounding circuit on the
INTERFACE Board.
IC2046 and its surrounding circuit on the
INTERFACE Board.
6.
Replace faulty parts or boards.
126
KV-S3065CLSERIES / KV-S3065CWSERIES
Error Code
Possible Cause
Check Point
Remarks
Classified Code
ST1
ST2
ST3
ST4
F80
(Double Feed
Detector
adjustment error)
(Double Feed
Detector
adjustment error)
60
00
00
00
1. Double Feed Detector (G) does
not work, properly.
not work, properly.
1.
Execute Double Feed test in Sec.9.3.6 to
check the detector condition.
check the detector condition.
2.
Check whether the Double Feed Detector
(G) is aligned properly.
(G) is aligned properly.
3.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
Double Feed Detector (G) to CN5031
(RELAY (UPPER) Board)
(RELAY (UPPER) Board)
b.
CN5022 (RELAY (UPPER) Board) to
CN1014 (CONTROL Board)
CN1014 (CONTROL Board)
4.
Check the following parts’ soldering
condition to repair it.
condition to repair it.
a.
CONTROL Board
IC1024 (43, 44, 45
th
pins), IC1018
b.
RELAY (UPPER) Board
IC5013, Q5018, Q5020, Q5021,
Q5022, Q5024, Q5025, Q5027,
Q5028, Q5029, and the surround
circuit
Q5022, Q5024, Q5025, Q5027,
Q5028, Q5029, and the surround
circuit
5.
Check the following signals.
a.
DC 24V signal (CN5022-9
th
pin)
b.
JS_CLK (CN5022-11
th
pin)
→ 200 kHz
c.
USOUND (CN5031-1
st
pin)
→ 200 kHz
6.
Replace faulty parts or boards.
2. Double Feed Detector (R) does
not work, properly.
not work, properly.
1.
Execute Double Feed test in Sec.9.3.6 to
check the detector condition.
check the detector condition.
2.
Check whether the Double Feed Detector
(R) is aligned properly.
(R) is aligned properly.
3.
Check the following connection and
soldering condition on each connector.
soldering condition on each connector.
a.
Double Feed Detector (R) to CN5011
(RELAY (LOWER) Board)
(RELAY (LOWER) Board)
b.
CN5007 (RELAY (LOWER) Board) to
CN1013 (CONTROL Board)
CN1013 (CONTROL Board)
4.
Check the following parts’ soldering
condition to repair it.
condition to repair it.
a.
CONTROL Board
IC1024 (117
th
pin)
b.
RELAY (LOWER) Board
IC5000, IC5001, Q5005, Q5006, and
the surround circuit
the surround circuit
5.
Check the following signals on the RELAY
(LOWER) Board.
(LOWER) Board.
a.
IC5001-7
th
pin: DC 12 V
b.
IC5000-7
th
pin: See Fig.10.2.5.
6.
Replace faulty parts or boards.
127
KV-S3065CLSERIES / KV-S3065CWSERIES
Fig.10.2.1
Fig.10.2.2
Fig.10.2.3
128
KV-S3065CLSERIES / KV-S3065CWSERIES
