Panasonic KV-S1025CSERIES / KV-S1020CSERIES (serv.man2) Service Manual ▷ View online
49
8.3.4.
Lamp Drive Board (F)
(1) Remove the Rear Cover. (See 8.2.5.)
(2) Remove the CONTROL Board. (See 8.4.4.)
(3) Release the connector cables from the clamps inside and
outside of the Base Plate.
(4) Remove the 5 screws and the screw with the FG cable.
outside of the Base Plate.
(4) Remove the 5 screws and the screw with the FG cable.
(5) Remove the Base Plate, paying attention to the contact
between the cables and the plate edge.
between the cables and the plate edge.
(6) Remove the Ground (Earth) Plate 2.
(7) Remove the 2 screws, and disconnect the 2 connectors.
50
8.3.5.
Optical Unit (F)
(1) Remove the Rear Cover. (See 8.2.5.)
(2) Remove the CONTROL Board. (See 8.4.4.)
(3) Release the connector cables from the clamps inside and
outside of the Base Plate.
(4) Remove the 5 screws and the screw with the FG cable.
outside of the Base Plate.
(4) Remove the 5 screws and the screw with the FG cable.
(5) Remove the Base Plate, paying attention to the contact
between the cables and the plate edge.
between the cables and the plate edge.
(6) Remove the Ground (Earth) Plate 2.
(7) Release the cable from the clamp, and disconnect the CCD
Board (F) connector.
Board (F) connector.
(8) Remove the 2 screws.
51
8.3.6.
Lamp (F)
(1) Remove the Optical Unit (F). (See 8.3.5.)
(2) Disconnect the connector from the Lamp Drive Board (F).
(3) Remove the 2 screws.
(3) Remove the 2 screws.
(4) Pull out the Cable 1 in the direction of the arrow (1),
and then pull out the Cable 2 in the direction of the
arrow (2), so that the Lamp Holder (F) can be held
upwards easily.
(5) Slide Lamp Holder (F) slightly in the direction of the
arrow (3), and lift the holder.
and then pull out the Cable 2 in the direction of the
arrow (2), so that the Lamp Holder (F) can be held
upwards easily.
(5) Slide Lamp Holder (F) slightly in the direction of the
arrow (3), and lift the holder.
(6) Unhook the wires, and remove the Lamp (F).
Reassembling Note:
Reassembling Note:
When attaching the Lamp Holder (F) to the scanner,
insert the hooks of the holder to the holes and slide
them in the direction of the arrows until they stop.
insert the hooks of the holder to the holes and slide
them in the direction of the arrows until they stop.
52
8.3.7.
Lamp Drive Board (B): Available only for KV-S1025C Series
8.3.8.
Optical Unit (B): Available only for KV-S1025C Series
(1) Remove the Top Cover. (See 8.2.6.)
(2) Remove the screw.
(3) Disconnect the 2 connectors.
(4) Remove the Lamp Drive Board (B), paying attention to the
2 Claws supporting the board.
2 Claws supporting the board.
(1) Remove the Top Cover. (See 8.2.6.)
(2) Release 2 clamps securing the wires.
(3) Disconnect the connector to the CCD Board (B).
(4) Remove the 2 screws.
(5) While leaning the unit forward in the direction of the
arrow (1), pull out the Optical Unit (B) backward in the
direction of the arrow (2).
arrow (1), pull out the Optical Unit (B) backward in the
direction of the arrow (2).
Click on the first or last page to see other KV-S1025CSERIES / KV-S1020CSERIES (serv.man2) service manuals if exist.