DOWNLOAD Panasonic SDR-S100PP / SDR-S100E / SDR-S100EB / SDR-S100EG / SDR-S100GC / SDR-S100GK Service Manual ↓ Size: 3.73 MB | Pages: 75 in PDF or view online for FREE

9

This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
Also, the contents which is not covered in this issue of Service Manual may be available in Volume-1 Service Manual. (Order No.:
VM0509041CE)

PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB.

• Pb free solder has a higher melting point than standard solder, Typically the melting point is 50-70

°F (30-40°C) higher.

Please use a high temperature soldering iron. In case of soldering iron with temperature control, please set it to 700±20

°F

(370±10

°C).

• Pb free solder will tend to splash when heated too high (about 1100

°F/600°C).

When soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure to heat the sol-
dering points with the Pb free solder until it melts enough.

10

There are five kinds of SDR-S100, regardless of the colours.

• a) SDR-S100S
• b) SDR-S100PP
• c) SDR-S100E/EB/EG
• d) SDR-S100GC
• e) SDR-S100GK

(SDR-S100S is exclusively Japan domestic model.)
What is the difference is that the “INITIAL SETTING” data which is stored in Flash ROM mounted on Main PCB (R).

To define the model suffix to be serviced, refer to the rating label which is putted on the bottom side of the Unit.

After replacing the MAIN PCB (L), (R), be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site
in “TSN system”, together with Maintenance software.

11

12

After replacing the MAIN PCB (L), (R), be sure to achieve adjustment.
The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-PAVC” web-site in
“TSN system”, together with Maintenance software.

This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.

Table S1 Extension Cable List

1

VFK1440

FP6101 (MAIN R) - FP4801 (MIC)

10PIN 0.5 FFC

2

VFK1286

FP6104 (MAIN R) - REAR CASE UNIT

16PIN 0.5 FFC

3

VFK1491

FP6102 (MAIN R) - FP4001 (FRONT)

27PIN 0.3 FFC

4

VFK1978

FP6103 (MAIN R) - FP901 (MONITOR)

31-27PIN 0.3 FFC

5

VFK1582BF010

PP6101 (MAIN R) - PS6001 (MAIN L)

150PIN B to B

6

VFK1443

FP6105 (MAIN R) - BUS FPC

18PIN 0.5 FFC

8

VFK1575C3320

FP6002 (MAIN L) - LENS UNIT

33PIN 0.3 FFC

9

VFK1459

FP6001 (MAIN L) - LENS UNIT

39PIN 0.3 FFC

12

VFK1575C3320

FP7001 (FRONT) - FLASH UNIT

33PIN 0.3 FFC

13

VFK0977

FP902 (MONITOR) - LCD

20PIN 0.5 FFC