Panasonic SDR-H100P / SDR-H100PC / SDR-H100EB / SDR-H100EC / SDR-H100EE / SDR-H100EF / SDR-H100EG / SDR-H100EP / SDR-H100GT / SDR-H101EB / SDR-H101PR / SDR-H101PU / SDR-H101GA / SDR-H101GC / SDR-H101GK / SDR-H101GN Service Manual ▷ View online
41
10 Maintenance
10.1. Cleaning Lens and LCD Panel
Do not touch the surface of the lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
Note:
A lens cleaning paper and lens cleaner are available at local camera shops and market place.
42
11 Factory Setting
Note:
The screens of the factory setting are for SDR-H100P.
For other models, refer to each screen of the factory setting.
For other models, refer to each screen of the factory setting.
11.1. How to turn on the factory setting?
1. Indication method of the service menu
Set the mode switch "
Recording" mode.
2. While keep pressing the "Intelligent auto/Manual" button and "Menu" button, hold left the Zoom Lever towards to "[ W ]" posi-
tion for more than 3 seconds until the top screen of the Service Menu being displayed.
3. Under the condition of the Item No."1" is yellow high lighted, press the "[RIGHT
] of joystick" button.
4. By pressing the "[UP
] of joystick" button, then press the "[center] of joystick" button.
5. After few seconds "END" is displayed on LCD monitor.Cutting of battery connection or AC power supply connection as a com-
pletion of the "FACTORY SETTINGS".
43
11.2. What is the factory settings?
The factory settings clean up and/or refresh the following settings.
1. MENU, MODE, ADJUSTMENT VALUE.
2. SD card format.
3. Reset the folder number and file number of still pictures.
2. SD card format.
3. Reset the folder number and file number of still pictures.
(Setting the folder number is 100, and file number is 0.)
4. Clear the mechanism lock information.
5. Clear the service mode information contents.
6. Clear the date.
7. Initialize the VIERA Link Physical Address.
8. Confirm the data area of HDD is cleared.
5. Clear the service mode information contents.
6. Clear the date.
7. Initialize the VIERA Link Physical Address.
8. Confirm the data area of HDD is cleared.
The setting position of factory settings:
Name
Setting position
Mode switch
Open/close switch
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Rear P.C.B. ........................................................................... S-2
S2.2. Monitor P.C.B. ....................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Rear Schematic Diagram ...................................................... S-5
S4.3. CCD Schematic Diagram ...................................................... S-6
S4.4. EMC Schematic Diagram ...................................................... S-6
S4.5. DC BATT OP FPC Schematic Diagram ................................ S-7
S4.6. HDD FPC Schematic Diagram .............................................. S-8
S4.7. MONI FPC Schematic Diagram ............................................ S-8
S4.8. Monitor Schematic Diagram .................................................. S-9
S4.9. LED Light Schematic Diagram ............................................ S-10
S5. Print Circuit Board .................................................................. S-11
S5.1. Rear P.C.B. ......................................................................... S-11
S5.2. CCD P.C.B. ......................................................................... S-12
S5.3. EMC FPC P.C.B. ................................................................. S-13
S5.4. DC BATT OP FPC P.C.B. .................................................... S-13
S5.5. HDD FPC P.C.B. ................................................................. S-14
S5.6. MONI FPC P.C.B. ................................................................ S-14
S5.7. Monitor P.C.B. ..................................................................... S-18
S5.8. LED Light P.C.B. ................................................................. S-19
S6. Replacement Parts List .......................................................... S-21
S7. Exploded View ....................................................................... S-27
S7.1. Frame and Casing Section.................................................. S-27
S7.2. LCD Section ........................................................................ S-28
S7.3. Lens Section ....................................................................... S-29
S7.4. Packing Parts and Accessories Section .............................. S-30
Table of contents
Service Manual
VM1101003CE
Diagrams and Replacement
Parts List
Vol. 1
(K)........Black Type (except SDR-H101EB)
Colour
(H)........Gray Type (only SDR-H101EB)
(S)........Silver Type (only SDR-H100P/PC/GT, H101PU/GA/GC)
(R)........Red Type (only SDR-H100P/PC/GT, H101PU/GA/GC/GK/GN)
Model No.
SDR-H100P
SDR-H100PC
SDR-H100EB
SDR-H100EC
SDR-H100EE
SDR-H100EF
SDR-H100EG
SDR-H100EP
SDR-H100GT
SDR-H101EB
SDR-H101PR
SDR-H101PU
SDR-H101GA
SDR-H101GC
SDR-H101GK
SDR-H101GN
SD / HDD Video Camera
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
Click on the first or last page to see other SDR-H100P / SDR-H100PC / SDR-H100EB / SDR-H100EC / SDR-H100EE / SDR-H100EF / SDR-H100EG / SDR-H100EP / SDR-H100GT / SDR-H101EB / SDR-H101PR / SDR-H101PU / SDR-H101GA / SDR-H101GC / SDR-H101GK / SDR-H101GN service manuals if exist.