Panasonic NV-GS250E / NV-GS250EG / NV-GS250EB / NV-GS250GC / NV-GS250GN / NV-GS250GCD / NV-GS258GK Service Manual ▷ View online
4 HOW TO REPLACE THE LITHIUM BATTERY
(PROCEDURE)
1. Remove the Side Case (L) C.B.A.. (Refer to Disassembly Procedures.)
2. Unsolder the Lithium Battery “ML-621S/F9D” and then replace the new one. (See Fig. B1.)
3. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Fig. B1
Note:
The lithium battery is a critical component. (Type No.: N9ZZ00000294.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in equipment designed specifically for its use.
Replacement batteries must be of the same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
9
NV-GS250E / NV-GS250EG / NV-GS250EB / NV-GS250GC / NV-GS250GN / NV-GS250GCD / NV-GS258GK
5 ADJUSTMENT PROCEDURES
5.1. DISASSEMBLE FLOW CHART
This flow chart indicates the disassembly steps the cabinet parts, C.B.A. and Mecha. Unit in order to access to be serviced. When
reinstalling, perform the steps in the reverse order.
reinstalling, perform the steps in the reverse order.
Fig. F1
10
NV-GS250E / NV-GS250EG / NV-GS250EB / NV-GS250GC / NV-GS250GN / NV-GS250GCD / NV-GS258GK
5.2. DISASSEMBLY PROCEDURES
Flow-Chart for Disassembly Procedure
No.
Item / Part
Fig.
Removal (Screw,Connector,Flex. &
Other)
1
Front
Case
Unit
Fig. D2
Remove the Grip Belt Piece with the
procedure of arrow 1,2,3.
procedure of arrow 1,2,3.
Fig. D3
2-Screws (A), 2-Screws (B)
Fig. D4
2-Screws (C)
Fig. D5
Open the LCD Unit
1-Screw (D)
1-Screw (D)
Fig. D6
1-Connector FP4801
Front Case Unit
Front Case Unit
2
Side Case (R)
Unit / LCD Unit
Unit / LCD Unit
Fig. D7
3-Screws (E)
Fig. D8
Tilt up the EVF
1-Screw (F), 1-Screw (G)
1-Screw (F), 1-Screw (G)
Fig. D9
2-Connectors FP602, FP6503
2-Tabs
Side Case (R) Unit / LCD Unit
2-Tabs
Side Case (R) Unit / LCD Unit
3
Lens Unit
Fig. D10 1-Screw (H)
2-Connectors FP201, FP701
Lens Unit
Lens Unit
4
EVF Unit
Fig. D11 1-Screw (I), 1-Screw (J)
2-Connectors FP601, FP3402
EVF Unit
EVF Unit
5
Rear
Operation Unit
/ Sub C.B.A.
Operation Unit
/ Sub C.B.A.
Fig. D12 1-Screw (K), 1-Screw (L)
2-Connectors FP1001, FP6502
Rear Operation Unit
1-Connector FP4002
Sub C.B.A.
Rear Operation Unit
1-Connector FP4002
Sub C.B.A.
6
Main C.B.A.
Fig. D13 8-Connectors FP2201, FP2202,
FP2203, FP2204, FP5001, FP6501,
FP6504, FP6505
1-Screw (M)
2-Tabs
Main C.B.A.
FP6504, FP6505
1-Screw (M)
2-Tabs
Main C.B.A.
7
Mecha. Unit
Fig. D14 Open the Cassette Cover
3-Screws (N)
Mecha. Unit
Mecha. Unit
8
Jack C.B.A.
Fig. D15 1-Screw (O), 1-Screw (P), 1-Screw (Q)
Jack C.B.A.
9
Front C.B.A.
Fig. D16 3-Screws (R), 1-Screw (S)
1-Tab
Front C.B.A.
Front C.B.A.
10
Monitor C.B.A. Fig. D17 1-Screw (T), 1-Screw (U), 1-Screw (V),
1-Screw (W)
Hinge Support Plate
Hinge Support Plate
Fig. D18 1-Screw (X)
Fig. D19 1-Tab
Fig. D19 1-Tab
R Cover / LCD Unit
Fig. D20 2-Screws (Y)
6-Tabs
LCD Case (Upper) Unit
LCD Case (Upper) Unit
Fig. D21 1-Connector FP902
LCD Hinge Unit
Fig. D22 1-Connector FP901
2-Tabs
Monitor C.B.A.
Monitor C.B.A.
11
EVF C.B.A.
Fig. D23 2-Screws (Z)
EVF Slide
Fig. D24 1-Tab
View ADJ. Unit
Fig. D25 Remove a,b,c,d department (remove
department previously).
EVF Case (Upper) Unit
Remove e,f department.
EVF Case (Lower) Unit
EVF Case (Upper) Unit
Remove e,f department.
EVF Case (Lower) Unit
Fig. D26 2-Connectors FP801,FP802
2-Tabs
EVF C.B.A.
EVF C.B.A.
Fig. D1
Fig. D2
11
NV-GS250E / NV-GS250EG / NV-GS250EB / NV-GS250GC / NV-GS250GN / NV-GS250GCD / NV-GS258GK
Fig. D3
Fig. D4
Fig. D5
Fig. D6
12
NV-GS250E / NV-GS250EG / NV-GS250EB / NV-GS250GC / NV-GS250GN / NV-GS250GCD / NV-GS258GK
Click on the first or last page to see other NV-GS250E / NV-GS250EG / NV-GS250EB / NV-GS250GC / NV-GS250GN / NV-GS250GCD / NV-GS258GK service manuals if exist.