Panasonic HDC-HS80P / HDC-HS80PC / HDC-HS80PU / HDC-HS80EB / HDC-HS80EC / HDC-HS80EE / HDC-HS80EG / HDC-HS80EP / HDC-HS80GA / HDC-HS80GC / HDC-HS80GN / HDC-HS80GT / HDC-HS80GK / HDC-HS80EE9K Service Manual ▷ View online
37
10 Factory Setting
10.1. How To Turn On The Factory Settings?
1. Set the mode switch “Motion Picture Recording” mode.
2. While the power is turned OFF, keep pressing the “Power” button, “Zoom lever” to W side and “intelligent auto/Manual” button
2. While the power is turned OFF, keep pressing the “Power” button, “Zoom lever” to W side and “intelligent auto/Manual” button
for more than 3 seconds until the top screen of the Service Mode Menu being displayed.
3. Touch the [ 1 ] of LCD.
4. Touch the [ YES ] of LCD.
5. After few seconds “END” is displayed or “HDD NODATA” as “NG” is displayed on LCD monitor. Cutting of battery connection
4. Touch the [ YES ] of LCD.
5. After few seconds “END” is displayed or “HDD NODATA” as “NG” is displayed on LCD monitor. Cutting of battery connection
or AC power supply connection as a completion of the “FACTORY SETTINGS”.
(After use at least once, even if the physical format of the HDD unit will be performed, “HDD NODATA” as “NG” is indicated,
but “FACTORY SETTINGS” is completed.)
(After use at least once, even if the physical format of the HDD unit will be performed, “HDD NODATA” as “NG” is indicated,
but “FACTORY SETTINGS” is completed.)
38
10.2. What Is The Factory Settings?
The factory settings clean up and/or refresh the following settings.
1. MENU, MODE, ADJUSTMENT VALUE.
2. SD card format.
3. Reset the folder number and file number of still pictures.
2. SD card format.
3. Reset the folder number and file number of still pictures.
(Setting the folder number is 100, and file number is 0.)
4. Clear the mechanism lock information.
5. Clear the service mode information contents.
6. Close the lens cover
7. Initialize the VIERA Link Physical Address.
5. Clear the service mode information contents.
6. Close the lens cover
7. Initialize the VIERA Link Physical Address.
If the "Factory Settings" is completed, physical format of the HDD unit is not performed, execute physical format according to the
following procedure.
following procedure.
The setting position of factory settings:
Name
Setting position
Mode switch
Motion picture recording mode
S-1
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. SD P.C.B. .............................................................................. S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. SD Schematic Diagram ......................................................... S-5
S5. Print Circuit Board .................................................................... S-6
S5.1. SD P.C.B. .............................................................................. S-6
S6. Replacement Parts List ............................................................ S-7
S7. Exploded View ....................................................................... S-11
S7.1. Frame and Casing Section.................................................. S-11
S7.2. Packing Parts and Accessories Section .............................. S-12
Table of contents
Service Manual
VM1102015CE
Diagrams and Replacement
Parts List
Vol. 1
Colour
Model No.
HDC-HS80P
HDC-HS80PC
HDC-HS80PU
HDC-HS80EB
HDC-HS80EC
HDC-HS80EE
HDC-HS80EG
HDC-HS80EP
High Definition Video Camera
(K)...........Black Type
HDC-HS80GA
HDC-HS80GC
HDC-HS80GN
HDC-HS80GT
HDC-HS80GK
Name of Signal
OFTR
FEP
This signal is connected
to the FEP schematic diagram.
Circuit name being connected.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
7.Indication on Schematic diagrams:
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
COMPONENTS IDENTIFIED WITH THE MARK
HAVE THE SPECIAL CHARACTERISTICS
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
S-2
S2. Voltage Chart
S2.1. SD P.C.B.
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard.
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
REF No.
PIN No. POWER ON
Q3901
E
3.3
Q3901
C
0
Q3901
B
3.3
QR6401
E
2.9
QR6401
C
-0.4
QR6401
B
2.9
QR6402
E
2.9
QR6402
C
-0.4
QR6402
B
2.9
Click on the first or last page to see other HDC-HS80P / HDC-HS80PC / HDC-HS80PU / HDC-HS80EB / HDC-HS80EC / HDC-HS80EE / HDC-HS80EG / HDC-HS80EP / HDC-HS80GA / HDC-HS80GC / HDC-HS80GN / HDC-HS80GT / HDC-HS80GK / HDC-HS80EE9K service manuals if exist.