Panasonic SR-DF101WTQ / SR-DF181 Service Manual ▷ View online
22
4
Remove the body
•
Lay the cooker for service on a rubber sheet or similar so
as not to damage the unit. Insert the slotted screwdriver
30-40mm upwards as the fi gure shown.
as not to damage the unit. Insert the slotted screwdriver
30-40mm upwards as the fi gure shown.
• Remove the body by applying force on the slotted
screwdriver in the direction indicated by the arrow on the
right fi gure.
right fi gure.
NOTES:
NOTES:
•
Don’t tap the slotted screwdriver to remove the body
which may cause damage to contact part of screwdriver.
The above procedures must be followed.
which may cause damage to contact part of screwdriver.
The above procedures must be followed.
5
Disconnect the wirings on the control board
•
Please use needle nose pliers to pull out each connector.
•
Use needle nose pliers to pull out fasten terminal
(2 places)
(2 places)
NOTES:
NOTES:
•
When pulling out the plug or similar, pull directly in the
outward direction. If pulling in different directions, it may
place pressure on the control board and cause damage to
the coil and breakdown of PCB.
outward direction. If pulling in different directions, it may
place pressure on the control board and cause damage to
the coil and breakdown of PCB.
• To pull out the fasten terminal, please press down the
stopper in the direction of the arrow shown in the fi gure,
and pull outwards at the same time. Otherwise, the fasten
terminal couldn’t be pulled out.
and pull outwards at the same time. Otherwise, the fasten
terminal couldn’t be pulled out.
IP3830_SR-DF101_Eng_19_121224.in章节1:22 章节1:22
2012-12-24 17:19:45
23
6
Remove the base for control PCB
•
Unplug the wiring which connects with the control PCB
• Remove
fi xing screw (×1).
• Hold the base for PCB and take it out directly.
* For the sake of safety, make sure you wear an ESD-
protective wrist strap or take preventive measures.
7
Take out the components of control PCB
•
Break off the stationary claws slightly, lift up the control PCB (operation parts) and take them out.
• Use the same method to remove control PCB (power parts) and take it out.
व⟾
व⟾
8
Assembly of base for control PCB
• Reassemble the base of PCB for complete power in reverse order for disassembly.
NOTES:
NOTES:
• Refer to P5 for wiring connection.
• When assembling, make sure to paste the fl ame retardant tape on the initial position as before.
claw
claw
IP3830_SR-DF101_Eng_19_121224.in章节1:23 章节1:23
2012-12-24 17:19:45
24
11 The exchange method of cast heater
1
Remove terminal for complete power and body
•
Refer to the exchange method of base for control PCB (See item 1 to 4, P13), remove the terminal and body.
2
Remove the cast heater
•
Remove the fi xing screws (×2) of cast heater.
• Take out the cast heater from inner enclosure.
2
Reassembly
•
Reassemble the new cast heater in reverse order for disassembly.
NOTES:
NOTES:
•
Refer to P5 for wiring connection.
• When assembling, make sure to paste the fl ame retardant tape on the initial position as before.
IP3830_SR-DF101_Eng_19_121224.in章节1:24 章节1:24
2012-12-24 17:19:45
25
12 The exchange method of pan sensor and thermal fuse
1
Remove the cast heater
• To remove the cast heater, please refer to “The exchange method of cast heater” (Item 1 to 3, P16).
2
Remove pan sensor
• Loosen and stretch out the claws (3 places) and take out
the pan sensor.
NOTES:
NOTES:
• Care must be taken to avoid the spring for sensor from
deformation when removing.
3
Exchange thermal fuse
• The replacement of pan sensor is the exchange of thermal fuse A/B.
This is because the thermal fuse A/B are both fi xed within the pan sensor.
This is because the thermal fuse A/B are both fi xed within the pan sensor.
4
Reassembly
• Reassemble the new pan sensor in reverse order for disassembly.
NOTES:
NOTES:
• Care must be taken to avoid the spring for sensor from deformation when reassembling.
• Care must be taken to avoid the spring for sensor from tilting when reassembling.
• Refer to P5 for wiring connection.
• Please note the direction of pan sensor.
• Care must be taken to avoid the spring for sensor from tilting when reassembling.
• Refer to P5 for wiring connection.
• Please note the direction of pan sensor.
claws (3 places)
Thermal Fuse B
Thermal Fuse A
Thermistor
IP3830_SR-DF101_Eng_19_121224.in章节1:25 章节1:25
2012-12-24 17:19:46
Click on the first or last page to see other SR-DF101WTQ / SR-DF181 service manuals if exist.